Tender For Addition/Alteration Of Bldg No P-220 At Chaf Banglaore
Tender Value
Ref. Documents
Estimated cost
Bid Submission
19 Nov 2026
4 days left
EMD
9726
Bank guarantee accepted
Document Fee
300
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bengaluru Urban → Karnataka
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration Of Bldg No P-220 At Chaf Banglaore
BOQ
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc., complete all as specified and as directed by Engr-in-charge. |
| 2 | Demolition of cement concrete in ground floor and paving not exc 15 cms thick below or above GL complete all as specified and as directed by Engr-in-charge. |
| 3 | Demolition brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc., but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed by Engr-in-charge. |
| 4 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc 1.50 sqm each complete all as specified and as directed by Engr-in-charge. |
| 5 | Material and labour for type B-2, 1:2:4 (Using 20mm graded stone aggregate) as in copings pilast,roof kerbs, buttresses columns, pillars, boundary pillars and posts (incl caps and bases) complete all as specified and as directed by Engr-in-charge. |
| 6 | Material and labour for precast cement concrete block masonry with soild blocks, type C-1, 1:3:6 (Using 20mm graded stone aggregate) exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed by Engr-in-charge. |
| 7 | Material and labour for providing cement concrete type B-0, 1:2:4 (Using 12.5mm graded stone aggregate) as in roof kerbs, padding or mud stops, rounded or chamfered on edges complete all as specified and as directed by Engr-in-charge. |
| 8 | Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge. |
| 9 | Material and labour for rendering 10mm thick in cement mortar 1:6 and 5mm thick in cement mortar 1:4 in two layers on fair faces of brick work or concrete surfaces with water proofing compound @ 200 ml per 50 kg of cement or as per manufacturer's instruction etc., finished even and smooth without using extra cement complete all as specified and as directed by Engr-in-charge.Notes: (i) WPC shall be measured and paid separetely.(ii) Scaffolding upto tripple storey deemed to include item rate .Contractor may qoute rate accordingly. |
| 10 | Supply only liquid water proofing compound complete all as specified and as directed by Engr-in-charge. |
| 11 | Material and labour for stone walls cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 20cm girth complete all as specified and as directed by Engr-in-charge. |
| 12 | Dismantling plain or corrugated steel sheeting any guage, thickness including roof covering etc., complete all as specified and as directed by Engr-in-charge. |
| 13 | Dismantling wrought iron or mild steel work of any description complete all as specified and as directed by Engr-in-charge. |
| 14 | Supply and fix for prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-charge. |
| 15 | Supply and fix for rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plats etc., Fe 410-W (Gde E-250) quality-A complete all as specified and as directed by Engr-in-charge. |
| 16 | Supply and fix for plates (plain or chequered) channels, distance pieces, cleats etc., square cut or notched including riveted, bolted or welded attachment complete all as specified and as directed by Engr-in-charge. |
| 17 | Material and labour for water proofing treatment on horizontal and vertical surfaces with applying of oil bound bitumen primer @ 0.20 Kg/sqm and providing 4mm thick APP modified water proofing membrane weighing not less than 4.0 Kg/sqm reinforced with non woven polyester matt weighing not less than 160 gms/sqm having softening point not less than 150 degree centigrade, having tensile strength of 650 N/5cm and 350 N/5cm in longitudinal and transverse directions respectively of the reinforced tearing strength of 180N by torch on application including minimum 10cm side over lap and 15 cm end lap applying a coat of blown grade hot bitumen 90 /15 over the membrane @ 1.20 Kg/sqm finished with solar reflective bituminus paint/primer @ 0.10 kg per sqm incl dismantling of existing APP membrane complete all as specified and as directed by Engr-in-charge. |
| 18 | Material and labour for preparation of new plastered surfaces of wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant priming paint complete all as specified and as directed by Engr-in-charge. |
| 19 | Material and labour for applying 2mm thick wall care putty on wall including preparation old surface /new surfaces plastered or unplastered surfaces complete all as specified and as directed by Engr-in-charge. |
| 20 | Material and labour for preparing old plastered or unplastered surface of walls and applying two coats of cement based paint on walls complete all as specified and as directed by Engr-in-charge. |
| 21 | Material and labour for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or with steel wire brushing, scraping down smoke soot’s, moulds, moss and efflorescent salts and treating oily and greasy spot, filling holes and cracks with suitable material like white cement or plaster of paris and applying two coats of oil bound distemper through mechanical means including necessary scaffolding upto 6th storey complete all as specified and as directed by Engr-in-charge. |
| 22 | Material and labour for preparing new plastered or unplastered old surface of walls and applying two coats of cement based paint on walls including with alkali resistant priming paint complete all as specified and as directed by Engr-in-charge. |
| 23 | Material and labour for two coats of synthetic enamel paint on new steel surfaces over coat of red-oxide primer including preparation of surfaces, over 10cm width or girth including preparing roof painting complete all as specified and as directed by Engr-in-charge. |
| 24 | Material and labour for powder coated aluminium windows of three tracks outer frame top, side sections, bottom frame (track) with guide track of size 92.5x31x1.50mm with sliding window shutters two nos with glass and one no with wire mesh (total 3 nos shutter) frame top and side bottom section with wheel track and inner locking section of size 40x18x1.5mm inculding glass 4mm thick and aluminium wire cloth, 0.45mm nominal dia wire and average width of aperture 1.40mm complete all as specified and as directed by Engr-in-charge. |
| 25 | Supply and fix for powder coated aluminium frame work for grills Deco-grill Model DG-104 (10mm) making shape and riveted with rivets and fixed with suitable channel complete necessary fixing arrangements etc., complete all as specified and as directed by Engr-in-charge. |
| 26 | Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portions) with extruded built up standard tubular sections /appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and as directed by Engr-in-charge.Note: All the aluminium sections provided under this item shall be measured and converted into weight for payment with the designated unit weight mentioned in the manufactures catelouge for the corresponding aluminium sections /fittings. |
| 27 | Material and labour for cutting openings through brick walls for doors, windows, or other openings; enlarging existing openings; converting windows into door openings; or cutting out defective brickwork for underpinning includes providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hardcore, etc., to store, and disposing of rubbish, not exc 50m applicable to brick walls built in mud, cement, or lime mortar complete all as specified and as directed by Engr-in-charge. |
| 28 | Material and labour for 75mm thick PCC type C-2, 1:3:6 (Using 40mm graded stone aggregate) as in sub base of hard standing floor finishes etc., laid in alternate panels complete all as specified and as directed by Engr-in-charge. |
| 29 | Material and labour for 75mm thick PCC 1:2:4 type B-2 (Using 40mm graded stone aggregate) as in hard standing floor finishes etc., laid in alternate panels complete all as specified and as directed by Engr-in-charge. |
| 30 | Supply and fix for collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., erected in position and securing runners with holdfasts and brackets complete all as specified and as directed by Engr-in-charge. |
| 31 | Material and labour for framed work such as grills, gratings, etc., with ends of bars shouldered and /or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and as directed by Engr-in-charge. |
| 32 | Material and labour for cutting holes in brick walls built in cement mortar or cement-lime mortar, and in stone walls built in lime mortar, for inserting holdfasts; making good the dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B-1, as required, for thickness exceeding half brick but not exc one brick., complete all as specified and as directed by Engr-in-charge. |
| 33 | Supply and fix for pressed steel frames for doors size 105x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed by Engr-in-charge. |
| 34 | Supply and fix for flush shutters, solid core construction, block board core with plywood face panels, commercial type on both sides, 30mm thick complete all as specified and as directed by Engr-in-charge. |
| 35 | Supply and fix for mild steel sliding door bolt plate type stove enamelled black of length 300mm with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate and fixed complete all as specified and as directed by Engr-in-charge. |
| 36 | Supply and fix for 200mm long of barrel tower bolts stove enameled black with bright bolt complete all as specified and as directed by Engr-in-charge. |
| 37 | Supply and fix for 150mm mild steel pressed handles oval type stove enameled black complete all as specified and as directed by Engr-in-charge. |
| 38 | Supply and fix for floor door stopper of anodised aluminium alloy body and tongue, fitted with hard drawn steel spring, fixed in floor complete with all screws, fasteners and necessary fittings, overall length of cover plate 150mm complete all as specified and as directed by Engr-in-charge. |
| 39 | Material and labour for two coats of synthetic enamel paint on new wooden surfaces over coat of pink primer to new surfaces including preparation of surfaces, over 10 cm width or girth complete all as specified and as directed by Engr-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 19, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender