Tender For Construction Of Canopy For B Site Ro/Fuel Station, Spinning Mill At Iie Kashipur, (U.S.Nagar) Uttarakhand
Tender Value
26.33 Lakhs
Estimated cost
Bid Submission
17 Nov 2026
16 days left
EMD
52700
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Udam Singh Nagar → Uttarakhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Canopy For B Site Ro/Fuel Station, Spinning Mill At Iie Kashipur, (U.S.Nagar) Uttarakhand
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. |
| 2 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 7 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : |
| 8 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. |
| 10 | Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 11 | Providind and Fixing Klippon Galvalume steel profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of Cold rolled steel confirming to IS:513-2008 of base metal thickness 0.50mm, having Yield stress of Min 275 Mpa. Steel Surface shall have hot dip metallic coating of Al-Zinc alloy comprising 55% Aluminium, 43.5 Zinc and 1.5% Silicon as per the ASTM-A792M, with total mass of coating on both sides shall be 150gms/sqm. The steel shall have organic coating wiht silicon Modified Polyester (SMP) Super Durable Polyester (SDP) paint on continous coil coating line. The thickness of coating on top side shall be 20-25 Microns (i.e. 15-18 microns SMP/SDP paint over epoxy primer and back side 8-10Microns SMP/SDP paint over epoxy primer. Total Coated Thickness (TCT) shall be 0.58MM. Sheet shall have protective guard film of thickness of 25 microns minimum to avoid scratches while transporation and should be supplied in single length up to 6m or as desired by Engineer-in-Charge. |
| 12 | PROFILE Sheet for roofing |
| 13 | plain Ridges plain (500 - 600mm) |
| 14 | Flashings/ Aprons.( Upto 600 mm) |
| 15 | P/F 700mm wide rain water gutter fabricated out of 1200mm wide roll of 18 gauge aluminium sheet |
| 16 | Providing and fixing 150F/200F flush panel. (pre-coated steel) False Ceiling made of Cold rolled sheet conforming to IS 513 having minimum yield stress and tensile stress as 240Mpa and 300 Mpa respectively. Base metal thickness for ceiling panel and Carriers shal be 0.45mm and 0.5mm respectively. The steel surface shall have hot dip metallic coated with Zinc coating (galvanizing) as pr IS277 with total mass of coating on both sides shall be 120gms/sqm. The steel shall have organic coating wih Regular Modified Polyester (RMP) paint on continuous coil coating line. The thickness of coating on top side shall be 20-25 Microns (i.e. 15-18 microns RMP paint, over 5-7 microns epoxy primer) and back side 8-0 Microns RMP paint over epoxy primer. Total coated Thickness (TCT) shall be 0.50 MM for Ceiling Paneland 0.60MM for Carrier. Sheet shall have protective Sheet shall have protective guard film of thickness of 25microns minimum to avoid scratches while transportation and should be supplied in single length up to 6m (for panel) and up to 5m (for carrier) or as desired by Engineer-in-Charge. The ceiling panel shall be clipped into carriers which are suspended from steel. |
| 17 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 18 | In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete |
| 19 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 20 | 110 mm diameter |
| 21 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 22 | Bend 87.5° 110 mm bend |
| 23 | Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 24 | New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution |
| 25 | Cabling and allied work 3corex1.5 sq.m copper cable FRLS outer sheathed of 1.1 KV grade of upto 35 sqmm size direct in existing RCC/Hume pipe |
| 26 | Cable Termination gland Non- FLP heavy duty double compression gland, end termination, crimpng type lugs & allied jointing material etc. 3 corex 1.5sq.m |
| 27 | S/f of SP MCB upto 32 Amp |
| 28 | 10S.W.G. Cu. Wire |
| 29 | Supply & Fixing of flame proof junction box(4 way) |
| 30 | SITC of recess mounted linear LED lights 80 watt Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender