Tender For Provision Of Shed In 750 Kva Mafi Dg Set And 02 No Of Power Distribution Panel Works And Addition / Alteration Of Washroom At Trishakti Dwar, installation Utkrosh Under Ge Minniebay, Sri Vijaya Puram (8875/E8)
Tender Value
47.50 Lakhs
Estimated cost
Bid Submission
20 Nov 2026
19 days left
EMD
95000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Shed In 750 Kva Mafi Dg Set And 02 No Of Power Distribution Panel Works And Addition / Alteration Of Washroom At Trishakti Dwar, installation Utkrosh Under Ge Minniebay, Sri Vijaya Puram (8875/E8)
BOQ
| Sl. No. | Item Description |
| 1 | Excavation post holes (or similar holes) each not exceeding 0.5 cum getting out in soft/loose soil , returnig filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm watering and removing surplus soil to a distance not exceeding 50m and making good surfaces complete all as specified and directed. |
| 2 | Excavation in trenches not exceeding 1.5m wide and not exceeding 10 Sq.m on plan area and not exceeding 1.5m deep in soft/loose soil complete all as specified and as directed. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm using available soil obtained from excavation complete all as specified and directed. |
| 4 | Removal of excavated material [Soil] to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed. |
| 5 | M & L for PCC 1:2:4 type B2(using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 6 | S&F Rolled Mild Steel sections as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) includingdistance pieces, cleats etc(conforming to Fe 410-W (Gde E-250) quality A) complete all as specified and as directed. |
| 7 | S&F Rolled Mild steel sections as in Vertical post, main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates(conforming to Fe 410-W (Gde E-250) quality A) |
| 8 | S&F Plates (Plain or chequred) channels, square cut or notched (ordinary and counter sunk) conforming holes without any attchement ( conforming to Fe 410-W (Gde E-250) quality A) complete all as specified and directed. |
| 9 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as manufacturers instruction and as directed. |
| 10 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as in ridges, hips, valley gutter, drip, and straight flashing complete all as specified and directed. |
| 11 | S & F Aluminium flat iron work in wind ties 40x6mm size fixed with 50/75mm aluminium self staging screws with integral EPDM washer screwed in roof covering including all necessary drilling, bolting or riveting etc., and similar complete all as specified and directed. |
| 12 | S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/ vertical support for rain pipe complete all as specified and directed. |
| 13 | S&F 110mm bore PVC (SWR) bends any radius suitable for PVC (SWR) pipe complete all as specified and directed. |
| 14 | M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width type C-1 (1:3:6) using 20mm graded stone aggregate and setting in cement mortar (1:4) complete all as specified and directed. |
| 15 | M&L for rendering 15mm thick plaster in CM (1:4) on concrete or block masonry surfaces and finishing the surfaces even and fair complete all as specified and as directed. |
| 16 | M&L for PCC (1:4:8) type D2 (using 40mm graded aggregate) 75 mm thick as in subbase of flooring complete all as specified and directed. |
| 17 | M&L for 50 mm thick crushed Sand under paver block including watering and consolidation complete all as specified and as directed. |
| 18 | M & L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 grade complete all as specified and diected. |
| 19 | M&L Providing cement concrete type B-1, 1:2:4 (using 20mm graded aggregate) as in coping, benching, bands, lintels, beam span less than 1.5 mtr length and similar works slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed. |
| 20 | Preparation of New or previously untreated steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of red/zinc oxide primer complete all as specified and directed. |
| 21 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. |
| 22 | Demolition of precast concrete work built in cement mortar including all quoins arches pillars etc., complete all as specified and as directed. |
| 23 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness ( below or above ground level) etc., complete all as specified and as directed. |
| 24 | M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams etc., and mass concrete complete all as specified and directed. |
| 25 | M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in beams, cantilevers, bresuemers, lintels over 1.5m span etc complete all as specified and directed. |
| 26 | M&L RCC M-30 Nominal mix using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts etc complete all as specified and directed. |
| 27 | M&L formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides and soffits of foundation (if any) and plinth beams for rough finished surfaces of concrete, flat, complete all as specified and as directed. |
| 28 | Formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, flat, complete all as specified and as directed. |
| 29 | Formwork to sides and soffits of floor or roof beam, beam haunching, girders, bressum-mers lintels, cantilevers, shelves, including support, overhangs, etc also splays between floors and beam etc complete all as specified and directed. |
| 30 | M&L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 31 | M&L PCC (1:4:8) Type D2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete complete all as specified and directed. |
| 32 | M&L Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed. |
| 33 | M&L for PCC (1:4:8) type D2 (using 40mm graded aggregate) 100 mm thick as in subbase of flooring complete all as specified and directed. |
| 34 | Dismantling floor, hearth or wall tiles including cement mortar bedding (but not backing) and removing serviceable tiles to stores and rubbish off the premises etc., complete all as specified and as directed. |
| 35 | M&L for coloured non-skid ceramic tiles 7 to 8 mm thick exc. 0.06 sqm but n.exc 0.11sqm area of each tiles in floor/ steps etc set and jointed in neat cement slurry and pointed in coloured cement to match as in floor over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed. |
| 36 | M&L for glazed ceramic coloured/printed tiles 450x350x 7mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tile over 10mm thick backing in cement mortar (1:3) complete all as specified and directed. |
| 37 | M&L non skid cermic coloured tiles (400 x 400)mm and 8mm thick ( square or rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm, in floor etc and jointed in neat cement slurry and pointed in white cement or coloured cement to match the shade of tile complete all as specified and directed. |
| 38 | M&L for rendering 15mm thick plaster in CM (1:6) on brick/block or concrete surfaces finished even & smooth complete all as specified and as directed. |
| 39 | M&L for rendering 5mm thick plaster in CM (1:4) over a backing coat of 10 mm thick in CM 1:6 (Total 15 mm thick ) on concrete or block masonry surfaces including mixing water proofing compound on top layer as per manufactures instructions(or 3% by weight of cement) and finishing the top surfaces even and fair complete all as specified and as directed. Note :Water proofing compound shall be measured and paid seperately under relevant item of this schedule as supply only. |
| 40 | Supply only water proofing compound ISI marked complete all as specified and as directed. Note : WPC may apply as per manufactures instruction or 3% by the wt of cement |
| 41 | Dismantling of stone slabs and tiles of any description or thickness in floors, approns and laid bedded and pointed in any mortar etc., complete all as specified and as directed. |
| 42 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM(1:6) etc., complete all as specified and as directed. |
| 43 | Providing and fixing factory made uPVC any colour fixed window made of extruded profiles with wall thickness of 2.3mm(+-0.2mm). Window profile with hollow section with multi chamber. Frame (60mm x 58mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. making arrangement for fixing of hardware, EPDM gasket. 1.2 +–0.2mm thick, galvanized steel Frame (28mm x 21.5mm), T profile (27mm x 17 mrn) to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners- 5mm thick glazing with selected quality glass complete all as specified and directed.Note:- Gap and grooves should be filled with silicon agent |
| 44 | S&F of 6mm thick sheet figured glass pin headed type, not exc 0.50 sqm in each pane, duly fixed with oil putty or wooden bidding as required complete all as specified and directed. |
| 45 | Supply and fixing factory made uPVC any colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws,etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in Charge. (Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 46 | Supply and laying of CPVC pipes 20 mm dia outer bore SDR 11 & plain CPVC SDR 11 fittings on walls /ceilings or laying in floors complete all as specified. |
| 47 | S&F 20 mm bore CPVC Brass Elbow |
| 48 | S&F 20 mm bore Brass Elbow reducer(3/4 x1/2) |
| 49 | S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/MBTA) |
| 50 | S&F 20 mm bore CPVC Female Brass Threaded Adaptor (FTA/FBTA) |
| 51 | S&F 20 mm bore CPVC Brass Tee |
| 52 | S&F 20mm bore CPVC Brass Union |
| 53 | S&F 25mm dia aluminium anodised best quality curtain rod alongwith brackets long body in pairs fixed both ends (rates included of brackets) complete all as specified and as directed. |
| 54 | S&F in repair Vitreous china white heavy duty Counter Top wash hand basin of 520x440x180mm size, including waste coupling and waste pipe all as specified and directed. |
| 55 | S&F Vitreous China wash down water closet pan of size 540x375x415mm 'P' trap or 'S' Trap (pedestal pattern), any colour including necessary fittings and flush pipe etc (excluding flushing cistern) all as directed. |
| 56 | S&F 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, any colour , with inlet, ball valve, float and handle including brackets, and necessary connections to pipes complete all as specified and directed. |
| 57 | S&F PVC water closet seat cover (any description and any colour), closed pattern and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 58 | S&F brass chromium plated Hand shower (Health Faucet)(ABS Body) with 1.00 Meter long Easy Flex Tube in Chrome Finish and wall Hook complete all as specified and directed. |
| 59 | S&F CP Towel Ring fixed with and including Chromium plated brass screws and wall plugs (Minimum weight 90gms) complete all as specified and directed. |
| 60 | S&F Pillar taps, cast copper alloy chromium plated, fancy type, screwed down, high pressure with long screwed shanks and fly nut of 15/20mm bore complete all as specified and directed. |
| 61 | S & F Bib Taps, cast copper alloy heavy duty, 15 mm dia, Chromium Plated, long body Fancy Type screwed down for iron pipe and fixed etc complete all as specified and as directed. |
| 62 | S&F two way bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore complete all as specified and directed. |
| 63 | S&F Angular stop cock cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore complete all as specified and directed. |
| 64 | S&F 15 mm dia Stop cock chromium plated fancy type with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe/CPVC pipe or for unions and fixed complete all as specified and directed. |
| 65 | S&F PVC connection 15mm size with CP brass Nuts of legnth 600 mm complete all as specified and as directed. |
| 66 | S&F 100mm dia CP grating incl joints with solvent cement complete all as specified and directed. |
| 67 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 68 | S&F 600 mm long CP Brass Towel Rail fixed to wall with necessary chromium plated screws and wall plugs complete all as specified and directed. |
| 69 | S&F Waste pipe any dia (32/40mm) alongwith necessary fittings connected to wash hand basin /kitchen sink complete all as specified and directed. |
| 70 | S&F CP Toilet paper holder fancy type high quality |
| 71 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 72 | Dismantling Asbestos Cement Corrugated or Semicorrugate in Roof covering, complete all as specified and directed. |
| 73 | M&L proparing newly plastered surfaces of wall and applying two coats of high sheen, Anti-Fungal, Excellent Stain Resistant interior Acrylic emulsion paint over a coat of primer complete all as specified and as directed by Engineer-in-charge. |
| 74 | M&L for applying a layer of 1mm thick wall care putty on wall and making surface even and smooth complete all as specified and as directed. |
| 75 | Dismantling of wall / ceiling boards (fiber, pulp, insulation etc) / insulation boards /slabs/blankets of any thickness including cover fillets ridges etc, complete all as specified and directed. |
| 76 | Providing & fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. |
| 77 | M&L 75mm thick PCC 1:3:6 Type C-2 using 20mm crushed stone aggregate as in plinth protection, flooring etc finished even and fair without using extra cement complete all as specified and directed. |
| 78 | S&F 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 79 | M&L Concrete bed to drain pipes 150 mm dia including packing under and haunching against the sides of the pipes after they are laid and tested complete all as specified and directed. |
| 80 | M&L for PCC (1:3:6) Type C2 ( using 40 mm graded stone aggregate) in surface channels and PCC drains complete including necessary formwork complete all as specified and directed. |
| 81 | M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone agg as in cover slab and set in cement mortor 1:6 complete incl necessary form work complete all as specified and directed. Note :- Reinforcement shall be measured and paid seperately |
| 82 | M&L TMT bar 10mm dia and over cut to length bent to shape reqd incl cranking binding spirally for hooking,binding with and including mild steel wire (Annealed) not less than 0.9mm dia as in reinforcement complete all as specified and directed. |
| 83 | M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups spaces and binder cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. |
| 84 | S&F PVC (SWR) floor traps 100mm bore with stainless steel grating (measured seperately) including jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 complete all as specified and directed. |
| 85 | S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note :- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. |
| 86 | S&F Factory made single 30 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws etc., complete all as specified and as directed. (Note: stainless steel butt hinges and necessary S S screws incl in this item) |
| 87 | S&F for 125 mm long Butt hinges, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-11 etc., complete all as specified and as directed. |
| 88 | S&F for 150mm aluminium anodised barrel tower bolts of extruded section and fixed etc., complete all as specified and as directed. |
| 89 | S&F for 300mm aluminium alloy anodised sliding bolts with hasp, staple and fixing clips of sheet, cast or extruded section fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed etc., complete all as specified and as directed. |
| 90 | S&F PVC Septic tank of capacity 2000 LTR including excavation and Returning, filling Removel ,and including P.C.C 1:4:8 & block work reqd for fixing of septic tank all as specified and directed. Make plasto or sintex or equivalent Please Enable Macros to View BoQ information |
| 91 | S&F PVC Septic tank of capacity 2000 LTR including excavation and Returning, filling Removel ,and including P.C.C 1:4:8 & block work reqd for fixing of septic tank all as specified and directed. Make plasto or sintex or equivalent Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender