Tender For Construction Work Of The National Informatics Centre (Nic) Video Conferencing Hall In The Collectorate Premises
Tender Value
35 Lakhs
Estimated cost
Bid Submission
05 Nov 2026
5 days left
EMD
3.50 Lakhs
Bank guarantee accepted
Document Fee
944
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Auraiya → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Work Of The National Informatics Centre (Nic) Video Conferencing Hall In The Collectorate Premises
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled Jand neatly dressed. All kinds of soil |
| 2 | Sand filling in plinth and under floor including supply of necessary quantity of sand from a distance not exceeding 8 Kms. from the site of work and including watering, dressing etc. labour and T&P etc. required for proper complition of the work saplings of girth upto 30 cms measured at a height of 1 M. above ground level and removal of rubbish upto a distance of 50 M. out side the periphery of area cleared. including cost of sand. |
| 3 | Concrete with 2 cm gauge stone ballast and coarse sand of and cement in proportion and cement in proportion of 6:3:1 in foundation and under floors, including suply of all material, labour & T&P etc. required for proper completion of the work |
| 4 | Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrier under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor, along the the external perlineter of binding expansion joints, surrounding of pipes and conduits etc, complete (plinth area of the building at ground floor only shall be measured as per I.S.6313 (Part II 1981) Alderine emulsifiable concentrate or any other approved material such as Heptrachlor or chordancewill be used. The rate of application of chemical emulsion shallbe as follows: (1 Treatment for masonary & foundation 5 liters per/100 Sqm. (2) Back fill in immediate contact with foundation 7.5 liters/100 Sqın. (3) Treatment of top surface of plinth filling 5 liters / 100 Sqm. (4) Treatment junction of wall and the floor 7.5 liters 100 Sqm. (5)Treatment of soil along external perimeter of building 7.5liters/10 Sqm. (6) Treatinent of soil under apron along external perimter 5 liters / 100 Sqm. |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work, using coradse aggregate and fine aggregate derived from natural sources, portland/pozzolona/ordinary portland/ portland slag cement, admixture in recommonede proportion as per IS:9103 to accelerate/ retard setting of concrete to improve durability and workability without imparing strenght including pumping of concrete to site of laying, curing, carriage for all leads but excluding the cost of centering. shuttering, finishing and reinforcement as per direction of engineer-in-charge Concrete of M25 grade with minimum cement 350kg/cum (Foundation) footings & Column upto Plinth Level |
| 6 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work, using coradse aggregate and fine aggregate derived from natural sources, portland/pozzolona/ordinary portland/ portland slag cement, admixture in recommonede proportion as per IS:9103 to accelerate/ retard setting of concrete to improve durability and workability without imparing strenght including pumping of concrete to site of laying, curing, carriage for all leads but excluding the cost of centering. shuttering, finishing and reinforcement as per direction of engineer-in-charge Concrete of M25 grade with minimum cement 350kg/cum (Super structure) |
| 7 | Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. (Make TATA/JINDAL/SAIL or Approved by Enc.) |
| 8 | Centering and shuttering including strutting, propping etc and removal of form for: Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete ( Foundation to plinth level) |
| 9 | Centering and shuttering including strutting, propping etc and removal of form for (Super Structur) |
| 10 | First class brick work in 1:6 cement and COARSE sand of mortar in foundation plinth including supply of all materials, labour and T&P etc. required for proper completion of work. 9\\" brick work (Foundation to plinth level) |
| 11 | First class brick work in 1:4 cement and COARSE sand of mortar in super structure including supply of all materials, labour and T&P etc. required for proper completion of work. 9\\" thick wrick work (Super structure) |
| 12 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.00% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20nım thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm |
| 13 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to 1S: 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fune Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 14 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with cement slurry and pointing with white cement siurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 15 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 16 | 12 mm cement plaster (1 Cement: 3Coarse Sand) in single coat on fair side of single or half brick wall for interrior plastering includign arises, interior rounded angles chamfers and of rounded angles not exceeding 80 mm in girth and finished even and smooth. As per St 10 |
| 17 | Washed stone grit plaster on exterior walls, in two layers, under layer 12mm cement plaster 1:4 (1 Cement:4Coarse Sand) furrowing the under layer with scartching tool applying cement slurry on th eunder layer @2kg cement per sqm, top layer 15mm cement plaster 1:1/2:2, in panels with grooves all around as per approved pattern including scubing and washing the to top layer with brushes and water to expose the stone chipping, complete as per the specifications and direction of engineer in |
| 18 | Forming grroves of uniform size in the tiop layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repairs to the edges of panels and finishing the groove complete as per specification and direction of the engineer in charge: 15mm wide and 15mm deep grooves. 2m x2m panel |
| 19 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 20 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 21 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). |
| 22 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Sal wood |
| 23 | Providing and fixing ISi marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Providing & Fixing decorative high pressure laminated sheet of plain I wood grain in gloss matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 Type S, including casta |
| 24 | Providing and fixing factory made UPVC three track white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mun thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of UPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, |
| 25 | Providing and fixing Stainless steel sliding bult, SS 304 grade marked, transparent or dyed to required colour or shade, with necessary screws etc. complete :(250x16mm) |
| 26 | Providing and fixing Stainless steel tower bolt, 55 304 grade marked, transparent ur dyed to required colour or shade, with necessary screws etc. complete: (250x10mm) |
| 27 | Providing and fixing Stainless steel door handle, SS 304 grade marked, transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm long |
| 28 | Providing and fixing false ceiling with 12 mm thick plain/semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to 15:3087, finished with a coat of aluminium primer on both sides & edges including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodised aluminium (with 15 micron anodic coating) T-sections 35 x15x1.5 mm size main runners and cross runners 23.5x19x1.5 mm fixed to main runners placed 600 min centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminium frame work shall be paid separately). |
| 29 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary Jaccessories and screws etc. complete. |
| 30 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:. 75x45x3.2 mm |
| 31 | Providing and laying \\"brick coba\\" 12 mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finfished smooth & top mashed false square 30 x 30 cm and side wall parapet shall be monotythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand masonary coba with top finished plaster mixed with acetic water proofing compound 2% by weight & including S/o all material, labour, T&P etc complete for proper completion of work. |
| 32 | ACP Wali Pannelling Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender