Tender For Special Repair To Bldg No P-158 (Barber Shop) Of 24 Guards (17 Gdrs) At Pokaran Mil Stn
Tender Value
9.61 Lakhs
Estimated cost
Bid Submission
16 Nov 2026
6 days left
EMD
19500
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaisalmer → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No P-158 (Barber Shop) Of 24 Guards (17 Gdrs) At Pokaran Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises |
| 2 | M/L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite or coloured cement to match, including 15mm thick screed bed in CM 1:6 laying floor finishesed complete all as specified and directed. |
| 3 | . --Ditto-- all as per above but as in skirting over & including 10mm thick backing coat of CM 1:4 all as specified. |
| 4 | S&F Non Skid (coloured) ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over & including 15 mm thick screed bed in cement mortar (1:6) complete all as specifed and as directed. |
| 5 | M&F glazed ceramic coloured tiles (300mmx 450mmx7 mm) in vertical surfaces jointed in neat cement slurry and pointed in white cement. Incl cutting the tiles to the required size whereven required incl mitring the corners etc over 10 mm thick backing coats of cement plaster in CM (1:4) complete all as specified and directed. |
| 6 | Taking down chowkhat or frame existing doors/windows/ventilators (without taking off shutters and guard bars) of exe 1.5 sqm & n. exc 4 sqm etc complete all as specified and as directed incl stacking the materials properly. |
| 7 | M&L for Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and directed approved by Engr-In-Charge including supply and fixing the following items:(a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf.(b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf(c) Powder Coated Aluminium Handles 150 mm - 2 nos per leafMake (Aluminium Sections) : Jindal/Valco/Galco/Hindalco or equivalent as approved by Engr-In-Charge |
| 8 | Taking down aluminium door/ windows incl frames and complete fittings of area exc n 1.50 sqm complete. |
| 9 | Providing and fixing powder coated 50 microns extruded aluminium in 3 Tier Track Sliding Windows/glazing, with frame of section 100x44-45x1.30mm, track of size 100x38.10x1.30 & shutters made of size 32x18x1.3mm, with and including 4mm thick tinted sheet glass selected quality fixed in 2 shutters and stainless steel wire gauage 0.36mm nominal dia of wire and average width of aperture 1.40mm in one shutter and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size and also including powder coated 150mm handle with built in locking system for each leaf complete all as specified.Make (Aluminium Sections) : Jindal/Valco/Galco/Hindalco or equivalent as approved by Engr-In-Charge |
| 10 | S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe Fe 290 Gde E-165 |
| 11 | M&L preparation of new steel surface and applying two coats of synthetic enamel paint ovre a coat of red oxide primer. |
| 12 | M&L for machine cut 20mm thick Granite (of any type)tiles machine cut, in skirting/dado laid over cement screedand jointed with grey cementslurry, and pointed with whitecement with admixture ofpigment to match the shade ofgranite stone including grinding including cutting and polishing types including dismantling of stone slab |
| 13 | M & L for Machine cut kota stone slab flooring 20-25mm thick for window cill, jambs and sofits over and including cement screed base 15 mm thk in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including dismantling of stone slab |
| 14 | M & L for Rounding to edges of stone slabs on edge, such as in steps, cooking platform, and other similar situations |
| 15 | S & F in repair 6mm thick of size 600x450 looking mirror fixed to wall with stainless steel plugs/connecter/ spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered etched smooth finish etc.complete fixed in position all as specified and directed as approved by Engr-In-Charge. |
| 16 | Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete al as specified and directed. |
| 17 | M&L Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions all as specified and directed |
| 18 | S&F for Anodised aluminium snap grid of size of grid 605 x 605mm frame work for false ceiling all as specified and directed. Note :- (i) Main tee, cross tee shall be 35x25x1.5mm & 25x25x1.5mm respectively. Angle at end all along the walls shall be 40x25x2mm. (ii) Rate quoted by the contractor shall deemed to inclusive of frame work complete. |
| 19 | S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 20 | S & F for Rotational moulded polyethylene triple layer white colour water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arranAGEments for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc including taking down existing tank complete . |
| 21 | S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, Make : Hindware / Parryware/Cera or equivalent as approved by Engr-In-ChargeNote : The items for counter will be measured and paid separately. |
| 22 | S&F in repair PVC connection 450mm long and 15 mm dia with brass fly nut at both ends complete. |
| 23 | S & F brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. Cera cat part no F8030104 or equivalentMake : Hindware / Parryware/Cera or equivalent as approved by Engr-In-Charge |
| 24 | S & F in repair Angular Stop Cock, CP, fency type with wall flanage, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete fixed as in repair in all respect all as specified.Make : Jaquar / Hindware / Cera / Prayag or equivalent as approved by Engr-In-Charge |
| 25 | Supplying and laying in repair of CPVC pipes 16mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-Charge. |
| 26 | Supply & Fixing in repair stainless steel Towel Rack with lower hanger size 24'' (600 mm) fixed to walls with hook etc.Cera cat part no F500110 or equivalentMake : Jaquar /Hindware / Cera/ Prayag/Parryware or equivalent as approved by Engr-In-Charge |
| 27 | Supply and fixing in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore fancy type.Make : Jaquar /Hindware / Cera/ Prayag/Parryware or equivalent as approved by Engr-In-Charge |
| 28 | S&F in repairs Soap disc cera cat no F5013116ch CP fixed in position complete fixed as in repair in all respect all as specified.Make : Jaquar / Hindware / Cera / Prayag or equivalent as approved by Engr-In-Charge |
| 29 | Demolition and breaking up drain PVC(SWR) pipes single socketed in any length with rubber joints all as specified |
| 30 | S&F PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or fixed to walls 110 mm bore |
| 31 | S&F PVC (SWR) bends any radius 110 mm bore |
| 32 | S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75 mm |
| 33 | Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed. |
| 34 | M & L for Cement plastering 15mm( thick in two layers -first layer 10mm thick with ready mix plaster and outer layer 5mm thick ready mix water proof plaster) on outer walls by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS- 2250-1981 and shall confirm 28 days compressive strength 10-15 MPA, bulk density 1600-1800 kg/cum and pull out bond strength->0.5 MPA complete all as specified and directed |
| 35 | M & L for rendering 10mm thick ready mix plaster on internal wall by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall confirm 28 compressive days cstrength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA omplete all as specified and directed. |
| 36 | M & L for rendering 5 mm thick ready mix self curing plaster on ceilling by adding potable water by weight of material as mentioned by manufacture ready mix plaster shall comply with IS- 1661-1972, IS-2402-1963, IS-2250-1981 and shall confirm 28 compressive days cstrength 10-15 MPA bulk dencity 1600-1800 kg/cum and pull out bond strength-> 0.5 MPA omplete all as specified and directed. |
| 37 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.Make of Exterior Wall Primer : Asian / BerAGEr / Nerolac [Best Quality] or equivalent as approved by Engr-In-Charge .Make of Internal Emulsion : Asian (APCOLITE PREMIUM EMULSION) / Berger (RANGOLI TOTAL CARE) / Nerolac (PEARL) or equivalent as approved by Engr-In-Charge . |
| 38 | M & L for Applying 3mm thick wall care putty on wall for desired smoothness and levelling of surfaces in two or more layers) for receiving painting complete all as specified and directed.Make of wall Putty : JK wall Putty / Birla Wall care Putty / Bison Wall Putty or equivalent as approved by Engr-In-Charge .Notes : (i) The prepared surface after wall putty, the contractor will inform to the AGE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the AGE as well as to the Engineer-in-Charge through site order. |
| 39 | Dismantling Stone slabs in roofs, suspended floors , chajjas, landings, etc., any thickness, jointed in any mortar complete all as specified and as directed by the Engineer-in-Charge. |
| 40 | Demolition of concrete of any description and in any position (PCC Padding over roof) complete all as specified and as directed by the Engineer-in-Charge. |
| 41 | M&L for PCC 1:2:4 type BO using 12.5 mm graded stone aggregate for levelling course for consolidated thickness shall be varied from 50 mm as per the requirements all as directed by Engr-in-Charge. |
| 42 | M&L for 10mm thick screed plaster on roof for laying in CM 1:4 waterproofing treatment, with using WPC (WPC will be measured and paid separately as supply only) |
| 43 | Supply only integral Waterproofing compound. |
| 44 | M&L for APP based polymeric membrane minimum weighing 3 Kg/Sqm and minimum 3mm thick reinforced with polyester non wove fabric (wt not less than 150 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.3 Ltr/Sqm by forced all as specified and as directed |
| 45 | M & L for 50mm thick plain cement concrete type C-2 (1:3:6) with 20mm garded stone aggregate in plinth protection complete all as specified and directed. |
| 46 | Demolition of stone masonry built in cement or cement lime mortar all as specified and directed. |
| 47 | M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed. |
| 48 | M&L for squared rubble walling, Jodhpur type brought up to courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) all as specified & directed. but except stone |
| 49 | Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses all as specified & directed by Engineer-in-Charge. |
| 50 | Stainless steel tubing of 20 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair .Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by Engr-In-Charge. |
| 51 | Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer) complete all as specified and directed. |
| 52 | M/L PCC (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub bases, 75 mm thick complete. |
| 53 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extrasand |
| 54 | M&L For Type B1 1:2:4 (12.5 mm graded aggregate) Providing, cement concrete in kerbs of mud stops, rounded or chamfered on edgesNote: Contractor shall use Fine aggregate (M Sand) for cement concrete and mortar in masonary |
| 55 | Taking down carefully existing point wiring of any description light, fan,sockets,bells etc) complete including fittings such as terminal boxes, switches, sockets, ceiling rose, lamp holders, brackets sketch fittings, pendants, fan regulartors and making good the disturbed surfaces, walls, floors etc. all as directed by EIC |
| 56 | Taking down old unsv GI earthing |
| 57 | Taking down old unsv MCB DB / main switch incl MCBs / MCCBs complete all as specified and directed |
| 58 | M&L point wiring complete with 1.5 Sqmm single core PVC insulated FRLS cable 1100 Volts grade multistranded copper conductor drawn through in PVC Conduit concealed on underground stone / brick, masonry walls, roofs floors etc including MS terminal boxes fabricaterd out of 1.12mm thick MS sheet sunk type / surface type and laminated top sheet of 2mm thick for housing switches sockets, regulators etc including provn of 1.5 sqmm dia copper conductor for earth wire connected to common dolly for One light point / Fan point / Exhuast Fan / Bell point controlled by one 5 Amps One way switch and making good surfaces all as specified and directed by Engineer-in-Charge. |
| 59 | All as per Item No. 05 but for one 3 pin 5/6 Amps switch socket outlet on same board |
| 60 | All as per Item No. 05 but for one 3 pin 5/6 Amps switch socket outlet on independent board |
| 61 | All as per item No. 05 above but wiring with 4.0 Sq mm and 4.0 sqmm for earth continuity for 3 pin 15/16 Amps switch socket combination |
| 62 | M&L switch piano flush type single pole one way 5 Amps complete all as specified and directed. |
| 63 | M&L switch piano flush type single pole one way 15 Amps complete all as specified and directed. |
| 64 | M&L Switch Socket Combination outlet, multipurpose, 2 pin 5 amps/3 pin 5 amps controled by one switch 5 amps, flush type complete all as specified and directed. |
| 65 | M&L Universal socket outlet with shutter, 5/15 amps controlled by one switch 15 amps, flush type complete all as specified and directed. |
| 66 | S&F Electronic type Modular fan step regulator 120W, 2 module AC 240 V all as specified and directed |
| 67 | M&L lamp holder insulated body with back plate suitable for battern fittings |
| 68 | supply and fix LED Lamp Retro fit type 9 watts 230 V and all as specified by Engr-in-charge |
| 69 | S&F Ceiling rose surface bakelite 65 x 50 mm 2/3 terminais all as specified |
| 70 | S&F Sheet Modular metal enclosure DB SPN 240 Volts 8 Way single door type with 200 Amps busbar for fixing of MCBs |
| 71 | S&F MCB Single pole and neutral, 40A, 240 Volts AC all as specified |
| 72 | S&F MCB Single pole, 5-32A, 240 Volts AC all as specified |
| 73 | M&L Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge o the plate not less1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No.5 connected to earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40 mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe, GI earth lead all as specified |
| 74 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 75 | S & F in repair 15 Watt LED Bldg security light with a nominal system . The luminaire housing should be made of pressure die cast aluminimum. The total power consumption should not exceed 15W (including driver) pre wired fitted on and including two Nos PVC block of suitable l size and connection up to tube light fitting with connecting up with copper 3 core flexible cord of minimum size 0.5 Sqmm size and testing complete including LED lamp, including taking down old unserviceable fitting any type complete all as specified and as directed. |
| 76 | Disconnecting outer & inner unit of Air-conditioning icluding Voltage stablizer unit of any capacity including cutting of copper tubes including shifting of outer unit from roof of the building with provision of angle iron anchor pickets made out of 25mmX25mmX5mm angle iron with suitable size of MS plate with installation of outer & inner unit of AC with the suitable space for further maintenance including necessary gas charging / topping up R-22 /R32/410C with soldering of copper tubes all as specified and directed. |
| 77 | S&F semi grouting industrial socket & plug powder coated made of CRCA sheet complete box comprised with MCB, SP 32 Amps 12 KAMP returning cap. |
| 78 | S&F service bracket for street light fitting made out of 40mm GI pipe of suitable dia light grade not less than 1.2 mtr long, bent to 115 degree shape, fixed to Pole/Wall in any position with 2 Nos 32 x 6mm GI Clamp, nuts, bolts, washers etc complete all as specified and directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender