Tender For Renovation Of Open Space Above Gps Room At Nagpur Ahq Under Nagpur Area. E-
Tender Value
13.46 Lakhs
Estimated cost
Bid Submission
10 Nov 2026
11 days left
EMD
16900
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagpur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Open Space Above Gps Room At Nagpur Ahq Under Nagpur Area. E-
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulicexcavator)/manual means over areas (exceeding 30 cm indepth, 1.5 m in width as well as 10 sqm on plan) includinggetting out and disposal of excavated earth lead upto 50 mand for all lift, as directed by Engineer-in-charge. All kinds of soil |
| 2 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 3 | Providing and laying in position specified grade of reinforcedcement concrete, excluding the cost of centering, shuttering,finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3graded stone aggregate 20 mm nominal size derived from natural sources) |
| 4 | Providing and laying in position cement concrete ofspecified grade excluding the cost of centering andshuttering - All work up to plinth level : 1:1½:3 (1 Cement:1½coarse sand (zone-III) derived fromnatural sources: 3 graded stone aggregate 20 mm nominalsize derived from natural sources) |
| 5 | Centering and shuttering including strutting, propping etc. And removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 6 | Providing and fixing mild steel round holding down boltswith nuts and washer plates complete. |
| 7 | Structural steel work in single section, fixed with or withoutconnecting plate, including cutting, hoisting, fixing inposition and applying a priming coat of approved steelprimer all complete. |
| 8 | Demolishing R.C.C. work manually/ by mechanical meansincluding stacking of steel bars and disposal of unserviceablematerial within 50 metres lead as per direction of Engineer -in- charge. |
| 9 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and stringcourses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3graded stone aggregate 20 mm nominal size derived from natural sources). |
| 11 | Centering and shuttering including strutting, propping etc. And removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts |
| 12 | Centering and shuttering including strutting, propping etc. And removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth Level.Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 14 | Demolishing brick work manually/ by mechanical meansincluding stacking of serviceable material and disposal ofunserviceable material within 50 metres lead as per directionof Engineer-in-charge. In cement mortar |
| 15 | Brick work with clay flyash F.P.S. (non modular) brick of classdesignation 7.5 in superstructure above plinth level up tofloor five level in : Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 16 | Half brick masonry with common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 in superstructureabove plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarse sand) |
| 17 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) |
| 18 | Providing and applying plaster of paris putty of 2 mmthickness over plastered surface to prepare the surfaceeven and smooth complete. |
| 19 | Distempering with 1st quality acrylic distemper (readymixed) having VOC content less than 50 gram/litre, ofapproved manufacturer, of required shade and colour allComplete: New work (two or more coats) over and including water thinnable priming coat with cement primer having VOCcontent less than 50 pram/litre |
| 20 | Finishing walls with Acrylic Smooth exterior paint ofrequired shade . New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm |
| 21 | Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS: 15622,of approved make, in all colours and shades, laid on20mm thick cement mortar 1:4 (1 cement : 4 coarsesand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement andmatching pigments etc., complete. Size of Tile 1000x1000 mm |
| 22 | Providing and laying Vitrified tiles in different sizes(thickness to be specified by manufacturer), with waterabsorption less than 0.08 % and conforming to I.S. 15622,of approved make, in all colours & shade, in skirting, riserof steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry@ 3.3 kg/ sqm including grouting the joint with whitecement & matching pigments etc. Complete. Size of Tile 1000x1000 mm |
| 23 | Providing and fixing M.S. grills of required pattern inframes of windows etc. with M.S. flats, square or roundbars etc. including priming coat with approved steelprimer all complete. Fixed to steel windows by welding |
| 24 | a)Supplying and fixing in position Aluminium four track sliding windows with outer frame made from sectionofoverallsize122mmx45mm,bottomsectionwithdrainsectiontrackweighing1.83Kilogrampermetreandtopandsidesectionofsize122x31.75mmweighing1.15KilogramperOneRunningMetrewithshuttersectionsmadeof18mmx40mmsizehavingaverageweightof0.6KilogramperOneRunningMetre(orasrequiredsize)withchangeinproportionateweight,with6mmfloatglassinthreeequalpanelsandalluminiumcoatedstainlesssteelmosquitonetinone(2/3ofopening)panelfixedwithnewneoprenegasket,shutterstobeprovidedwithnylonencasedstainless steel rollers, necessary locks and handles complete. a) Colour anodized |
| 25 | Providing and fixing ISI marked flush door shuttersconforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1st classhard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and faceveneers on both faces of shutters: 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 26 | Extra for Providing and fixing flush doors with decorativeveneering instead of non decorative ISI marked flushdoor shutters conforming to IS: 2202 (Part I) On one side only |
| 27 | Providing and fixing ISI marked oxidised M.S. slidingdoor bolts with nuts and screws etc. complete : (copperoxidized as per IS: 1378) 300x16 mm |
| 28 | Providing and fixing ISI marked oxidised M.S. handlesconforming to IS:4992 with necessary screws etc.complete : (copper oxidized as per IS: 1378) 125 mm |
| 29 | Providing and fixing T-iron frames for doors, windows andventilators of mild steel Tee-sections, joints mitred andwelded, including fixing of necessary butt hinges andscrews and applying a priming coat of approved steelPrimer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominalSize). |
| 30 | Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade : Two or more coats on new work |
| 31 | Providing and fixing false ceiling at all heights with integraldensified calcium silicate reinforced with fibre and naturalfiller false ceiling tiles of Size 595x595 mm of approvedtexture, design and patterns having NRC (Noise Reductioncoefficient) of 0.50 (minimum) as per IS 8225:1987, Lightreflectance of 85% (minimum). Non combustible as perBS:476 (part-4), fire performance as per BS:476 (part 6 &7),humidity resistance of 100%, thermal conductivity < 0.043W/m K as per ASTM 518:1991, in true horizontal levelsuspended on inter- locking metal powder coated T-Grid ofhot dipped galvanised iron section of 0.40 mm thick onSilhouette profile,rotary stiched double webbed white with6mm reveal profile (white/black),comprising of main-Trunners of size 15x42mm of length 3000 mm, cross - T ofsize 15x42 mm of length 1200 mm and secondaryintermediate cross- T of size 15x42 mm of length 600mmto form grid module of size 600 x 600 mm, suspended fromceiling using galvanised mild steel items (galvanizing @ 80grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6dash fasteners, 6 mm dia fully threaded hanger rod upto1000 mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size22x19x0.40 mm of length 3000 mm to be fixed onperiphery wall / partition with the help of plastic rawl plugsat 450 mm center to center and 40mm long dry wall S.Sscrews. The work shall be carried out as per specifications,drawing and as per directions of the Engineer-in-Charge.With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles |
| 32 | Providing and fixing precoated galvanised iron profilesheets (size, shape and pitch of corrugation as approvedby Engineer-in-Charge) of total coated thickness 0.50mm(base metal of minimum 0.45mm thickness with totalcoating thickness of 0.05mm) with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester topcoat 15-18 microns. Sheet should have protective guardfilm of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto12 metre or as desired by Engineer-in- charge. The sheetshall be fixed using self drilling /self tapping screws of size(5.5x 55 mm) with EPDM seal, complete upto any pitch inhorizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size andshape wherever required. |
| 33 | Steel work in built up tubular (round, square or rectangularhollow tubes etc.) trusses etc., including cutting,hoisting, fixing in position and applying a priming coat ofapproved steel primer, including welding and bolted withspecial shaped washers etc. Complete. Hot finished welded type tubes |
| 34 | Point wiring for light/fan/bell in 20 mm HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire with flush type switch and required accessories as per specification no. WG-PW/SW |
| 35 | Supplying and erecting LED square / circular Max. 25 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuserhaving system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 36 | Providing and erecting air circulator 600 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for 230/250 volts single phase, 50 cyclesA.C. supply, core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation. |
| 37 | Supplying and erecting shockproof 3 pin plug socket 6A with porcelain base/flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3mm thick hylam sheet/ 4mm thick plywood pasted with 1.5mm thick laminate with S M screws and duly connected. |
| 38 | Supplying and erecting shockproof 3 pin plug socket 16A with porcelain base/ flush type erected on filled polypropylene board or polished thick varnished double wooden block / folded or screwed board with top of either wooden/3mm thick hylam sheet/ 4mm thick plywood pasted with 1.5mm thick laminate with S M screws and duly connected. |
| 39 | Supplying, erecting & marking SP MCB 6A to 32A, C-series with rated short - circuitbreaking capacity (Icn) 10kA in provided distribution board as per specification no.SW-MCB |
| 40 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 10, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender