Tender For Repairs And Renovation Of Vac Building , Residental Quarter At Rajgad Tq Mul Ts No --------------------------------------------Rs 2057000/- Part A
Tender Value
20.57 Lakhs
Estimated cost
Bid Submission
09 Nov 2026
9 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandrapur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs And Renovation Of Vac Building , Residental Quarter At Rajgad Tq Mul Ts No --------------------------------------------Rs 2057000/- Part A
BOQ
| Sl. No. | Item Description |
| 1 | Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.Spec.No.: As directed by Engineer in charge. |
| 2 | Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete.Spec.No.: As directed by Engineer- in-charge. |
| 3 | Removing cement tiles or marble or polished shahabadfloorordadowithoutbedconcreteincludingstackingthematerialsasdirectedwithall leads, lifts etc. complete |
| 4 | Removing limeor lean cement concrete including stacking thespoilsas directed with all leads, lifts etc, complete.Spec.No.: As directed by Engineer- in-charge. |
| 5 | Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means |
| 6 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete. |
| 7 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) |
| 8 | Providing internal cement plaster 12 mm thick in a single coat in cement mortar 1:4 to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B.Masonry and concrete members complete. [2/BDL/2B,P NO-36] Spec.No.: Bd. L.2 Page Number 368 |
| 9 | Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. a) Flooring |
| 10 | Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete. b) Skirting |
| 11 | Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. |
| 12 | Providing and laying Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.Bd. M-12 page One Number 385 |
| 13 | Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. |
| 14 | Providing and laying telephone black / AmbaWhite / Cadburybrown / Ruby red /OceanBrowngranitestoneof18to20mmthickfordoorframe/dado/windowboxingetc.OnC.M. 1:6 includingfilling jointswithpolymerbase fillernosing/moulding thesharp edges wherever necessary, curing, etc. complete |
| 15 | Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item No. 15 to 18 prior approval of Superintending Engineer will be necessary Spec. No. : As directed by Engineer in charge. |
| 16 | Providing and applying plastic emulsion paint of approved quality ,colour and shade to old and new surfaces in two coat sincluding scaffolding,preparingthesurface.(excludingtheprimercoat)etc.complete.Spec. No. Bd.P.5 Page No. 413 |
| 17 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete |
| 18 | Providing and fixing Country cut teak wood single leaf panelled door shutters 35 mm thick style and rail and 19 mm thick T.W. panels as per detailed drawing including wrought iron hold fast stainless steel fixtures and fastening and three coats of oil painting etc. complete. |
| 19 | Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.Bd.O.5 Page No. 405 |
| 20 | Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box. |
| 21 | Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sqm /kg with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.Spec.No.: As directed by Engineer in charge |
| 22 | Providing and laying damp proof course 50 mm thick in M20 cement concrete layer and bitumen / using cement with waterproofing compound curing, formwork etc. complete. Spec.No.: Bd.J.2 Page No. 355 |
| 23 | Clean the surface to removedirt, looseparticles.Examine the surfacecloselyfor anycracks.Cleanthecracks.Provideandfillapureacrylic,polymermodifiedreadytousepastePolyfillAR ofapprovedmake&approvedbyEngineer inchargehavingacreamcolouredviscousemulsionreadytouseacrylicpolymericnon-shrinkcrackfillerputtywithautosuctionpropertiesandrequiringnobondingagent,nocuringandnorequirementforopening theexistingcracks finishingwithsubsequent fillingas required. Provideandapply three coats of 100%acrylicwaterproof heat insulating breathable decorativeexternalcoatingSunext8 ofapprovedmake&approvedbyEngineer incharge, inthedesiredshade.Stirwell andapplybybrushfor threecoats.Applyingthreecoatsat aninterval of 4-6 hours between each coat.High Performance 100%Acrylic, Waterproof, Anti-fungal, Anti-carbonation, HeatInsulating External Paint should have following minimum properties:1. Specific Gravity: 1.3 ± 0.1 at 25°C2. pH: 7.0 to 10.003.Viscosity: 18 to30sec. at 25°CbyFordCupOneNumberB-4(Dilute2partsofproduct with 1 part of water)4. CO2 diffusion resistance co- efficient (DIN EN 1062-6 (2002-10): 7.59 x1055.CO2diffusionequivalentairlayerthickness(DINEN1062-6(2002-10):127m@190microns DFT6. Adhesion (ASTM D 4541): 2.3 N/mm2 (Concrete / Substrate Failure)7. Solar Reflectance Index (ASTM E 1980 11,EN 673:2011, EN 410:2011): 107 It shall be applied as per manufacturers specification. |
| 24 | Providing and fixing fiber glass reinforce dpolyster door shutter 30mm thick as per IS14856(2000) (Reaffirmed2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete Spec. No. : As directed by Engineer incharge. |
| 25 | Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. |
| 26 | Providing and fixing Orissa type white glazed earthenware 575 mm water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. |
| 27 | Providing and fixing 8 cm rigid PVC Nahani trap including PVC grating ,bend, connecting piece of UPVC pipe up to the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necessary before use) Spec.No.: Specfications |
| 28 | Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 29 | Providing soak pit of size 120cm x 120cm x 120cm including excavating and filling with brick-bats. |
| 30 | Providing, laying and fixing P.V.C. pipe of 15 mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 31 | Providing, laying and fixing P.V.C. pipe of 25mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. |
| 32 | Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete. Spec.No.: Bd.V.8/Page No.554 |
| 33 | Providing and fixing screw down 15 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete Spec.No.: Bd.V.9/Page No.555 |
| 34 | Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. Complete Spec.No.: spacifications |
| 35 | Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters |
| 36 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.8 Page No. 302 and B.7, Page No.38 |
| 37 | Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hookingthe bars, binding with wires or tack welding and supporting as required complete. Bd.F.17, Page No. 306 |
| 38 | Providing and laying in situ / ready mix controlled grade of M15 of trap /granite /quartzite /gneiss metal for RCC works in cut off walls / curtain walls including necessary scaffolding, centering, compacting by vibrator, finishing and curing etc. complete. (withOUT fully automatic micro processor based PLC withOUT SCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with natural /artifical sand, excluding reinforcement) SPEC NO- BE59 a As directed by Engineer in charge. |
| 39 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.6 Page No. 300 and B.7, Page No.38 |
| 40 | Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand Bd.F.5 Page No. 300 and B.7, Page.No. 38 |
| 41 | Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. CompleteAs director by engineer incharge and BDG- 2 and 5 |
| 42 | Construction of granular sub-base by providing close grade dmaterial, spreading in uniform layers with motor grader/Paver on prepare d surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desire ddensity,complete as per clause 401 -- By Mix in Place Method and Grading - III Material spec no-MORTH 401 |
| 43 | Providing and fixing heavy duty interlocking concrete RUBBER MOULD GLOSSY PAVING BLOCKS of 60millimeter thickness of having a strength of 400Kg/sq.m of approved quality and shape on abed of crushed sand of 25 to 30 millimeter thick including striking joint sand cleaning etc. complete. (using 100% crushed sand) spec no-Bd. M-12 page Number 385 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender