Tender for Tender for Remaining Construction Work Of 30 Meter Wide Master Plan Road On Pachgai Land Acquired By Agra Development Authority (Part-A)
Tender Value
Ref. Documents
Estimated cost
Bid Submission
17 Nov 2026
15 days left
EMD
47.16 Lakhs
Bank guarantee accepted
Document Fee
23600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Agra → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Remaining Construction Work Of 30 Meter Wide Master Plan Road On Pachgai Land Acquired By Agra Development Authority (Part-A)
BOQ
| Sl. No. | Item Description |
| 1 | Earth work : Earth work in cutting or in embankment in ordinary soil excavation to be in the form of a regular pits not exceeding 0.50m in depth and earth work in embankment to be in 20cm layers including ramming and dressing the surface to required levels and slopes and also including 1.5 m lift and 30m ]ead. The earth in form of cutting (b) to be used as spoil banks within 50m distance as directed by the Engineer-in-Charge. Mannual (Small work) SOR 23-24 |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil (DSR No.2.8.1 2023) |
| 3 | Carriage of Earth on kaccha Roads (Cartage of earth 5km. Distance) (183.50-53)+33.33% for kaccha road 231 (a) Sor 25-26 |
| 4 | CEMENT CONCRETE (CAST-IN-SITU): Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: (DSR No.4.1.8 2023) 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | Centring and shuttering including strutting, propping etc. and removal of form for :5.9.1 Foundations, footings, bases of columns, etc. for mass concrete DSR 2023 |
| 6 | Centring and shuttering including strutting, propping etc. and removal of form for :Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. (DSR No.5.9.2 2023) |
| 7 | Centring and shuttering including strutting, propping etc. and removal of form for :5.9.3 Suspended floors, roofs, landings, balconies and access platform DSR 2023 |
| 8 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. (DSR No.5.22.6 2023) Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 9 | DESIGN MIX CONCRETE: Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum ) (DSR 2023 No.5.33.1.1 |
| 10 | Road Work: Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres (DSR 2023 No.16.1) |
| 11 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at ONIC, arrd compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification clause 401.(Pre sanction Rate) (SOR 2025-26 No. 20.1) |
| 12 | Providing, laying spreading & compacting graded stone aggregate of approved quarry to wet mix macadam (WMM) specification including premixing the material with water at O.M.C in machenical mix plant carriege of mixed material by tipper to site, lating in uniform layers with paver in sub -base /base course on well prepared suface & compacting with vibroatory roller to achieve the desired density complete as per MoR &H clause 406& as directed by Engineer Incharge including all machine charges & including all labour, T& P etc req for proper completion of work. (PSR) |
| 13 | Providing, & applying Priming Coat with bitumen emulsion(SS1) on prepared surface of grangular base including cleaning of road surface and spreading primer @ 0.70 kg/sqm. using mechanical means. Rates including of bitumen emulsion. (As per MORTH 502 , MORT&H 2024 Rates taken from SOR 2025-26) |
| 14 | Providing and laying Dense Graded Bituminous Macadam with higher capacity batch type HMP using crushed stone aggregates of specified grading, premixed with Bituminous binder(VG-30) @4.5% by weight of total mix and filler,transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density as per MORTH specification clause No. 505 (MORT&H 2024 Rates taken from SOR2025-26) |
| 15 | Providing, & applying Tack coat with bitumen emulsion SS1 using emulsion pressure distributor @ 0.25 kg/sqm on the prepared grangular/ old painted surface, cleaned with mechanical broom including all Taxes material, labour, T& P etc. required for proper completion of work. Rates including of (As per MORTH 503 MORT&H 2024 Rates taken from SOR 2025-26) |
| 16 | Providing and laying Bituminous concrete with higher capacity batch type hot mix plant using crushed stone aggregates of specified grading, premixed with Bituminous binder (VG-30) @5.4% by weight of total mix and filler, transporting the hot mix to work site, laying with paver finisher with sensor control to required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. as per MORT & H specification clause no. 507. MORT&H 2024 Rates taken from SOR2025-26) |
| 17 | Retro-ReflEptlvesheeting typ6-Xlwith 4 mm thick ACM Single SidE Providing & fixing of reflective signs wilh a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panelface to be fully covered with High lntensity prismatic sheeting type lV as per IRC-67:2012 retro reflective sheeting with back frame lVlS angle of 35x35x5 mm. Legends , letters , numerals and borders etc should be as per IvloRIH specificalion No- 801.3.7 The sheeting shall have a pressure - sensilive adhesive of the aggressive - lack type requiring no heat solvent other preparation for adhesion to a smoolh clean surface, in a manner recommended by the sheeting manufacturer. The ACM (Aluminium Composite Materials) shall be fixed on the Back frame MS Angle with riveting. lvlicro prismatic type lV Relro retleclive sheeling conlirming to ASTM D4956-09 shall be Pressure fixed. The Relro reflective sheeting shall be lested for a cedificate of having the sheetingmtested for coef,lcient of retro reflection, da)'lime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance. 3 years outdoor weathering and lts having passed these tests shall be obtained lrom lnternational/Government Laboratory/ lnstitute by lhe manufacturer of the sheeting and in case the certi,lcate ls obtained from lnlernational condition, it should also be obtained from lndian condition within 3 years of launching of product by the manufacture in abroad Alternatively, a certificate conforming to ASTM Speciflcation (O 4958-09) onartificial accelerated wealhering requirements from a reputed laboralory in lndia can be accepted provisionally. ln such a situation, the Employer/Client, ifso desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requiremenl of three years outdoorweathering of the sheeting as per IRC 6712012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials,labour, T&P, transportation, installation and incidentals all complete as per direction of lhe Engineer-ln-Charge SOR 2023-24 No. 26.12) |
| 18 | Road N.4arking with Hot Applied Thermoplastic Compound with Reflectorislng Glass Beads on Bituminous Surface. Providing and laying of hot applied thermoplaslic compound 2.5 mm thick including reflectorising glass beads 0? 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 Thellnished surface to be level, uniform and free from streaks and holes. (SOR 2023-24 No. 28.2) |
| 19 | Rellective Raised Pavement Markers (Cat Eye/ Road stud) Supply and fixing of raised pavement marker with l\'4ade of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrile) or HIPS (High-lmoact Polystyrene) orAcryloniitrite Butadien Styrene (ABS) or Any other suilable material approved by the Engineer. The Marker shall support a load of 13,635 kg testod in accordance with ASTM D42B0.The Refleclive panels shall consist of number of lenses containing single or dual prismaticcubes capable of providing total internal refection ol the light entring the lens face. Lenses shall be mouled of methyl methecrylate conforming to ASTI\'4D788 of equivalent. The slop or ret.o-reflecting surface shall preferably be 35+1-5 degree to base and the area oI each retro -reflecling surface shall not be less than 13.00 sq.cm. the marker height shall not be less lhan 10 mm and shall not exceed 20 mm & Width shall not exceed 130 mm. The base of lhe marker shall be flat wlthin 1.3 mm all road studs shall be legibly marked with the name . t.ade or other means of identification of the manufacture. epoxy lnstallations, excess adhesive around the edge ofthe marker, excess adhesiveon the pavement and adhesive on the exposed surfaces of the markers shall be immediaiely removed. The contractor shall submit a two year warranty forsatisfactory field performance including stipulated retro-reflectance of the reflecting panel , to the Engineer . ln addition a two year warranty for satisfactory jnfield pe.formance ofthe finished road marker shall also be given by the conlractor who carries out the work of lixing of reflective road markers. ln case the markers are displaced , damaged . get worn out or lose their reflectivity compared to stipulated standards , the contractor would be required to replace all such markers within 15 days ofthe intimation from the Engineer .at his own cost The rate shall include all materials, labour, T&P, transportalion, installation and incidentals all complete as per direction of the Engineer-in-Charge. RPM (with shank) (SOR 2023-24 No. 28.2) |
| 20 | Class-150 (Non Modular) brick work in 1:4 Cement and Coarse sand mortar in foundation and plinth including supply of all materials, labour and T & P etc. required for proper completion of the work. (CH-6.1.1 DSR ) |
| 21 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (DSR 2023 no. 16.69) |
| 22 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR2023 |
| 23 | Type - A, 'W\\": Metal Beam Crash BarrierProviding and erecting a 'W' metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high. 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810. SOR 25-26 ch.8 SI.No. 27 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender