Tender For Special Repair To Refueler Bay Of Refueler Section Alongwith Construction Of Wash Room At Bldg No P-13 And Provn Of Shed With Plinth And Walls For Isolation Transformer, Voltage Stabilizer And Distribution Panel At Af Stn Bhuj
Tender Value
38.54 Lakhs
Estimated cost
Bid Submission
18 Nov 2026
17 days left
EMD
77080
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kachchh → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Refueler Bay Of Refueler Section Alongwith Construction Of Wash Room At Bldg No P-13 And Provn Of Shed With Plinth And Walls For Isolation Transformer, Voltage Stabilizer And Distribution Panel At Af Stn Bhuj
BOQ
| Sl. No. | Item Description |
| 1 | Demolition unreinforced Cement Concrete of any description and in any position not otherwise specifically provided for, complete all as specified and as directed. |
| 2 | M&L Cement Concrete C2 1:3:6 (40mm graded stone aggregate), 75mm thick as in Plinth Protection, etc., laid in alternate bays, finishing Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed. |
| 3 | M&L for Forming Construction joint 30mm deep x 10mm wide filled with sealing compound grade 'B' complete all as specified and as dircted |
| 4 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed |
| 5 | M&L For Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately |
| 6 | M&L for removing building materials etc.from MD Land, beyond the lead included in the rates, including loading, unloading and stacking at the destination |
| 7 | M&L for form work to side and soffits of floor or roof beams, lintels, cantilever, shelves including supports etc for rough finished surface of conc all as specified. |
| 8 | M&L RCC M-25 design mix by using 20 mm graded crushed stone aggregate as in beams supported on walls complete. |
| 9 | M&L for form work to soffits of suspended slabs, such as roof slabs floor slabs and similar work not exc 200 mm thick for rough finished surfaces of concrete all as specified. |
| 10 | M&L for Formwork for Rough finished surfaces of concrete to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide. |
| 11 | M&L for reinforced cement concrete M-25 design mix in slab supported on walls, beams and column in floor roof and landing all as specified. |
| 12 | S&F MS TMT bars 10 mm dia and over cut to length bent to shape required incl, cranking bending spirally for hooping for column hooking ends binding with and incl MS wire (annealed) not less than 0.9 mm dia |
| 13 | All as per item No 12 abvoe , but 5 MM dia and over upto and including 10MM dia in stirrups spacers and binders. |
| 14 | Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including disposal of rubbish to the dumping ground with in 50mtr lead complete all as specified and as directed by the Engr-in-Charge. |
| 15 | Supply & fix GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete all as specified and as directed by the Engr-in-Charge |
| 16 | Material & labour for rendering 15mm thick in cement sand mortar 1:4 on fair faces of brick work, PCC block masonry or concrete surfaces, mixed with water proofing compound and finished even and smooth without using extra cement as per manufacturer's instructions complete all as specified and as directed by the Engr-in-Charge. Note:- (a) Supply only Integral water proofing compound will be measured and paid seperately (b) Height of building may vary from 3 m to 6 m. |
| 17 | Supply only integral water proofing compound complete all as specified and as directed by the Engr-in-Charge |
| 18 | Material & labour for 15mm thick cement plastering in cement mortar 1:6 on fair faces of stone work or concrete surfaces finished even & smooth without using extra cement complete all as specified and as directed by the Engr-in-ChargeNOTE: Height of building may vary from 3 m to 6 m. |
| 19 | Material & labour for 5 mm thick cement plastering in cement mortar 1:3 on fair faces of ceiling surfaces finished even & smooth without using extra cement complete all as specified and as directed by the Engr-in-ChargeNOTE: Height of building may vary from 3 m to 6 m. |
| 20 | Material & labour for preparation of new or previously untreated concrete/plaster surfaces and applying two coats of exterior emulsion paint (in camouflage pattern) as approved by the GE over a coat of primer complete all as specified and as directed by the Engr-in-Charge |
| 21 | M&L for complete removal of existing treatment & preparation of plastered or unplastered old decorated external surfaces of walls by Vaccum Based sanding machine and applying two coats of exterior emulsion paint over coat of primer in camouflage pattern as approved by the GE, all as specified and directed. |
| 22 | M&L preparing new surfaces of walls and applying 3mm thick wall care putty and two coat of distemper oil emulsion over a coat of primer complete all as specified and directed. |
| 23 | Material & labour for preparation of new untreated surfaces of ceiling and appying three coats of white wash complete all as specified and as directed by the Engr-in-Charge |
| 24 | M&L for 25 mm PCC 1:2:4 type C-0 (using 12.5 mm graded stone aggregate) as in roof padding as directed by Engr-in-Charge. |
| 25 | Material & labour for Screed bed 15mm thick in CM 1:3 over RCC roof mixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 26 | Material & labour for Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the samemembrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm.complete all as specified and directed by Engineer-in-Charge. |
| 27 | M&L50 mm thick for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in path/ hard standing finishing smooth without using extra cement complete all as specified. |
| 28 | Demolition of stone masonry built in cement mortar including all quoins arches pillars etc but excluding ashlar facing works , dressed stone and precast concrete article. |
| 29 | M&L for block masonry with precast cement concrete type 1:3:6 (20mm graded stone aggregate) solid blocks exc 10cm in width and setting in cement mortar 1:6. |
| 30 | Taking down Old U/S point wiring and accessories complete. |
| 31 | Taking down Old U/S submain wiring and accessories complete. |
| 32 | Taking down Old U/S DBs and accessories complete. |
| 33 | M & L for one light point/ fan point controlled by one, one way flame proof switch surface type wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade drawn through ERW steel conduit heavy duty ISI mark of size 20mm external dia with all accessories like tees, bends elbows, reducers bell mouth tube ends and fixing accessories such as couplers, lock nuts saddles, pipe hooks etc as specified |
| 34 | All as per item No 33 but with 2.5 Sqmm all as specified and directed by Engr-in- Charge |
| 35 | Supply and fixing flame proof/weather proof 4 feet LED light fitting 2x20 Watt (product cat No)SSPL/FF/1271, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size |
| 36 | Supply and fix Switch flame proof rotary type with termination box inLM6, 16A, single pole 250VAC single pole 9LM-6) alluminium along with flame proof cable glands CMRS certified ISI marked complite all as specified and dirrected by Engr In charge |
| 37 | M&L for sub main wiring with two runs of PVC insulated and unsheathed FRLSH cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 2.5 Sqmm single core, copper conductor drawn through ERW steel conduit heavy duty ISI mark of size 20mm external dia and 2.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire complete all as specified and directed(Note: Two runs of conductor with one run of earth wire will be measured & paid as one unit) |
| 38 | M&L for Flame proof/Weather proof switch socket & plug combined in LM6 cable termination box in LM6, 16A, 250V, 2P+earth., |
| 39 | Supply and Fix FLP-WP 4 Way SPN Distribution Board consisting of : Incoming: 1 No. 32 Amp. DB MCB . Outgoing :1 nos. 32A DP MCB, Outgoing : 2 nos. 10 A DB MCB InLM6 construction with 1 no 11/2\\" ET, 1 nos .3/4\\"ET and 2 nos 1\\"ET cable entries from bottom bu twith out cable glands ,light greye poxy powder coated ,SS hardware Certified by CIMFR, Dhanbad for Gas Gr.II A& II B as per IS/IEC-60079 as per directed by engineer in charge. |
| 40 | M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to depth not less than 2.25 mtr below ground level with top edge of earth plate at a depth not less than 1.5 mtr below normal ground level connected to and including GI strip of 25 x 4 mm as earth lead up to 7.5 mtr long fixed by means of bolts, nuts, check nuts and washers etc. of galvanised iron or steel including provn of uPVC pipe of 40mm bore and connected to earth strip earthing test point all as shown in electrical plate No.5 of SSR Part-I 2009 and as specified or indicated and testing on completion including necessary excavation & earthwork in any type of soil, PCC (1:3:6) type C1 chamber, precast slab 50mm thick in cement concrete (1:2:4)type B1 (reinforced with welded steel wire fabric (XPM) of weight not less than 4kg/sqm) with frame, funnel with watering pipe of 15mm bore , wire mesh and lugs, test point etc. complete. Note: G I strip exceeding 7.5m long shall be measured & paid separately. |
| 41 | Supply and fixing single pointed air termination aluminium rod, 12 mm dia, 300 mm long. |
| 42 | Aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground |
| 43 | S&F Test Point terminal box made out of Gun Metal or Phosporous Bronze / copper of size 75x75x25mm drilled and screwed including 3 Nos 8mm dia 25mm long hexagonal head copper screws, etc complete all as specified and as directed by Enginner-in- charge. |
| 44 | PCC 1:2:4 type B-1, using 20mm graded crushed stone aggregate as in coping of poles and like incl watering,slightly rounded of chamfered angles and throating incl. necessary form work,complete all as specified. |
| 45 | S&F High density polyethylene (HDPE) pipes of pressure rating 6 kgf/sq. cm of 40mm bore complete with elbows, couplers etc and with MS Clamps, nuts, bolts, washers etc for fixing of pipe to wall/floor and laying in trenches for protection complete all as specified and as directed |
| 46 | M & L for GI strip along with flexible conduit of size 25x4 alongwith insulator complete all as specified as directed. |
| 47 | Excavating in post holes (or similar holes) in hard and dense soil , each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M deep and getting out in any type of soil. |
| 49 | Returning,Filling,including spreading ,levelling,watering and well ramming in layers not exe.25 cm in any type of soil |
| 50 | Removing surplus soil to a distance exceeding 250 Mtr and not exceeding 500 Mtr and deposited where directed. |
| 51 | Material and labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations and mass concrete complete. |
| 52 | M&L for Hard core of gauge n.exc.63 mm, broken stone & boulders deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface. |
| 53 | M/L for rendering 10mm thick on CM (1:3) on concrete roof top and chajjas surface finished even and smooth to get uniform level surface for laying of membrane treatement,with using water proofing compound. |
| 54 | M&L for Powder coated aluminium window/ventilators with double side hung shutter for glazing and gauging and frame with one or more rebates made out anodised aluminium section including section for fixing of aluminium grills with suitable fixtures, jointing cleats for fixing clips, rubber packing, anodised aluminium snap beading screws, anodised aluminium beading screws, type B20 100mm long suitable handle and anodised alumium fittings such as stay, hinges glazing with 5.0 mm thick tinted sheet glass and gauging with aluminium wire cloth of size 0.45mm dia of wire and 1.40mm apperture except fixed glazinng (FG) all as specified and directed. (Tint of glass shall be approved by GE ,5mm thick glass sheet glass or tinted glass appx 0.70 Sqm And wiremesh appx 0.70 Sqm included in this item). |
| 55 | M&L 15mm thick rendering in cement mortar 1:4 to stone masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even for fixing tiles etc complete all as specified and directed by Engineer - in - Charge. |
| 56 | M&L for 450x300 x 7mm thick glazed coloured ceramic wall tiles/ digital tiles as in vertical surface and jointed in neat cement slurry and pointed in white or coloured cement to match pattern approved by Engr-in-Charge complete |
| 57 | M &L 100 mm thick PCC (1 :4:8) type D2 using 40mm agg as in sub base and foundation |
| 58 | M&L Screed bed or bedding layer or mortar 15mm layer of mortar 15mm thick for laying floor finishes in CM 1:6 |
| 59 | M& L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick area of each tile 0.18 sqm but not exceeding 0.38 sqm,, in floors etc. set and jointed in neat cement slurry andpointed in white or coloured cement to match |
| 60 | M&L for 15 mm thick cement plaster on stone /PCC block or concrete surfaces in CM 1:4 complete. |
| 61 | M&L for preparing new plaster surfaces of walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm all as per manufacturers instructions and directed including 10m height steel scaffolding complete all as specified by GE/Engineer-in-Charge |
| 62 | M&L rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 63 | M & L for preparation of newly plastered surfaces & applying three coats of white wash on ceilings complete as spd & directed |
| 64 | M&L for providing precast cement concrete in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match Set in cement mortar 1:6 (Type B1 1:2:4 (20mm graded) complete . |
| 65 | M&L for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing will be painted to match with printed sheed. |
| 66 | M&L for Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 67 | S & F MS butt hinges 100mm size cold rolled medium weight and fixed as directed and specified. |
| 68 | S & F Aluminium handles cast moulded type 150mm size fixed with screws. |
| 69 | S & F Aluminium anodised barrel tower bolts of extruded section, 150mm long as specified. |
| 70 | S&F door sliding bolt aldrop 250 mm long aluminium anodised Make-classic/Shalimar etc equivalent ISI Marked. |
| 71 | S&F 15mm size fancy type chromium plated Bib taps, castcopper alloy with crutch or butterfly handle, screwed down, screwed foriron pipe or forbrass ferrule and fixed |
| 72 | S&F 15 mm size stop valve or angle valve cast copper alloy, chromioum plated fancy type, screwed down, high pressure with capston head, screwed both ends for iron pipe or for union all as specified and as directed. |
| 73 | S&F PVC connections 15mm size with PTMT nuts of length 750mm |
| 74 | S & F liquid soap container of PTMT fixed with and incl chromium plated brass screws and wooden/ plastic cleats. |
| 75 | S & F tubular towel rail, aluminium anodised 20mm dia D type 60 CM long between flanges. |
| 76 | S&F LED looking mirror with smart sensor size n exceeding 0.36 sqm of selected quality Complete all as specified and as directed by Engineer- in- Charge. |
| 77 | S & F 20 mm size gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including taking down old gate valve all as specified and as directed. |
| 78 | Supplying and laying of 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified |
| 79 | S&F vitreous china white wash hand basin 550 mm x 450 mm including all necessary fitting such as 15 mm CP pillar cock fancy type, CP waste coupling 32mm dia, PVC waste pipe and brackets including supply and grouting 6 to 8 mm dia GI racket bolt at the back side of WHB and making good existing surfaces, including taking down old wash hand basin complete all as specified and as directed. |
| 80 | S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe complete. |
| 81 | M&L for Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified. |
| 82 | S&F PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket incl taking down of old EWC with flushing cistern etc complete all as specified and directed . |
| 83 | S&F PVC (SWR) pipes 75mm bore single socketed in any length with ruber ring joints fixed to wall. |
| 84 | S&F PVC (SWR) pipes 110mm bore single socketed in any length with ruber ring joints fixed to wall. |
| 85 | S&F PVC (SWR) bend 75mm bore any redious with access door |
| 86 | S&F PVC (SWR) 110mm bore branch piece, single (Single 'Y') equal or with acess door. |
| 87 | S&F PVC (SWR) 110mm bore WC connector with lip type ring |
| 88 | S&F PVC (SWR) 110mm bore in mm vent cowl. |
| 89 | S&F PVC (SWR) 75mm diameter out let in mm floor trap, plain with grating including jointing with solvent cement. |
| 90 | S&F grating doom grating doom 100 mm dia with waste hole of PTMT (Minimum weight 25 gms) |
| 91 | M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement |
| 92 | Supply and fix 500 litres capacity, rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with 25mm dia GI tank nipple of for inlet, outlet, washout and overflow float valve etc complete all as specified & directed. |
| 93 | S&F Structural steel works as in tubular roof trusses, purlins, vertical posts, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular pipe, channel or flat sections) including distance pieces, cleats , MS plate, riveting incl bending and welding, conforming to Fe – 410W Gde E -- 250 quality A complete all spd and as directed. |
| 94 | S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 95 | M&L for DWCPE (SN8) 200 (OD)/175(ID) mm diameter pipes laid on 150mm thick PCC bad 1:4:8 with excavation in any type of soil at and at depth 0.7m-1.65m deep , incl manholes /drop manhole of standard size made of Brick masonry/RCC with SFRC ventilating cover and frame. includes all items and activities to execute and make sewer line functional. |
| 96 | Cutting into existing manholes for connecting new drains,making good to pipe and rendering,cutting of existing benching for and forming branch channel 1/2 round or 3/4 section in PCC 1:2:4 ,type B-1 forming existing drain making good to walling and rendering cutting out branch channel and making good benching for 300 mm bore pipe. |
| 97 | M&L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 volts grade ISI marked drawn in pvc conduit including provn of 1.5 sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed as earth wire continuity with new plastic laminated white coloured top sheet cover 3.0 mm thick on existing sunken box complete as specified and directed. |
| 98 | One light point controlled by one, one way switch single pole piano type |
| 99 | One Fan point controlled by one, one way switch single pole piano type |
| 100 | One 3 pin 5 Amps socket out let on independent board |
| 101 | M&L for fixing in wall/surface by grinding or wall cutting and making wall/surface good finish of modular metal surface type flush box of module 3 flush ISI marked all as specified and directed. |
| 102 | All as per item No 104 but of 6 module |
| 103 | M&L modular white cover plate with frame of module 3 flush ISI marked all as specified and directed. |
| 104 | All as per item No 106 but of 6 module |
| 105 | M&L for Wiring for circuit/submain/point wiring alongwith earth wire with the following sizes of FRLSH is PVC insulated copper conductor, single core cable in existing surface/recessed as required Note: When wiring is used for point wiring with two conductor wire no extra payment given for connection with switch, socket, regulator, holder, tubelight, fans, etc). |
| 106 | 2x2.5 sq. mm + 1x2.5 sq. mm earth wire |
| 107 | 2x4.0 sq. mm + 1x4.0 sq. mm earth wire |
| 108 | Supply and Fix energy saving, evironment friendly, long life, corrosion resistent, impact proof, Mini LED building security light made up of pressure die cast housing with prismatic polycarbonate diffuser and individual LEDs with secondary optics and IP 65 protection with LED 25 W light source all as per specified by Eng-in-Charge including material and labour for suitable bracket made of 20 mm dia light grade GI pipe & MS clamps complete with nuts and bolts and washers all as specified and directed by Engineer-in-Charge. |
| 109 | Supply and Fixing wall mounted decorative ultra slim LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient ready to use pack instant start with uniform light distribution 20 W 4 ft indoor decorative with 2 Core copper wire from ceiling rose to light fitting as per all as directed by EIC. |
| 110 | S&F modular swicth, 6 Amp flush type 1 module all as directed/ specified. |
| 111 | S&F modular socket, 6 Amp 2/3 pin combined 2 module all as directed/ specified. |
| 112 | S&F of Ceiling rose 3 phase, PVC/ Polycarbonate body all as directed/ specified. |
| 113 | S&F distribution board (DB) , single door type made out of sheet metal enclosure (CRCA sheet) dust and vermin proof DB , SPN 4 way with 200 Amps rated copper bus bar , 240 Volts with in built MCB 32 Amps , 16 KA , 1 No. earth bar IP 43 protection, fix flush to wall complete all as specified and directed. |
| 114 | S&F of isolator/MCBs in distribution board of the MCB SP of 240 volts 5-40 Amps Capacity, 'C' series, 10 KA capacities complete |
| 115 | Supply and Fixing of metal body exhaust fan, AC single phase 230/240V of size 250 mm sweep with louvers and provn of wire mesh for suitable size to cover hole with net frame including making hole of suitable size/ Alteration to the existing hole to fix the Exhaust fan all as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 116 | Supply and Fixing of metal body exhaust fan, AC single phase 230/240V of size 250 mm sweep with louvers and provn of wire mesh for suitable size to cover hole with net frame including making hole of suitable size/ Alteration to the existing hole to fix the Exhaust fan all as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender