Tender For Renovation & Maintenance Of Gymnasium Hall At Nsrcc, Agartala/Sh: Gypsum Board, Plastering, Wood Work, Rain Water Pipes, Sanitary Fittings, Bamboo Flooring & Walling And Other Allied Works During The Year 2026-27
Tender Value
80.46 Lakhs
Estimated cost
Bid Submission
10 Nov 2026
9 days left
EMD
1.60 Lakhs
Bank guarantee accepted
Document Fee
4000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation & Maintenance Of Gymnasium Hall At Nsrcc, Agartala/Sh: Gypsum Board, Plastering, Wood Work, Rain Water Pipes, Sanitary Fittings, Bamboo Flooring & Walling And Other Allied Works During The Year 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Without dewatering:- Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material. |
| 2 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200. i) sand filling |
| 3 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m. |
| 4 | Clearing jungle including uprooting of rank vegetation, grass, brushwood, treesandsaplingsofgirthupto30cm measured at a height of 1mabove ground level and removal of rubbishuptoadistanceof 50moutside the periphery of the area cleared |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering (a) 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate 20 mm nominal size) |
| 6 | Providing concrete for plain concrete (using jhama brick aggregate) in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement) P.C.C M10 i ) Nominal mix 1:3:6 (hand mixing) |
| 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 8 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 9 | Centering shuttering including struttings, propping etc. and removal of form work for:Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply |
| 10 | First class brick work in super structure above plinth level & upto floor-five level including cost of all materials as required complete : In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 11 | Half brickmasonryworkwith first class bricks in superstructureuptofloor five level includingcostof all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 12 | 12 mm cement plaster of mix : Cement mortar 1:6 (1 cement : 6 fine sand) |
| 13 | 15mm cement plaster on the rough side of single or half brick wall of mix: Cement mortar 1:6 (1 cement : 6 fine sand) |
| 14 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge. |
| 15 | Providing and fixing to existing door frames.30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 110mm width out of which 90mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 110mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on the inner side to form top and bottom rail and 130mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-incharge, manufacture’s specification & drawing. |
| 16 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and anufacture on old work ( one or more coats ) including preparation of surface as required complete as per direction of the Engineer in charge. |
| 17 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Local Teak Wood |
| 18 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 19 | Painting with synthetic enamel paint ( one or more coats ) of required colour of approved brand and manufacture on old work to give an even shade including preparation of surface as required complete as per direction of the Engineer in charge. |
| 20 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:Single socketed pipe - 110 mm OD |
| 21 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion::Single socketed pipe - 75 mm OD |
| 22 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: |
| 23 | Coupler |
| 24 | 75 mm |
| 25 | 110 mm |
| 26 | Single equal tee without door |
| 27 | 75x75x75 mm |
| 28 | 110x110x110mm |
| 29 | Bend 87.5° |
| 30 | 75 mm |
| 31 | 110 mm |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 33 | 15 mm nominal outer dia .Pipes. |
| 34 | 20 mm nominal outer dia .Pipes. |
| 35 | 25 mm nominal outer dia .Pipes. |
| 36 | 40 mm nominal outer dia .Pipes. |
| 37 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stabilityfor hot&coldwatersupplyincludingallCPVCplain& brassthreadedfittingsThisincludesjointingofpipes & fittings with one step CPVC solvent cement ,trenching ,refilling&testing of jointscompleteas per direction of Engineer in Charge. External work40 mm nominal outer dia .Pipes. |
| 38 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap |
| 39 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of430x260x350mm and 340x410x265mm sizes respectively. |
| 40 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete: Semi rigid pipe |
| 41 | 32 mm dia |
| 42 | 40 mm dia |
| 43 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 44 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 45 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity-White |
| 46 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :White solid plastic seat with lid |
| 47 | Providing and fixing PTMTBall cock of approved quality, colour and make complete with Epoxycoated rod with L.P./ H.P.H.D. plastic ball. 40mmnominal bore, 206mmlong, weighingnot less than 690gms. |
| 48 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mmthick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 49 | Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angleframe with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 50 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore |
| 51 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 52 | Providing and fixing PTMT urinal cock of approved quality and colour : 15 mm nominal bore, 80mm long. 42 mm high and 30mm wide with BSP female threads weighing not less than 48gms |
| 53 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved quality and colour.600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 54 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. : Fixed to steel windows by welding. |
| 55 | Marble work gang saw cut (polished and machine cut) of approved thickness for wall lining (veneer work), backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 fine sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the marble shade: (to be secured to the backing by means of cramps, which shall be paid for separately), including rubbing, curing etc. complete at all levels as required:- 14 mm thick Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble or equivalent duly approved: Area of slab over 0.50 sqm. |
| 56 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622- 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge.450 mm X 300 mm in all shades and design |
| 57 | Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.Kota stone slab 25mm thick |
| 58 | Providing and fixing ISI marked oxidised M.S.pressed butt hinges with necessary screws etc. complete.125 × 65 × 2.12 mm |
| 59 | Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. complete300×16 mm |
| 60 | Providing and fixing ISI marked oxidised M.S.handles conforming to IS:4992 with necessary screws etc. complete :125 mm |
| 61 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type)with necessary screwsetc. complete : 250x10 mm |
| 62 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc.complete. |
| 63 | Providing and fixing IS:3564 marked Aluminium die cast body tubular type universal hydraulic door closerwith necessary accessories and screws etc. complete. |
| 64 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :For fixed portion of approved quality:Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 65 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 66 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 67 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 68 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of specialsections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mmhigh having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/ partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes ,finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as perdrawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part I. |
| 69 | Providing & fixing in position Phenol bonded Bamboowoodflooringwithplanksofsizes14mmthick, 1800mmlength(minimum)and130mmwide(minimum), in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council(BMTPC). The flooring shall be fixedwith tongue and grooveinterlockingsystem,withunderlaymentof4mmthick expanded poly ethylene foam sheets having density40kg/cum,overpreparedsurfacewithnecessaryquarterroundplanksofsize1900mmx18mmanddoor reducer of size 1900mmx 44mm, wherever required.Thebomboowoodplanksshall haveminimumdensity of 1000Kg/cum&minimumHardness1000Kgf.withEcofriendlyUVcoating,etc.allcompleteasperdirection of Engineer-in-charge. |
| 70 | Providing& fixing inpositionPhenol bondedBamboo woodinwall skirtingwithplanksofsizes14mmthick,1900mmlength (minimum) and85mmwide(minimum), in approved colour, texture and finish, havingPerformance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council(BMTPC). The skirting shall be fixedwithSS screws& rawlplugs, overunderlaymentof4mmthick, expandedpoly ethylene foamsheets having 40kg/cum density overpreparedsurface. Thebomboowoodplanks shallhaveminimumdensity of 1000 Kg/cum&minimum Hardness1000Kgf.withEcofriendlyUVcoating,etc.allcomplete as per direction of Engineer-in-charge. |
| 71 | Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross- T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm oflength 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of Engineer-in Charge.: With semi perforated12mmthickmicro tegular edged GRG false ceiling tiles. |
| 72 | Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 73 | Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti-termite treatment as per IS: 6313(Part III)- Latest revision (excluding the cost of chemical emulsion):Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45° at 150 mm centre to centre and sealing the same. |
| 74 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective ofduration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 75 | Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 76 | Demolishing reinforced cement concrete manually / by mechanical means including stacking of steel bars properly and disposal of unserviceable material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge. |
| 77 | Demolishing brick work including stacking of serviceablematerialsanddisposal ofunserviceable materialswithall liftsanduptoa leadof 50metc. complete as per direction of the Engineer- in-charge:In cement mortar. |
| 78 | Dismantlingdoors,windowsandclerestorywindows (steel or wood) shutter including chowkhats, architrave, holdfasts etc.complete and stacking within 50 metres lead :Of area 3 sqm and below. |
| 79 | Dismantlingwoodwork in frames, trusses, purlins and rafters upto10metres span and 5metre sheight including stacking thematerialwithin50metreslead: Of sectional area 40 sq cm and below. |
| 80 | Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plasteringor re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 81 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 82 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 83 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm |
| 84 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender