Tender For Provn Of Retaining Wall And Hill Slope Stabilization Measures Along Bldg No 2Gl And 21 Gl At Dagshai Under Ge Kasauli
Tender Value
3.96 Crore
Estimated cost
Bid Submission
11 Nov 2026
10 days left
EMD
4.71 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Solan → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Retaining Wall And Hill Slope Stabilization Measures Along Bldg No 2Gl And 21 Gl At Dagshai Under Ge Kasauli
BOQ
| Sl. No. | Item Description |
| 1 | Excavation over areas, not exceeding 1.5 m deep and getting out as in soft/ disintegrated rock complete all as specified and as directed. |
| 2 | M & L plain cement concrete type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 3 | M&L reinforced cement concrete of grade M-25 (design mix) as in foundation bases for columns and mass concrete etc complete all as specified and directed.Note : Injection grouting shall be insured at each construction joint. |
| 4 | M&L reinforced cement concrete of grade M-25 (design mix) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and as directed. |
| 5 | Use and waste form work to sides of concrete foundation, footings, bases of columns, raft and raft beams and soffits (if any) of foundation and similar work, vertical or to batter, to achieve flat rough finished surface of concrete complete all as specified and as directed. |
| 6 | Use and waste form work to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter to achieve fair finished surface to flat concrete surface complete all as specified and directed. |
| 7 | S&F PVC (SWR) pipe, 110 mm bore, single socketed, in any length with rubber ring joints including cutting in pieces as per requirement and fixed into retaining walls and the like as in weep holes complete all as specified and as directed. |
| 8 | M&L for steel deformed bars (TMT bars) 10mm dia and over in reinforcement for concrete, cut to length, bent to required shape including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 9 | M&L Hand packing 40 to 80 mm size broken stone boulders at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed. |
| 10 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed. |
| 11 | Removing excavated material exceeding 1000 metre but not exceeding 1500 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed. |
| 12 | Supplying and fixing/wrapping of non-woven Geo textiles sheet with rawl plug and screws using cup washers or other necessary accessories on retaining wall weep holes or on sub surface drainage pipe including overlapping, realized by thermos binding . Polypropylene non-woven Geo textile shall be of minimum thickness of 0.75mm characteristic opening size of 110 micron and tensile strength of 8 kN/m complete all as specified and directed. |
| 13 | M&L for drilling and installation of Self drilling anchor rod (32mm outer dia & 18.5mm inner dia, Yield load > 230kN) including sacrificial drill bit, extension couplings, hexagonal nut, bearing/washer plate including cement grouting upto full length with OPC grade 53 using admixture complete all as per specifications and directed.(Note: Sacrificial drill bit, hexagonal nut, bearing/washer plate to be measured separately) Please Enable Macros to View BoQ information |
| 14 | M&L for drilling and installation of Self drilling anchor rod (32mm outer dia & 18.5mm inner dia, Yield load > 230kN) including sacrificial drill bit, extension couplings, hexagonal nut, bearing/washer plate including cement grouting upto full length with OPC grade 53 using admixture complete all as per specifications and directed.(Note: Sacrificial drill bit, hexagonal nut, bearing/washer plate to be measured separately) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender