Tender For Construction Of Hostel At Mlri Manasbal, Skuast-K (Capex).
Tender Value
10.75 Crore
Estimated cost
Bid Submission
21 Nov 2026
18 days left
EMD
21.51 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Hostel At Mlri Manasbal, Skuast-K (Capex).
BOQ
| Sl. No. | Item Description |
| 1 | STRUCTURAL PART |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. (Including dewatering if any upto plinth level)All kinds of soil : |
| 3 | STONE SOLING: Providing and laying of hand packed stone soling (size 150 mm-230mm), before laying of mud mat, compacted, consolidated, rammed and filling the voids with fine sand - all complete incl carriage upto site of work with all head loads. |
| 4 | MUDMAT: Cast-in-situ of concrete work of nominal mix concrete M7.5 grade (1:4:8) nominal maximum size of stone aggregate 40mm volumetric batching in foundation trenches and ground floor, including curing but excluding formwork costs |
| 5 | MASS CONCRETE: Providing and laying mass concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in Below Ground and Above Grouns Plinth retaining walls, (any thickness) including attached pilasters, including curing but excluding the cost of centring, shuttering and finishing with. |
| 6 | CAST-IN-STU DESIGN MIX M25: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,incluyding pumping of concrete to site laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportiond as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable seperately all works Below Plinth Levl / Above Plinth Level upto level V (AGL/BGL). |
| 7 | UPTO PLINTH LEVEL |
| 8 | ABOVE PLINTH LEVEL |
| 9 | EXTRA CEMENT QUANTITY: For design mix M25 over 330kg/m3 |
| 10 | FORM WORK: Centering and shuttering including strutting, propping etc. and removal of formwork from the site, for all works from foundations, to roof level |
| 11 | BELOW PLINTH LEVEL |
| 12 | ABOVE PLINTH LEVEL |
| 13 | SLAB EDGES |
| 14 | PLINTH FILLING: Supplying and filling in plinth with GSB/ Second class sand under floors including, watering, ramming, consolidating and dressing complete including carriage, leads and lifts. |
| 15 | BACK FILLING: Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 16 | STEEL REINFORCEMENT: Steel reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding - all complete from foundation to roof level of Thermo-Mechanically Treated bars of grade Fe-500D or higher. |
| 17 | EXPANSION JOINT |
| 18 | STRUCTURAL STEEL:Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. plates, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer also included. |
| 19 | ANCHOR BOLTS: Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 20 | ARCHITECTURAL PART |
| 21 | Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :6 (1 cement : 6 coarse sand) |
| 22 | Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level |
| 23 | Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in :(Cement mortar 1 :4 (1 cement : 4 coarse sand) Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry. |
| 24 | 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 fine sand) |
| 25 | 12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 coarse sand) |
| 26 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.Glass DGU (6+12+6) Sample to be approved by EIC. |
| 27 | Providing and fixing of U-PVC sliding/casement/fix doors in whote colour,frame 60mm thick (min) x 45mm (min) with 1.5 mm GI reinforcement sash 39mm (min) 58mm (min) with 1.25mm GI U section reinforcement with rubber gasket of grey / black colour 10 years warranty against weathering of profile with complete hardware fittings fixed with 12mm thick laminated board panels as per design and with 5mm toughened glass and fiber jalli option if pre- febricated on german fabrication system( mosquito sash 18mm(min) x 43mm(min)(with welled cornes) complete at site including all fixtures |
| 28 | Providing and fixing wood work in frames of doors, windows and other frames, wrought framed and fixed in position including SS expansion fastners for brick / concrete work in (including cost of all material, leads, lifts and carriages etc upto site of work complete wood as per the directions of Consultant/as per the drawings enclosed First class deodar wood |
| 29 | Providing and fixing of 30mm thick (Finished Size) water proof grade solid core Flush Door shutter conforming to IS 2022. The core shall be bonded with Phenol Formaldehyde resin and chemically treated against termites. The shutter is to be finished with 1.00mm thick premium laminated of ReputedBrand on both sides using high-strength adhesive.Edges to be finished with matching polished hardwood lipping. price to be includes costof Doors, laminated, adhesive,labour for manifacturing and freight to the site. |
| 30 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 31 | Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass) |
| 32 | Modular door lock ss finish handle 10\\" with duaal locking system inside & outside (godrej) |
| 33 | L -drop (300 x 16mm) |
| 34 | Tower bolts 150mm (doors) |
| 35 | Handle 125mm (door) |
| 36 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 37 | Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 38 | Granite Work in Floors :- Providing and fixing ( gang saw cut mirror polished (flamed , pre-moulded and pre-polished), machine cut for flooring, steps ,risers of stairs etc.( flamed instaircase) of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (of edges wherever required ) and polishing to edge to give high gloss finish etc. complete at all levels. Granite of any colour and shape 16mm thick. and slab area over 0.50 sq m. (Note: The Granite stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc. upto site of work complete. |
| 39 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete.(Size 1200 x 600 mm) |
| 40 | Providing and Fixing of pre rubed & pre polished (in finished form) kota stone 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, with base of cement mortar 1:4 (1 cement : 4 coarse sand) : |
| 41 | Providing and Fixing of pre rubed & pre polished (in finished form) kota stone in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement motor 1:3 (1Cement:3 course sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs. |
| 42 | Providing and laying Vitrified tiles in floor/Walls with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size 600 x 1200 mm |
| 43 | Providing and fixing devri stone 25 mm thick with exposed face fine dressed with rough backing on floor / ramp / plinth face etc. upto 10 meter ht back filled with a grout of 50 mm thick cement sand mortar in 1:3 (fine cheiseled)including pointing in white cement 1:2 with admixture of pigment matching to stone |
| 44 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc.,by applying cemnet slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement@ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement compound @ 0.126 kg/sqm. This layer will be allowed t air cure for 4 hours followed with water curing of 48 hours. The rate includes preparation of surface, treatment and sealingof all joints ,ciorners, juntions of pipes and masonry with polymer mixed slurry. |
| 45 | French spirit polishing, Two or more coats on new works including a coat of wood filler ( FLUSH DOORS ) |
| 46 | Providing and applying cement based wall putty of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified patter. (Birla make) (including cost of all material, leads, lifts and carriages etc upto site of work complete).2 mm thick (WALLS & CEILING) |
| 47 | Wall Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 48 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. |
| 49 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.(Crushed) |
| 50 | Providing and fixing poly corbonate corrigated sheet roofing of approved quantity upto any pitch including fixing withpolymer coating with J,L,hooks,bolts & nuts, 8mm thick dia G.I bituminous washers. Complete job |
| 51 | Providing and fixing Track deck CRIL make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness ) |
| 52 | Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges/Valley plain (500 - 600mm) |
| 53 | Pointing on exposed brick masonry external surfaces with lime surkhi finish (I Lime: 2 Surkhi ) mixing in approved proportion, including raking out joints, cleaning and preparation of surface, applying and finishing joints in ruled/pointed pattern as directed, curing, including grinding the brick surface where required, finishing true to line, level and plumb, complete in all respects including cost of all materials involved, including scaffolding/staging and all incidental charges as directed by the Engineer-in-Charge.. |
| 54 | Providing and Fixing of 50mm dia stainless steel railing of 304 grade of hallow tube 1.6 mm thick of Jindal/Salem make or equivalent including welding and fixing with stainless steel machine screws for making required size and shape, buffing etc. Complete and fixing stainless steel balusters upto 900 mm height and S S tubes, three in one installed horizontally including cutting, welding, grinding to required shape and size by required steel dash fasteners, nuts, bolts, screws ,etc. in floors and treads including providing SS shoe at each balusters complete as per architectural drawings and as per the directions of engineer incharge including cutting of granite/marble floors and fastening with lead grouting if required, complete in all respects. |
| 55 | Providing & fixing of stainless steel nevel post (Ornamental ) including top ball of AISI 304 grade of required height duley anchored to floor with dash fasteners . Height of the nevel post shall not be less than 1050 mm above the finished skirting level all complete as per architectural drawings (including cost of all material, leads, lifts and carriages etc upto site of work complete).Complete as per the directions of Engineer incharge. |
| 56 | Providing and making 125mm Ornamental Cement Moulding of Ratio 1:1 (1cement 1sand) Including all materialfrom source to site and scaffolding, Inclusive of white exterior paint, and design to be approved by Engineer incharge. |
| 57 | PLUMBING |
| 58 | I-China Ware |
| 59 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: |
| 60 | W.C. pan with ISI marked white solid plastic seat and lid. |
| 61 | Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required:- |
| 62 | White Vitreous China Under Counter Wash basin. |
| 63 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 64 | Kitchen sink with drain board |
| 65 | 510x1040mm bowl depth 250mm |
| 66 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 67 | II-C.P Fitting and Accessories |
| 68 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing |
| 69 | Rectangular shape 1500x450 mm |
| 70 | Providing and fixing toilet paper holder with Flap made out of C.P Brass |
| 71 | Providing and fixing C.P Brass Soap Dish. |
| 72 | Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws 600 mm long . |
| 73 | Providing and fixing CP Short Body Bibcock with Valve Flange |
| 74 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 |
| 75 | Providing and fixing CP Brass wall mixer of quality & make as approved by Engineer in charge. |
| 76 | 15 mm nominal dia |
| 77 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 78 | Providing and fixing CP Brass Health Faucet of quality & make as approved by Engineer in charge |
| 79 | 15 mm nominal dia |
| 80 | Providing and fixing Stainless Steel Retractable Sink Basin Water Drain Pipe of approved quality & make and as per the direction of Engineer-in-charge. (For Kitchen Sink) |
| 81 | Providing and fixing CP Brass Sink Mixer with Regular Swivel Spout of quality & make as approved by Engineer in charge. |
| 82 | III-SOIL, WASTE AND VENT PIPES |
| 83 | Providing and fixing on wall face un-plasticized Rigid PVC water pipes conforming to IS: 13592 Type B including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.including all fittings plain bend,tee,trap,door bend,collar etc as per directed by Enginer I/C |
| 84 | 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B |
| 85 | 75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B |
| 86 | Providing and fixing of Rain Water pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing. |
| 87 | 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-A |
| 88 | Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required. Makes:- Astral/SFMC/Finolex |
| 89 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design : |
| 90 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : |
| 91 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 92 | Supply, Installation of PVC Gully Trap of Size 110 mm |
| 93 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of P.V.C pipes including bed concrete as per standard design : |
| 94 | 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B |
| 95 | IV-WATER SUPPLY |
| 96 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. |
| 97 | Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. |
| 98 | 15mm nominal outer dia pipes |
| 99 | 20mm nominal outer dia pipes |
| 100 | 25mm nominal outer dia pipes |
| 101 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. |
| 102 | Internal work-exposed on wall with clamps at 1.00 meterspacing |
| 103 | 20mm nominal outer dia pipes. |
| 104 | 25mm nominal outer dia pipes. |
| 105 | 32mm nominal outer dia pipes. |
| 106 | 40mm nominal outer dia pipes. |
| 107 | External work including trenching and refilling etc.complete |
| 108 | 50mm nominal outer dia pipes. |
| 109 | Providing and fixing unplasticised PVC connection pipe with brass unions: |
| 110 | 45 cm length15 mm nominal bore |
| 111 | Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks |
| 112 | Supplying and Fixing of Elastomeric foam Insulation made from Nitrile Rubber with Density not less than 50 Kg/Cu.m,Thickness 10 mm for a Temp Range of -40 Deg C to 105 Deg C |
| 113 | V-PVC STORAGE TANKS,VALVES AND GEYSERS |
| 114 | Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc. |
| 115 | 50 mm Diameter |
| 116 | 40 mm Diameter |
| 117 | 32 mm Diameter |
| 118 | 25 mm Diameter |
| 119 | Providing & Laying of Pre Cast RCC Rings of concrete grade (M-20) 1200mm dia for making of Sokage pits inclusive of all earthwork,laying of precast rings,with RCC slab top & interconnecting with pits which shall be made Staggerly or as directed by Enginer I/C |
| 120 | Making septic tank of Outer dimensions (5m x 2.5m) with a clear depth of 2.5m With F.P.S. bricks with class designation 75 n (Outer walls 0.35m thick) in cement mortar 1:4 (1 cement: 4 coarse sand) including 2 no Baffle walls (0.23m thick), Floor concrete 1:2:4 mix 75mm thick over pcc 1:4:8 125mm thick, RCC Slab At Top (150mm Thick), 2 No C.I Covers (Heavy Duty) inside plastering 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement complete including earthwork & stone soling 150mm as per standard design specified/approved by Engineer in charge |
| 121 | Providing and fixing on wall 50 LTRS Electric Geyser with ABS Body. |
| 122 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 123 | VI-PVC STORAGE TANKS,VALVES AND GEYSERS |
| 124 | Supply,Installation,Testing and Commissioning of Open Well Submersible Pump with a Discharge of 8.0 Cu.m/hr @Head of 45 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel. |
| 125 | Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work complete in all respects. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender