Tender For E Tender For The Renovation Works Of Parlour At Marangattuppally
Tender Value
Ref. Documents
Estimated cost
Bid Submission
05 Nov 2026
2 days left
EMD
6700
Bank guarantee accepted
Document Fee
670
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kottayam → Kerala
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for E Tender For The Renovation Works Of Parlour At Marangattuppally
BOQ
| Sl. No. | Item Description |
| 1 | EARTH WORK :- Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 2 | Filling and levelling available excavated earth (excluding rock) in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m |
| 3 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil |
| 4 | CONCRETE WORK :- Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 5 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work: 1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 6 | Centering and shuttering including strutting, propping etc. and removal of form work for:Retaining walls, return walls, (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 7 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete .Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 8 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer and two coat of epoxy paint, all complete, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes |
| 9 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of epoxy paint, all complete. |
| 10 | Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 11 | 20 mm cement plaster of mix:1:4 (1 cement : 4 fine sand) |
| 12 | Finishing with Deluxe Multi surface paint system for exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm |
| 13 | INTERLOCKING PAVERS :-Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 14 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 15 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x 1040 mm bowl depth 225 mm |
| 16 | PVC WORKS :-Supply and fixing of pvc pipes including all pvc bends ,elbows etc.complete all .as per direction of engineer in charge. 25 mm |
| 17 | Supply and fixing of pvc pipes including all pvc bends ,elbows etc.complete all .as per direction of engineer in charge. 32 mm |
| 18 | Supply and fixing of pvc pipes including all pvc bends ,elbows etc.complete all .as per direction of engineer in charge. 63 mm |
| 19 | Supplying and fixing SS bib cock superior quality including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. Make : CERA/ Jquar/RAK/Hindware.complete with all plumbing works |
| 20 | Supply and laying of 50 mm thick baby metal over approved weed-control geotextile fabric, including spreading and levelling to the required thickness and level, complete as directed by the Engineer-in-Charge. |
| 21 | Providing and fixing aluminium composite panel ceiling and fascia using aluminium extruded architectural sections of size 25.4x25.4x1.2mm(0.308kg/m) to form grids of size 600x600mm and fixing 3mm thick FR grade aluminum composite panel (0.25mm aluminium coil thickness) of approved make and colour to the frame work using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant etc. The basic frame work shall be propoerly hung/fixed on the existing roof structurals using aluminium extruded angles/square tubes at proper intervals. |
| 22 | Providing and fixing false ceiling with 7.5 mm thick PVC wooden grains panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete |
| 23 | Providing and fixing aluminium powder coated side hung door partialy glazed and partlially panelled with aluminum architetural sections of size as per drawing and specification. Charges inculding providing necessary fittings ,locking system etc. complete. |
| 24 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm) with double speed adjustment with necessary accessories and screws etc. complete. (basic rate Rs.1500/-) |
| 25 | Providing and fixing structural glazing using powder coated aluminium extruded architectural sections of size 71.2x28x2.8mm(1.136kg/m) to form grids of size maximum of 600x750mm and fixing 5mm thick approved reflective type glass. Securely fixing the basic frame work on to the masonry/rcc/ms structure with adequate and properly designed anchor fastners, fischer/hilty make nuts and bolts etc including providing himax windows in required intervals. complete. as per the drawings/directions of engineer in charge and specificaitons |
| 26 | Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar |
| 27 | Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender