Tender For Providing, Fabricating, Supplying And Fixing Of Board Room Table On 4Th Floor At Main Office Building, Jaipur
Tender Value
15.80 Lakhs
Estimated cost
Bid Submission
18 Nov 2026
6 days left
EMD
Ref. Documents
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaipur → Rajasthan
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing, Fabricating, Supplying And Fixing Of Board Room Table On 4Th Floor At Main Office Building, Jaipur
BOQ
| Sl. No. | Item Description |
| 1 | Providing, fabricating, supplying and fixing of Veneer finished conference table of size approx. 70' long and 8' wide in center and 4' wide on ends, made as per approved design and drawing, complete in all respects with specifications as below:1. BASE STRUCTURE :- Base supporting framework made of heavy-duty MS iron structure fabricated from suitable 2\\" X 2\\" size MS box sections main structure and 1\\"x 1\\" pipe for supporting structure of thickness 2.5mm with 100mm x100 mm x 6 mm thick base plates welded to the vertical sections at bottom for maintaining proper line, levels in desired shape ,smooth grinding the edges ,welded junctions, including fixing to concrete with MS hold fasts or dash fasteners and as specified as per site conditions with the flooring.MS framework must support full load of table, wiring system, and accessories. Providing of cross diagonal bracings to avoid lateral movement. Work includes painting the MS surface with 2 or more coats of approved quality synthetic enamel paint over a coat of approved quality primer etc. all complete as per the directions of the Banks Engineer. The tentative weight of ms work will be 1200 kg.2.TOP CONSTRUCTION:- Table top made of 25 mm thick IS 710 grade waterproof plywood properly glued and machine pressed. Top surface finished with 4 mm thick natural veneer. The edge of table is in double layer up to 6\\" depth over it teakwood beading half round/decorative of size approx.. 50x50 mm should be provided on exposed edges finished with PU polish.3.INTEGRETED DESK APRONS: Providing and fixing a hollow apron, a vertical or horizontal modesty panel underneath the top of table consists of box of approximate size 6ft wide x 6 inch deep at centre and reducing appropriately to sides as per drawing attached shall run all along the base for provision of cables of mic system and pop-up box or as per site requirement. The box shall be made up of 12 mm thick IS 710 grade approved make plywood with 4mm thick approved make teak veneer on exposed part and 0.8mm laminate in all internal side duly pressed using Fevicol Hi-Per, Heat X and openable access panel provided in between .4.SIDE & MODESTY:- Bottom vertical members to cover the frame structure made of 12 mm thick IS 710 grade waterproof plywood as required finished with 4 mm veneer externally.5.POLISH & FINISH: - All veneer surfaces to be coated with PU (Polyurethane) polish, including necessary sanding, staining, and finishing coats for smooth matte/ semi-gloss finish as per the manufacturer’s specifications. Table bottom area should be finished with melamine polish of same shade.6.ACCESSORIES: -All required hardware, screws, adhesive, fixtures, and fittings included all complete job in all respects as per site requirement. Table shall be provided with cutting holes and making proper provision of complete audio & electrical system like Mike System, Cable Cubby, Cable Manager, USB Ports, Charging Points etc. as per approved drawing and as per in instruction of Bank's Engineer. Please Enable Macros to View BoQ information |
| 2 | Providing, fabricating, supplying and fixing of Veneer finished conference table of size approx. 70' long and 8' wide in center and 4' wide on ends, made as per approved design and drawing, complete in all respects with specifications as below:1. BASE STRUCTURE :- Base supporting framework made of heavy-duty MS iron structure fabricated from suitable 2\\" X 2\\" size MS box sections main structure and 1\\"x 1\\" pipe for supporting structure of thickness 2.5mm with 100mm x100 mm x 6 mm thick base plates welded to the vertical sections at bottom for maintaining proper line, levels in desired shape ,smooth grinding the edges ,welded junctions, including fixing to concrete with MS hold fasts or dash fasteners and as specified as per site conditions with the flooring.MS framework must support full load of table, wiring system, and accessories. Providing of cross diagonal bracings to avoid lateral movement. Work includes painting the MS surface with 2 or more coats of approved quality synthetic enamel paint over a coat of approved quality primer etc. all complete as per the directions of the Banks Engineer. The tentative weight of ms work will be 1200 kg.2.TOP CONSTRUCTION:- Table top made of 25 mm thick IS 710 grade waterproof plywood properly glued and machine pressed. Top surface finished with 4 mm thick natural veneer. The edge of table is in double layer up to 6\\" depth over it teakwood beading half round/decorative of size approx.. 50x50 mm should be provided on exposed edges finished with PU polish.3.INTEGRETED DESK APRONS: Providing and fixing a hollow apron, a vertical or horizontal modesty panel underneath the top of table consists of box of approximate size 6ft wide x 6 inch deep at centre and reducing appropriately to sides as per drawing attached shall run all along the base for provision of cables of mic system and pop-up box or as per site requirement. The box shall be made up of 12 mm thick IS 710 grade approved make plywood with 4mm thick approved make teak veneer on exposed part and 0.8mm laminate in all internal side duly pressed using Fevicol Hi-Per, Heat X and openable access panel provided in between .4.SIDE & MODESTY:- Bottom vertical members to cover the frame structure made of 12 mm thick IS 710 grade waterproof plywood as required finished with 4 mm veneer externally.5.POLISH & FINISH: - All veneer surfaces to be coated with PU (Polyurethane) polish, including necessary sanding, staining, and finishing coats for smooth matte/ semi-gloss finish as per the manufacturer’s specifications. Table bottom area should be finished with melamine polish of same shade.6.ACCESSORIES: -All required hardware, screws, adhesive, fixtures, and fittings included all complete job in all respects as per site requirement. Table shall be provided with cutting holes and making proper provision of complete audio & electrical system like Mike System, Cable Cubby, Cable Manager, USB Ports, Charging Points etc. as per approved drawing and as per in instruction of Bank's Engineer. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender