Tender For Installation And Energisation Of Ghuna-V L.I.P. Under Gudvella Block (Bkvy Ridf 2026-27)
Tender Value
61.63 Lakhs
Estimated cost
Bid Submission
13 Nov 2026
10 days left
EMD
61631
Bank guarantee accepted
Document Fee
11800
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Balangir → Odisha
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Installation And Energisation Of Ghuna-V L.I.P. Under Gudvella Block (Bkvy Ridf 2026-27)
BOQ
| Sl. No. | Item Description |
| 1 | Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge. |
| 2 | Earthing in excavation of foundation in hard soil such as hard stiff clay black cotton hard red earth ,shales ,maoorum ordinary gravels etc within 50m. Initial lead and 1.5m. Initial Lift including rough dressing and levelling the bed and depositing the excavated materilas within initial lead at nearby the worksite for reuse including breaking clods and stacking rubble for spreading and leveling as the case may be etc complete as per direction of the Engineer-in- charge . (I) Excavation by mechanical means with excavator of bucket size 0.6 m |
| 3 | Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge. |
| 4 | Filling the foundation and plinth with excavated material as directed by the Engineer-incharge.(a) Manually |
| 5 | (b) Machinery for pipe line work |
| 6 | Cement concrete (1:4:8) with 4cm size h.g.b. hand broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc. complete as per the direction of the Engineer-incharge. |
| 7 | Brick work with fly ash Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerance + 8% in cement mortar (1:6) in foundation & plinth etc. complete as per the Engineer-in charge. |
| 8 | Brick work with fly ash Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in super structureetc. complete as per the Engineer-incharge. |
| 9 | Cement concrete (1:2:4) with 12mm size black C.B. hand broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P required etc complete as per the direction of the Engineer-incharge. |
| 10 | Rigid smooth centering & shuttering for R.C.C. works including false work & dismateling then after including cost of materials in ground floor complete an directed by the Engineer-incharge. a) Plinth Bend, |
| 11 | b) Lintel |
| 12 | c) Chajja |
| 13 | d) Column |
| 14 | Labour charge for M.S. reinforcement for R.C.C. work including cutting, bending & typing the grills & placing in position including cost of binding wire 18 to 20 guage per Qntl. Including cost of HYSD Steel Bar (FE 415/ FE 500) |
| 15 | R.C.C. work in C.C. (1:2:4) including hoisting & laying & curring for 28 days using 12mm. Size clean black hard granite crusher broken chips of approve quality and from approve quarry including cost taxes conveyance charges of all materials to the worksite with supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 16 | 12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 17 | 20mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 18 | Cement punning over plastering including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required for the work etc complete as directed by the Engineer-incharge. |
| 19 | Writing charge of required information and data on both side of the transperancy pillar & in wall of Pump Chamber including supplying of approved paints and required material for writing etc. complete as per the direction of the Engineer-incharge. |
| 20 | White Washing 2 coat with stone lime |
| 21 | Distempering 2 coat over a coat of white washing with approve good stone lime and colouring material includingcost conveyance charges of materials includng supply of labour, gum,indigo etc. requiredfor the work complete as directed by the engineer in charge. |
| 22 | M.S. pannel door single leafed with M.S. frame overall size includingframe of height (1.2 x2.0)mt. width for door and shutter of 18 gauge CR sheet pannel as per approved size & specification etc. complete including cost of all materials fitting and fixing the door etc. complete as per the direction of the Engineer in charge. |
| 23 | M.S. pannel window single leafed with M.S. frame overall size includingframe of height (0.9 x2.0)mt. width of 18 gauge CR sheet pannel as per approved size & specification etc. complete including cost of all materials fitting and fixing etc. complete as per the direction of the Engineer in charge. |
| 24 | Suplying fitting and fixing of sky light of approved quality of size 0.60 mtr. X 0.38 mtr. Made ofcement concrete as per the direction of the Engineer in charge. |
| 25 | 25mm thick A.S. flooring with C.C. (1:2:4) using 12mm size black hard granite crusher broken chips of approve quality for approve querry including water and curring with cost taxes royalty and conveyance charges of all material toworksite and supply of all labour and T&P required for the work complete as directed by the Engineer in charge. |
| 26 | Pump chamber wiring with plug and light arrengment |
| 27 | Painting two coat with an approve primer over iron work including cost of labour etc. complete as per direction of the Engineer in charge. |
| 28 | Cost ,Ṣupplying of ISI Marked High Density Polythelene (HDPE) Pipesfor water supplyas per IS4984/2016 in the following Nominal diameter, Grades of materials, Pressure rating including the rates of ex-factory, transportation, pre & post inspection, cess etc complete but excluding the cost of GST (a) 250mm dia. HDPE Pipe PE 100-PN 6 |
| 29 | (b) 160 mm dia. HDPE Pipe PE 80-PN 4 |
| 30 | Supplying all materials, labour,T&P for jointing of 250 mm outer dia. High Density Polythylene Pipes of specific material grade & pressure rating by butt fudion welding method as per specification & laying in trenches including testing including all cost etc complete as per direction of the Engineer-in charge |
| 31 | Supplying all materials, labour,T&P for jointing of 160 mm outer dia. High Density Polythylene Pipes of specific material grade & pressure rating by butt fudion welding method as per specification & laying in trenches including testing including all cost etc complete as per direction of the Engineer-in charge |
| 32 | 12.5/15.00 HP Centrifugal Monoblock pumpset 24mtr. Head to discharge 0.0283 Cumec (Powder coated) |
| 33 | Control Panel Board with 12.5 /15.00 HP Starter, Capacitor including internal wiring with MCB, Indicator lamp & Volt meter, Ameter etc. |
| 34 | Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red oxide primer and two coats of smoke gray / navey blue enamel n both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board. |
| 35 | Base frame for panel (size 0.40mx0.20m) made with 3\\" size M.S. channel having suitable holes for fitting of panel Board, coloured with one coat of red oxide primer and two coats of smokes grey enamel paint & Base frame for motor (size 0.50mx0.27m) made with 3\\" size M.S. channel having suitable holes for fittings of different size and make 3 phase centrifugal monoblock pump set from 10 H.P. to 15 H.P. coloured with one coat of red oxide primer & two coats of smoke grey enamel paint. |
| 36 | Cost of Empty out door irrigation Pannel box(size 0.45X0.25X1.20m) |
| 37 | Cost of 6KVAR Capacitor |
| 38 | Cost of Foundation nut & bolts. |
| 39 | Cost of Outlet of RCC 'T' Tank |
| 40 | Cost of Labour charges for instalation of Pump Set, Suction, Delivery Pipe, G.I. Pipe, G.I. Fittings, Base Plate including cost of required Nut Bolt, Rubber Packing, Cutting & Threading of G.I. Pipe Welding, Fitting of Butterfly Valve and for Priming arrangement etc.complete. |
| 41 | 3 x 16 sqmm Tarpodar cable XLPE (Cross link polyethylin) conforming to IS: 7098 (Part-II) including laying below .9mtr. of the ground and filling the excavated materials including watering and ramming. |
| 42 | 100 mm Ø nominal bore G.I. pipe having wall thickness 4.5 mm electrical resistance welded of medium class confirming to IS - 1239 (pt-1 of 2004) with socketed at one end and the other end protected with plastic thread protector. The socket confirming to IS-1239 (pt-II/1992) with latest amendmewnts in random length of 4 to 7 mtrs. Each pipe should bear ISI certification & manufacturers name / Trade mark. |
| 43 | 100 mm Ø C.I. Foot Valve should be of swing type friction less with single disc confirming to IS – 4038/1979 of reputed brand |
| 44 | 100 mm dia G.I. flange IS No.6392 / 1971 |
| 45 | 100 mm dia G.I. bend IS No.1239(Part-II/1992) |
| 46 | 100mm Non-return valve C I double flanged swing type PN - 1.0 as per IS:5312 part-I with by-pass arrangement |
| 47 | 50 mm Ø Air release valve with saddle & Raiser pipe. The air release valve shall confirm to IS 14845 with ISI mark. |
| 48 | 100x100x50mm G.I. priming Tee |
| 49 | 273 mm M.S. pipes with plain ends in random length of 4 to 7 mtrs. Confirming to BIS 3589 with minimum wall thickness of pipes should be 5.5 mm each pipe should bear ISI specification and manufacturers name / Trade mark. Steel grade of the pipe should be Fe330 |
| 50 | Cost of welding,laying & fitting of 273 mm dia. M.S pipe |
| 51 | 250 X160 MM HDPE Reducer |
| 52 | 250mm X 100mm x 100mm M.S.Y fabricated with accessories |
| 53 | 250 mmx 250 mmX 160mm dia HDPE Tee with all fittings |
| 54 | 160 mm x 160 mm x100 mm Ø M.S.Raiser Tee set with bend , closing and opening arrangement. |
| 55 | Cost of Butterfly Valve with all fittings |
| 56 | 273 mm dia MS Flange |
| 57 | 250 mm Ø HDPE End Cap |
| 58 | 160 mm Ø HDPE End Cap |
| 59 | 160x160x160 mm dia HDPE equal Tee |
| 60 | Electrical installation including labour charges of Control chamber wiring, fitting of all electrical equipment with help of back light board including all required petty purchase materials fitting & fixing of danger board, energy meter, laying of T.d. cable including power supply & commissioning etc. 1 Set |
| 61 | Earthing with help of 1½\\" dia G.I. Pipe 2 Nos. incuding all baour and required materials such as G.I. Wire G.I. Socket, Charoal, Salt, small size nut & bolts and all other materials required including excavation of earth pit & fitting thereof in complete - 1 No. |
| 62 | Construction of 3 Phase 11 KV HT line as per REC standard To IEEE Rule 1956 with 300 KG 10Mtr long PSC pole with 55Sqmm AAA Conductor averafge span 40 mtr ,11 KV \\"V\\" corss arm required no. of 11Kv T&C Disc . Polymer insulators, couping & padding of poles with all G.I Channels, Danger Board at each pole, anti Climbing Device ,stay set at Bending Point & Double Stay at end point with 18mm GI HT stay with anchor plate , guarding at road crossing etc if required including cost of all materials, labour transportation ,inspection & commissioning etc . complete |
| 63 | Construction and errection of 11/0.4 KV ,63 KVA Double pole mounted substation with 14.76ft*9.84ft*6ft height mesonary Economic Brick Wall Fencing with flat polymer insulator , Lt dist Box with MCCB , aluminium bus bar of single bay with kit kat fuse ,sand filling and metal spearding with M.S grill gate . all Channel material should be GI , 7 nos earthing with chamber with 3mtr G.I pipe of 40mm dia with connecting of 25mm*5mm GI flat to all earthing including 63KVa BIS level -II star rated TF confirming to RE rule 1956, mountyed on 2.44 mtr long structure, supported in 330 KG 10 mtr long PSC pole, transformer hard channel & top channel made of 2.8 mtr long 100*50*6 mm GI channel transformer belting on 2.8 mtr long 50mm*50mm*5mm G.I angle(all REC SPN std.F-3) with all accessories like 3 pole 11kv HG fuse (F-5) & A.B Switches (F-9) both mounted on 2.8 mtr long 75*40*6mm GI channel and Support by 1mtr long 50*50*5mm GI angle ,with 3No 11KV lightening Arrestor and Danger Board at each pole ,anti climbing devices and all other necessary fitting i.e required size nuts & bolts , Brackets ,Cable, Cable socket as per TPWODl specification etc, including cost of all material ,labour ,transportation complete with liasioning for testing inspection & commissioning as per specification of TPWODL etc . complete. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender