Tender For Special Repair To Bldg No P-18 (Mes Office ) And Certain Misc Works At Af Stn Kanheri Hills And Site P Under Ge (Af) Thane
Tender Value
39.40 Lakhs
Estimated cost
Bid Submission
16 Nov 2026
17 days left
EMD
78800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thane → Maharashtra
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No P-18 (Mes Office ) And Certain Misc Works At Af Stn Kanheri Hills And Site P Under Ge (Af) Thane
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement morter beddind (but not backing removing seviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge. |
| 2 | Material and labour for non-skid coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exceeding 0.06 Sqm but not exce 0.11 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick screed bed or bedding layer in CM(1:6) complete all as specified and directed by Engr-in-Charge. |
| 3 | Material and labour for Glazed ceramic tiles in vertical surface 350x 250x7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the colour tiles over and including 10mm thick rendering in CM(1:4) complete all as specified and directed by Engr-in-Charge. |
| 4 | M&L for Vitrified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and directed by Engr-in-Charge. |
| 5 | Demolition of un-reinforced cement concrete in any position complete all as specified and directed by Engr-in-Charge. |
| 6 | M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints complete all as specified and directed by Engr-in-Charge. |
| 7 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor complete all as specified and directed by Engr-in-Charge. |
| 8 | M&L for machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm thick screed bed in CM 1:4 for laying floor finishes complete all as specified and directed by Engr-in-Charge. |
| 9 | Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size n.exc.1.50 Sqm each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed by Engr-in-Charge. |
| 10 | All as per item above herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each complete all as specified and directed by Engr-in-Charge. |
| 11 | S&F IInd class hard wood plain, solid, straight chowkat and frame wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-Charge. |
| 12 | S&F for 30 mm thick IInd class HW rail and style plain framed panelled shutter (Two panel) with lock rail and panel of 9mm BWP,commercial ply or 12mm veneered particle beard with commercial veneering on both faces. The size of rail and stile as per IS :1003 (Part-I) kiln and chemically pressure treated complete all as specified and directed by Engr-in-Charge. |
| 13 | S&F for 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified complete all as specified and directed by Engr-in-Charge. |
| 14 | S&F for 150 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed by Engr-in-Charge. |
| 15 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge. |
| 16 | M&L for Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 17 | M&L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge. |
| 18 | S&F solid PVC solid door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling and fixing in opening with stainless steel screws of required size complete all as specified and directed by Engr-in-Charge. |
| 19 | S&f factory Made Solid PVC Moulded Door Shutter,with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing. Including 3 Nos of stainless steel 100 mm size hinges, 2 Nos of aluminium 100 mm size handles, 2 Nos of aluminium tower bolt 100 mm size complete all as specified and directed by Engr-in-Charge. |
| 20 | Taking down and re-fixing of aluminium anodized windows along with necessary accessories/ fittings. The windows shall be re-fixed after replacement of broken Cuddapah stone, aluminium sections, and after rectification of rollers, wire mesh, window panes, etc. Note: All new items used in the rectification work shall be paid for separately complete all as specified and directed by Engr-in-Charge. |
| 21 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket tc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, luminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the complete all as specified and directed by Engr-in-Charge. |
| 22 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM Rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings complete all as specified and directed by Engr-in-Charge. |
| 23 | M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and complete all as specified and directed by Engr-in-Charge. |
| 24 | S&F for providing and fixing zinc alloy roller for sliding window/ aluminium sections with necessary screws etc complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F for Zinc alloy (powder coated) casement lock for windows with necessary screws etc complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge. |
| 27 | S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading complete all as specified and directed by Engr-in-Charge. |
| 28 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads exc 1.5 sqm complete all as specified and directed by Engr-in-Charge. |
| 29 | S&F sheet glass ordinary quality 3.00mm thick and glazing with oil putty or aluminium/rubber beading in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge. |
| 30 | S&F figured glass, pin-headed type 3.00 mm thick and glazing with oil putty or aluminium/rubber beading in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F in repair, Drapery curtain rod/ Harrison rails of anodised aluminium alloy complete with MS brackets golden colour rings and sode caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and as directed by Engineer-in-charge |
| 32 | Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed by Engr-in-Charge. |
| 33 | Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge. |
| 35 | S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge. |
| 36 | Fixing only, after cleaning old steel water tubing, 15mm bore and connections in new or old position using new fittings complete all as specified and directed by Engr-in-Charge. |
| 37 | Fixing only, after cleaning old steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified and directed by Engr-in-Charge. |
| 38 | S&F in repair 600x450 mm beveled edge looking mirror of selected quality glass and backing with 6mm thick AC building board and fixed to wall with PVC rawl plugs with chromium plated brass screws and cup washers as in repair complete all as specified and directed by Engr-in-Charge. |
| 39 | S&F in repair Towel rail, 19mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified and directed by Engr-in-Charge. |
| 40 | S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F in repair 1000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified and directed by Engr-in-Charge. |
| 42 | S&F 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed by Engr-in-Charge. |
| 43 | S&F in repair stop cock 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe etc complete all as specified and directed by Engr-in-Charge. |
| 44 | S&F in repair Bib tap of CP brass, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge. |
| 45 | S&F in repair Viterous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed by Engr-in-Charge. |
| 46 | M&L in repairs orrisa pattern viterious china ware water closet white glazed of pan size 580x440mm with integral foot rest fixed flushed pipe including all joints and making good to the floor complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F in repair vitreous china wash hand basin white flat back size 550 X 400 mm excluding taps waste chain and plug and porcelain stopper but including brackets, waste coupling and waste pipe complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F 15mm dia long neck pillar tap chromium plated cast copper alloy with capstan head, fancy type screwed down high pressure with or with out letters Hot or cold with long screwed for iron pipe complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F PVC connections 15mm size with PTMT nuts of length 450 mm etc suitable for 15mm bore of pipe complete all as specified and directed by Engr-in-Charge. |
| 50 | S&F 50 mm Low density polyethelne (LDPE) pipes of pressure rating 6kgf/sq. cm complete all as specified and directed by Engr-in-Charge. |
| 51 | S&F in Repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in complete all as specified and directed by Engr-in-Charge. |
| 52 | Dismantling CI pipe alongwith fittings of 75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. (fitting measured separately) complete all as specified and directed by Engr-in-Charge. |
| 54 | S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent including jointing to waste pipe in run lead as in repairs complete all as specified and directed by Engr-in-Charge. |
| 55 | S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and directed by Engr-in-Charge. |
| 56 | S&F PVC (SWR) junction, single 'T' (equal or unequal) 75 mm dia complete all as specified and directed by Engr-in-Charge. |
| 57 | S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes as in repair complete all as specified and directed by Engr-in-Charge. |
| 58 | S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified and directed by Engr-in-Charge. |
| 59 | S&F PVC (SWR) junction, single 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F 110mm dia (SWR) vent cowl complete all as specified and directed by Engr-in-Charge. |
| 61 | S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed by Engr-in-Charge. |
| 62 | S&F in repair grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and directed by Engr-in-Charge. |
| 63 | M&L for Surface preparation of non structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer -in-charge (including removal of external plaster, wherever exists) COST inclusive of transportation, labour, conveying debris away from the out side of MD land, tools and tackles, lead and lift etc including necessery scaffolding ,form work etc, complete all as specified and directed by Engr-in-Charge. |
| 64 | Providing and laying Renderoc SP-40 shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortor supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt. 116) -> 20 MPa at 1 day & > 45 MPa at 28 days. Tensile strength (BS 63199 Pt7)>2.5 Mpa at 28 Days, Flexural strength (BS 6319 Pt.3)>7 Mpa at 28 Days, During Shrinkage to ASTM C157-93, 28 days<1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25 ltr to 4.5 ltr, mixed with suitable container with heavy duty slow speed mixer machine to achieve lump free mortor consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slab, piles etc, where tha thickness of application is less then 50 mm in patch as per specification after applying bounding coat item rate is inclusive of materials all labour tools and tackles, scaffloding and transportation etc. complete all as specified and directed by Engr-in-Charge. |
| 65 | Removal of damaged structural concrete along with loose damaged and crecked concrete/ cover concrete at all specified locations up to beyond the corroged steel reinforcements to a depth of 10 mm minimum behind the reinforcement by chhpping/ hacking with chisel and hammer or by mechinical means like chisel hammer, pneumatic chippers incl high pressure water jetting to chipped concrete and reinforcement and removal and disposal of debris within owners premises incl. all plants and machineries complete all as specified and directed by Engr-in-Charge. |
| 66 | Cleaning as directed & specified all rust/scales/ corrosion from reinforcement bars using rust remover Reebaklens RR- Rust remover, cleaning and etching agent supplied in 1/2, 1 and 5 ltr containers, having specific gravity 1.16-1.22 @ 25 degree celcius, reebaklens RR cleaning agent is a combination of acid based materials, corrosion inhibitors and dispersing agents and is supplied as a clear green solution application of reebaklens RR with brush for complete wetting of rusted metal surface and allowed to react it for 16-24 hours followed by cleaning the surface with wire brush and washing surface with fresh water as required to exposed reinforcement bars complete all as specified and directed by Engr-in-Charge. |
| 67 | Providing and applying inhibition coats/system to exposed reinforcement bars after drying & also mew bars after cleaning & removing scales and rust completely as specified. Nitozinc primer Two component epoxy zincrich primer supplied in 1 and 5 ltrs pack, two component system based on metallic zink and epoxy resin which on mixing gives a grey coloured liquid. An anti corrosive coat contents active 'Zinc-rich' system which combates corrosion by electro chemical means. having specific gravity of 1.75, adhesive bond strength > 1.5N/mm2 solid content 60%, 40 microns DFT, Fully dry/Rrcoatable-45 minutes to 1 hour. Typical application includes surface preparations by cleaning steel surface to a bright condition paying particuler attention to the back of exposed steel bars, mixed two components slow speed heavy duty drill fitted with a paddle, applying unbroken coat with suitable brush and alloy to dry, after 30 mins apply second coat to ensure complete cover to exposed steel/ reber etc complete. Total dry film thickness is 40 microns complete all as specified and directed by Engr-in-Charge. |
| 68 | Cutting, febrication new reinforcement FE-500 and fixing with old existing reinforcement which was reduced to 20 % or more of its original dia as provided in original structure and additional steels as directed by EIC to be fixed with chemical anchor grout lokfix E55- styrene free vinyl-ester resin based cartridge syatem for anchoring reinforcement supplied in 300 ML cartidge with a single mixture nozzle, application inclueds drilling hole close to old reinforcement bar with suitable drill as per dia of the bars, cleaning the hole with wire brush and compressed air, putting lokfix E55 with gun followed by placing rebar with slide rotational motion to avoid air void formation etc complete all as specified and directed by Engr-in-Charge. |
| 69 | Drilling holes in to existing concrete substrate for anchoring of new rebars with 10 mm dia shear connectors at 0.5 mtr c/c and fixing with chemical anchor lokfix E55-styrene free vinylester resin based cartridge system for anchoring reinforcement supplied in 300 ml cartidge with a single mixture nozzle, shall be tested in accordance European approval to EAD-33087-00-0601 for use in post-installed rebar, which suspersedes ETAG 001 TR 023 (rebar), LEED compliant VOC Level, Fibre resistance < 120Mins, Seismic C1 testing as part of EAD 330499-00-0601 for specific fastening sizes etc. Typical application inclueds drilling holes 14mm dia and 90mm deep as per manufactures recommandation, cleaning the hole with wire brush and compressed air, putting lokfix E55 with gun followed by placing shear connector with slide rotational motion to avoid air void formation etc complete all as specified and directed by Engr-in-Charge. |
| 70 | Providing and applying Renderoc RG-Polymer modified micro-concrete supplied in 25 kg moisture resistant bag should possess following properties when mixed with clean water at w:p ratio 0.16, such as compressive strength (BS 4551-80)-50 Mpa at 28 Days, Tensile strength -2Mpa @ 28 days, flextural strength (BS 4551-80) Mpa at 28 days, Young's modulus-25 KN/mm2, Expansion characteristics (ASTM C827-1987) unrestrained expansion 1 to 4% pressure approx. 0.004 N/mm2, Thermal conductivity-1.5 W/m degree cel. fire rating (EN 1504 cl 5.5)-class A1, fresh wet density (mixed density @27 degree cel. ) -2100-2200 Kg/m3. Typical application inclued mixing whole bag with clean water about 4 litres mixing in suitable container with heavy duty slow speed mixture machine to produce uniform free flowing mix, pouring the same in to the form work using suitable arrangement or if required using pupping device for uniform flow of micro concrete. The side shuttering can be removed after 3 days and the bottom shuttering after 7 days ensuring proper bond between the micro concrete and existing concrete substrate. item rate ia inclusive of materials and labour, tools and tackles, scaffolding and transportation etc. complete all as specified and directed by Engr-in-Charge. |
| 71 | Providing and applying bond coat on the prepared surface to receive polymer modified mortor/ polymer modified micro concrete , with two components epoxy based bonding coat Nitobound EP- Epoxy rasin concrete bonding agents supplied in 1/2, 1 and 4 ltr Packs, having specific gravity 1.15 to 1.2 gm/cc, Compressive strength (BS 6319 Pt 2)-50 Mpa at 7 Days, Tensile strength (BS 6319 Pt.7)-20Mpa @ 7 days, flextural strength (BS 6319 Pt.3) -35 Mpa at 7 days, Shear strength (BS-6319 Pt.4) 10 MPa at 7 Days having an over lay time of 6 hrs and 30 degree cel. high bond strength : bound strengthis more then the tensile strength of goood quality concrete barrier coat acts as a 'barrier coat to the migration of chloride inos from host concrete. Laying of reinstatement polymer modified mortor or micro concrete shall be completed within over lay time of bounding coat. The bond coat act as a bonding coat between old ad new concrete. Typical application includes cleaning all loose dust, dirt, grease from host concrete surface by suitable means, mixing both components of bond by heavy duty slow speed mixer until a unifrom consistency, apply unbroken coat of Nitobond EP with stiff brush covering complete area of patch repair before plcing mortor or nicro concrete. Item rate inclusive of materials all labour, tools and tackles, scaffolding and transportation etc complete all as specified and directed by Engr-in-Charge. |
| 72 | Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge. |
| 73 | M&L for rendering 5mm thick in CM 1:4 on fair faces of concrete as in ceiling of slab finished even and smooth without using extra complete all as specified and directed by Engr-in-Charge. |
| 74 | M&L for rendering 15mm thick in cm 1:6 on fair faces of brick work or concrete surfaces of wall and finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 75 | M & L for rendering 20 mm thick in cement mortar (15 mm thick 1:6 as backing coat and 5mm thick1:4 finishing coat) on fair faces of brick work or concrete surfaces including finished even and smooth without using extra cement with using water proofing compound (water proofing compound shall be measured and paid seperately) complete all as specified and directed by Engr-in-Charge. |
| 76 | M&L for applying Two or more coats of 100% Premium acrylic emulsion paint Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces in Camouflage pattern. complete all as specified and directed by Engr-in-Charge. |
| 77 | M&L for Preparation of newly plastered surfaces of walls & applying two coats of OBD on chalk whiting on plastered surfases complete all as specified and directed by Engr-in-Charge. |
| 78 | M&L for Preparation of newly plastered surfaces of ceiling & applying three coats coats of white wash complete all as specified and directed by Engr-in-Charge. |
| 79 | M&L for Washing, rubbing down and stopping of distempered and painted surfaces of wall and applying one coat of distemper oil-emulsion on walls complete all as specified and directed by Engr-in-Charge. |
| 80 | M&L for washing,rubbing down and stopping of distempered and painted surfaces of ceiling and applying one coat of distemper oil-emulsion on ceiling complete all as specified and directed by Engr-in-Charge. |
| 81 | M&L for 3mm thick one coat of wall care putty on wall complete all as specified and directed by Engr-in-Charge. |
| 82 | M&L for 3mm thick one coat of wall care putty on ceiling complete all as specified and directed by Engr-in-Charge. |
| 83 | M&L Preparation of old treated brick or concrete wall, cleaning the surface from all loose dirt chalk greese fungi, algai flakes and applying one coats of acrylic paint weather proof exterior grade with camouflage pattern complete all as specified and directed by engineer-in-charge. Note: Painting surface may not be directly accessible due to some obstructions, Hence qoated rates shall include necessary scaffholding etc complete all as specified and directed by Engr-in-Charge. |
| 84 | Labour only of taking up or down steel tubing and connections of 20mm bore of pipe including cleaning and refixing in the same position as in wall/ roof /walls, etc during carrying out of water proofing treatment without damaging to existing services, etc. complete all as specified and directed by Engr-in-Charge. |
| 85 | Labour only for disconnecting existing over head tanks of capacity exc.500 and n.exc 1000 ltr, setting aside or lowering if required for repair of roof water proofing treatment and hoisting, reconnecting and re-fixing in position after necessary work without damaging to existing services etc.complete all as specified and directed by Engr-in-Charge. |
| 86 | Removing existing water proofing treatment where so ever exist (except concretepadding) and removing debris/rubbish off the sitecomplete all as specified and directed by Engr-in-Charge. |
| 87 | M&L for 10 mm thick plaster in roof surface in CM 1:3 mixed with integral water proofing liquid admixture as per manufacturer's instructions complete all as specified and directed by Engr-in-Charge. |
| 88 | Material and labour for water proofing treatment with APP based standard membrane over in roof with the following courses of treatment for:-(a) Apply bituminous primer (IS 3384) @ 0.40 Kg per sqm of the surface area including cleaning the surfaces complete all as specified.(MAKE : TEXSA/BITUMAT/BITUNIL/SIKA)(b) Apply APP plastomeric bitumen based mineral finished water proofing membrane polyester reinforced(3 Kg/Sqm) with 10cm over laps and torch bonded at joints including surface preparation before and after application of treatment as per manufactures instruction complete all as specified. (Make of APP Membrane: Moply FP 3 mm mineral of TEXA/WP Shield 103 PM of SIKA or Equivalent material of BITUNIL/BITUMAT. (c) The entire surface of finished APP membrane shall finally be painted with one coat of Solar reflective bituminous aluminium paint @ 0.1 ltr per Square Meter and other as prescribed by manufacturer ,complete complete all as specified and directed by Engr-in-Charge. |
| 89 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engr-in-Charge. |
| 90 | S & F for Rolled sections as in main andcross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe-410 W(Gde E-250) quality B complete all as specified and directed by Engr-in-Charge. |
| 91 | Dismentling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and directed by Engr-in-Charge. |
| 92 | S & F anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm incl hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engr-in-Charge. |
| 93 | M&L for 8 mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws complete all as specified and directed by Engr-in-Charge. |
| 94 | Demolition of reinforced cement concrete of any description and in any position provided as in roof padding, roof curb etc complete all as specified and as directed. Note: - (a) Demolition should be done carefully to roof slab. (b) Any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department.(c) Disposal of debris/retrieved materials shall be thrown out of site at place as directed by the Engineer-in-Charge. complete all as specified and directed by Engr-In-Charge. |
| 95 | Material and labour for providing plain cement concrete type B- 1, (1:2:4) using 20mm graded stone aggregate as in roof padding , in roofkerbs or mud stops, rounded or chamfered on edges laid in slope as per requirement mixed with integral water proofing liquid admixture as per manufacturer's instructions complete all as specified and as directed.Note : (i) Minimum thickness of PCC shall be 50mm. (ii) Integral water proofing liquid admixture shall be measured and paid separately under appropriate item here in after complete all as specified and directed by Engr-In-Charge. |
| 96 | Supply only integral water proofing compound complete all as specified and directed by Engr-In-Charge. |
| 97 | M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, and filling solidly with a hot mixture of bitumen and clean dry and 1:1 ( by weight) complete all as specified and directed by Engr-In-Charge. |
| 98 | S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed by Engr-In-Charge. |
| 99 | M&L for 15mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-In-Charge. |
| 100 | M&L for Preparation of newly plastered surfaces of Wall & applying two coats coats of white wash complete all as specified and directed by Engr-In-Charge. |
| 101 | M&L for Preparation of old decorated surfaces on ceiling and applying one coat of white lime wash including cornice and pillars etc complete all as specified and directed by Engr-In-Charge. |
| 102 | S&F in repair Bib tap of CP brass, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engr-in-Charge. |
| 103 | Taking down shutter of any description of exceeding 1 sqm but not exc 2 Sqm complete all as specified and directed by Engr-in-Charge. |
| 104 | S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixingclips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge. |
| 105 | Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth and getting out in hard and dense soil complete all as specified and directed by Engr-in-Charge. |
| 106 | Returning,filling in ,including spreading,levelling ,watering and well ramming in layers not exe 25cm complete all as specified and directed by Engr-in-Charge. |
| 107 | Removing excavated material n, exe 50m and depositing where directedat a level n, exe 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 108 | M&l for PCC type D-2(1:4:8) using 40mm graded crushed aggregate as mass conc and filling of foundation complete all as specified and directed by Engr-in-Charge. |
| 109 | M&L Hardcore with boken stone of gauge n exc 63 mm, deposited, spread and levelled and layer n exc 15 cm thick, water and rolled /rammed to a true surface complete all as specified and directed by Engr-in-Charge. |
| 110 | Material and labour for brick work with sub class \\"B\\" bricks, straight or curved on plan exceeding 6m mean radius built in cement Mortar 1:4 complete all as specified and directed by Engr-in-Charge. |
| 111 | M&L for 15 mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and directed by Engr-in-Charge. |
| 112 | M&L for three coats of white wash on newly plastered surfaces of wall incl preperaton complete all as specified and directed by Engr-in-Charge. |
| 113 | M & L Reinforced cement concrete ( Nominal mix) in type B1 1:2:4( 20 mm graded aggregate) Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr-in-Charge. |
| 114 | M & L for form work to sides and soffits of floor or beams etc complete all as specified and directed by Engr-in-Charge. |
| 115 | M & L for mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking bending spirally for hooping for column hooking end complete all as specified and directed by Engr-in-Charge. |
| 116 | M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to match with shade of granite over 20mm thick screed (1:4) bed complete all as specified and directed by Engr-in-Charge. |
| 117 | M&L for Cement concrete 40mm thick type B-1, 1:2:4 (20mm graded aggregate) as in base concrete to receive tile complete all as specified and directed by Engr-in-Charge. |
| 118 | M&L for Machine cut kota stone slab flooring 25mm thick over and including 15mm thick 1:4 cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20mm thick screed bed (1:4) complete all as specified and directed by Engr-in-Charge. |
| 119 | S&F for 32mm dia Waste coupling of PTMT (half or full threaded). (Minimum weight 32mm 45gms/40mm-60 gm complete all as specified and directed by Engr-in-Charge. |
| 120 | S&F PVC waste pipe, 32mm bore suitable to waste coupling pipe attach with rubber ring joints fixed to waste coupling of sinks/WHBs complete all as specified and directed by Engr-in-Charge. |
| 121 | Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft and loose soil complete all as specified and directed by Engr-In-Charge. |
| 122 | Cement concrete type B2, 1:2:4 (40mm graded aggregate) for post complete all as specified and directed by Engr-In-Charge. |
| 123 | Formwork to sides of post flats rough finished surface of concrete complete all as specified and directed by Engr-In-Charge. |
| 124 | Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C2 for 300mm dia pipe complete all as specified and directed by Engr-In-Charge. |
| 125 | Reinforced concrete pipes, class NP2, 300mm dia, laid and jointed complete all as specified and directed by Engr-In-Charge. |
| 126 | M&L sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engr-In-Charge. |
| 127 | M&L Machine pressed precast concrete interlocking paver block with grey cement and no pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed by Engr-In-Charge. |
| 128 | Pre-cast cement concrete block of type C1 1:3:6 (20mm graded aggregate) masonry with solid blocks, exc. 10 cm in width and setting in mortar 1:6, complete all as specified and directed by Engr-In-Charge. |
| 129 | S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed by Engr-In-Charge. |
| 130 | S&F pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-In-Charge. |
| 131 | Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-In-Charge. |
| 132 | Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.50 cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, including removing complete all as specified and directed by Engr-In-Charge. |
| 133 | S&F PPGL pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-In-Charge. |
| 134 | S&F mild steel screw bolts of 11 to 18 diameter of neck in mm (machine made) with hexagonal or square heads at one end and screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut nexc 5 cm long complete all as specified and directed by Engr-In-Charge. |
| 135 | M&L MS work flat iron, MS plates as in brackets, cleats, fasteners, wind ties, supports, base for posts etcwith riveted, bolted or welded attachment complete all as specified and directed by Engr-In-Charge. |
| 136 | S&F for Anodised aluminium with powder coating (minimum thickness of powder coating 50 micron) window and ventilator shutters fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed by Engr-In-Charge. |
| 137 | S&F sheet glass ordinary quality 4.8mm thick and glazing with oil putty or wooden beads in square n exc 0.5sqm in each panel (beads will be measured and paid under separate item) complete all as specified and directed by Engr-In-Charge. |
| 138 | S&F sheet glass ordinary quality 4.8mm thick and glazing with oil putty or wooden beads in square exc 0.5sqm in each panel (beads will be measured and paid under separate item) complete all as specified and directed by Engr-In-Charge. |
| 139 | S&F for Solar control black film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engr-In-Charge. |
| 140 | S & F for Gear operated Steel rolling shutters 1.25mm thick MS sheet laths, ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, gear operated type with bevel gear box and crank handle complete all as specified and directed by Engr-In-Charge. |
| 141 | S & F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by Engr-In-Charge. |
| 142 | S & F for Ball bearing for rolling shutters complete all as specified and directed by Engr-In-Charge. |
| 143 | S & F 3mm thick aluminium composit panel as in False ceiling in any shape/ design including aluminium anodised frame works for fixing of panels and filling the gaps of panel with epoxy solvent complete all as specified as per manufactures instruction and standard design practice complete all as specified and directed by Engr-In-Charge. |
| 144 | Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and making good disturbed surfaces of walls, floors etc to match with existing surfaces of colour shade complete all as specified and directed by Engr-In-Charge. |
| 145 | Material and labour for Point wiring with 1.5 sqmm copper conductor single core core , cable (multistrand) PVC insulated FRLS(unsheathed) concealed drawing in existing PVC conduit/casing caping 25 mm dia, having wall thickness not less than 2 mm for one light pont, controlled by one , one way switch , including 1.5 sqmm PVC insulated FRLS (unsheathed ) copper conductor continuous earth wire complete all as specified and directed by Engr-In-Charge. |
| 146 | All as per item No145 above, but for One fan point controlled by one switch complete all as specified and directed by Engr-In-Charge. |
| 147 | All as per item No 145 above, but for One 3 pin 6 amps socket out let point controlled by one 6 amps switch on independent board complete all as specified and directed by Engr-In-Charge. |
| 148 | All as per item No 145 above, but for One 3 pin 6 amps socket point controlled by one 6 amps switch on same board complete all as specified and directed by Engr-In-Charge. |
| 149 | All as per item No.145 above, but with 2.5 sqmm for One 3 pin 16 amps socket outlet point controlled by one 16 amps switch on on Ind board complete all as specified and directed by Engr-In-Charge. |
| 150 | Supply & fix modular switch 6 Amps, one way, one module complete all as specified and directed by Engr-In-Charge. |
| 151 | Supply & fix modular switch 16 Amps,one way, one module complete all as specified and directed complete all as specified and directed by Engr-In-Charge. |
| 152 | Supply & fix modular socket 6 A/16 Amps, 6 Pin combined, two module complete all as specified and directed by Engr-In-Charge. |
| 153 | Supply & fix modular socket 6 A, 3 Pin combined, two module complete all as specified and directed by Engr-In-Charge. |
| 154 | Supply & fix modular fan step regulator,120 two module complete all as specified and directed by Engr-In-Charge. |
| 155 | Supply & fix ceiling rose, 3 terminal, PVC/polycarbonate body complete all as specified and directed by Engr-In-Charge. |
| 156 | Supply & fix in repair LED lights 1x20 watt ,220 V, AC decorative box type with driver , holder including LED tube light connecteing up with three core flexible copper conductor cable of suitable size from ceiling rose including connector block etc.and necessary fixing arrangement at any height and removing old unserviceable item complete all as specified and directed by Engr-In-Charge. |
| 157 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-In-Charge. |
| 158 | Supply & fix in repair recess mounting high lumen LED flat panel 2'X2' 36Watt, slim fit,white powder coated CRCA housing with highpower LEDs , aluminium front frame with flat white high transmission acrylic cover, internally prewired, 230V,complete with all accessories such as electronic driver,LED strip,connector block etc.and necessary fixing arrangement at any height and removing old unserviceable item complete all as specified and directed by Engr-In-Charge. |
| 159 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300MM sweep with, blades, and frame and louvers including removing of existing complete all as specified and directed by Engr-In-Charge. |
| 160 | Supply and fix in repairs MCB distribution board SPN 12 way 240 volts, double door with IP 42 protection duly painted with epoxy based powder coated painting suitable for mounting MCB DP/SPN as incomer and MCB SP/DP as outgoings complete with 200 Amps rated busbar, neutral bar, earth bar connecting cable links with top and bottom removable gland plate including removing old unserviceable item complete all as specified and directed by Engr-In-Charge. |
| 161 | Supply and fix in repair MCB SP 6 to 32 Amps,10 KA, \\"C\\" series, 240 volts complete all as specified and directed by Engr-In-Charge. |
| 162 | pply & fix in repair MCB SPN 40 Amps 10 KA, \\"C\\" series, 240 volts complete all as specified and directed by Engr-In-Charge. |
| 163 | Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level, earth plate surrounded by and packed with 15 cm thick layer of char coal dust and common salt, earth lead GI wire 4.00 mm dia by means of bolts, Nuts, Check Nuts and washers of galvanized iron and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 & RCC cover all as specified & shown in elect plate No. 3 of SSR part I of 2010 including testing on completion including taking down existing unserviceable earthing complete all as specified and directed by Engr-In-Charge. |
| 164 | Supply,lay and testing in replacement LT cable XLPE insulated,galvanised steel strip armoured,1100 volts grade with multistranded aluminium conductor of cross-sectional area 16 sqmm; 2 core laid in trenches/pipes/ducts/walls and connection with necessary cable lugs and glands, nuts, bolts and washers etc and testing including removing old unserviceable item complete all as specified and directed by Engr-In-Charge. |
| 165 | M&L for point wiring in casing caping complete with 1.5 Sqmm single core multistranded copper conductor FRLSH PVC insulated and unsheathed cable 1100 V grade confirming to IS 694 drawn through PVC casing caping of suitable size heavy grade ISI marked including necessary casing caping accessories, sunken type pressed steel terminal boxes with plastic laminated sheet of approved shade 3mm thick including 1.5 mm PVC insulated flame retardant copper conductor as in continious earth wire complete all as specified and directed by Engr-In-Charge. |
| 166 | One ceiling fan & exhaust fan point controlled by one switch complete all as specified and directed by Engr-In-Charge. |
| 167 | Ditto-All as per item No-165 above but with 2.5 Sqmm wire for 15 Amp socket outlet on independent board complete all as specified and directed by Engr-In-Charge. |
| 168 | Supply & Fix switch piano flush button single pole one way 5 Amps, 250 V complete all as specified and directed by Engr-In-Charge. |
| 169 | Supply and Fix switch piano flush button single pole one way 15 Amps, 250 V complete all as specified and directed by Engr-In-Charge. |
| 170 | Supply and Fix socket outlet 2 in 1,6 pin, 5/15Amps flush type 220 V complete all as specified and directed by Engr-In-Charge. |
| 171 | Supply and fixing of ceiling fan 1200 mm sweeep complete with blades , down rods, electronic regulator and accessories , 230 volts , Min air delivery 210 CFM with service value 6.00 BEE , five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engr-In-Charge. |
| 172 | Supply and Install Air circulator ( Industrial fan ) , Pedestal type 18\\" size 450mm Nos of Blades 03 , air delivery 150CMM speed 1400 RPM steel body AC single phase , 230 volts complete with blades , and frame etc complete with colour grey / gold , Model name Thunder storm Pro Make- Crompton complete all as specified and directed by Engr-In-Charge. |
| 173 | M & L for Point wiring complete with 1100 volts grade FRLS insulated unsheathed cable of copper conductor cable multi stranded of size 1.5 Sqmm single one including PVC rigid Casing Caping medium grade of suitable size (not less than 20 mm dia) with all accessories such as bend reducers / MS hooks MS Junction box 1.2mm thick MS pressed sunken terminal boxes of suitable sizes for mounting of switches sockets, fan regulators etc covered with 3.15 mm thick bakelite laminated (Hylem/ Anchor) top cover including continous earth wire size 1.5 Sqmm PVC strandedcopper conductor unsheathed, insulated stranded (Green colour) connected to common earth point dolly, complete all as specified and directed by Engr-In-Charge for the following :- . |
| 174 | One light point control by one switch complete all as specified and directed by Engr-In-Charge. |
| 175 | One 3 pin socket outlet, 5 AMPS, independent with cables 1.5 sqmm size complete all as specified and directed by Engr-In-Charge. |
| 176 | One 3 pin socket outlet, 15 AMPS, independent with cables 2.5 sqmm size PVC Single core, sheathed cable complete all as specified and directed by Engr-In-Charge. |
| 177 | Supply and fixing switch socket combination 2 in 1- 6A flush type complete all as specified and directed by Engr-In-Charge. |
| 178 | Supply and Fixing switch socket combination 3 Pin 16A, flush type complete all as specified and directed by Engr-In-Charge. |
| 179 | Supply and fix MCB DB SPN 4 way double door com complete all as specified and directed by Engr-In-Charge. |
| 180 | Supply install hi wall split unts indoor/ outdoor complete with cordless remote control unit and complete indoor and outdoor units and standard accessories with minimum 3 star rating of capacity 1.5 o TR complete all as specified and directed by Engr-In-Charge. |
| 181 | Material and labour for sub main wiring complete with 2 run of 4 sqmm, single core, copper conductor cable 1100 volts grade FRLS type, PVC flexible multi stranded duly colour coded cable drawn through and and including PVC casing and caping of size 25 mm width or above as required at site and accessories such as tee, corners, overlaping connector etc of suitable size fixed on surface of walls/ roofs / ceilling and including 01 run of 4 sqmm single core, copper conductor cable 1100 volts grade, FRLS type, PVC insulated unsheathed, flexible, multi stranded of green colour as earth continuity conductor connected to common earth dolly including removing old userviceable item complete all as specified and directed by Engr-In-Charge. |
| 182 | Supply and fix in replacement of sheet metal enclosures with two pin and earth plug and socket complete with single pole MCB 20 AMPS complete all as specified and directed by Engr-In-Charge. |
| 183 | Supply and fix AC stand floor / wall mounted complete all as specified and directed by Engr-In-Charge. |
| 184 | Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 volts to 250 volts with out voltage stabilized at 20 volts with accuracy of + 2.5 % and of capacity 5 KVA complete all as specified and directed by Engr-In-Charge. |
| 185 | Supply and fix round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-In-Charge. |
| 186 | Supply and fix MCB distribution board SPN 8 way 240 volts double door with IP 42 protection duly painted with epoxy based powder coated painting suitable for mountng MCB DP / SPN as incomer and MCB SP/DP as outgoing complete with 200 AMPS rated busbar neutral bar, earth bar connecting cable links with top and bottom removable gland plate incuding removing old unserviceable item complete and making good the disturbed surfaces to match with existing complete all as specified and directed by Engr-In-Charge. |
| 187 | Supply and Fix MCB SPN 32 AMPS 10 KA \\"C\\" series 240 VOLTS complete all as specified and directed by Engr-In-Charge. |
| 188 | Supply & fix in repair LED flood light 100 watt 230 V AC outdoor type with impact and corrosion resistant complete with driver and lamp complete all as specified and directed by Engr-In-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender