Tender For Estimate For The Cost Of Maintenance Of Drivers Room And Poly Carbonate Sheet Work In Depot Office Par Uzha Kottayam During 2026-27
Tender Value
Ref. Documents
Estimated cost
Bid Submission
06 Nov 2026
8 days left
EMD
5875
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kottayam → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Estimate For The Cost Of Maintenance Of Drivers Room And Poly Carbonate Sheet Work In Depot Office Par Uzha Kottayam During 2026-27
BOQ
| Sl. No. | Item Description |
| 1 | Maintenance work of drivers room |
| 2 | 14.1.2 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq meters and under,including cutting the patch in proper shape,raking out joints and preparing and plastering the surface of the walls complete,including disposal of rubbish to the dumping ground with in 50 meters lead:cement mortar 1:4(1 cement : 4 coarse sand) |
| 3 | 15.12.1 Dismantling doors,windows and clerestory windows(steel or wood) shutter including chowkhats,architrave,holdfasts etc. complete and stacking within 50 metres lead:of area 3 sq. metres and below |
| 4 | 50.9.1.1 providing wood work in frames of doors,windows,clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & amp:length(hold fast lugs or dash fastener shall be paid for seperately),using good quality Anjili wood/jack wood |
| 5 | 50.9.3.1 Providing and fixing paneled or paneled and glazed shutters for doors,windows and clerestory windows,30 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws,excluding paneling which will be paid for seperately,all complete as per direction of engineer in charge,using Anjili/Jack wood |
| 6 | 50.9.4.1 Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors,windows and clerestory windows(area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjily/jack wood |
| 7 | 21.1.2.2 For shutters of doors,windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required(Fittings shall be paid for seperately)Powder coated aluminium(minimum thickness of powder coating 50 micron) |
| 8 | 21.3.1 Providing and fixing glazing in aluminium door,window,ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc.complete as per the architectural drawings and the directions of engineer-in-charge(Cost of aluminium snap beading shall be paid in basic item):with float glass panes of 4.0 mm thickness(weight not less than 10kg/sqm) |
| 9 | 13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:water thinnable cement primer |
| 10 | 13.111.1 Finishing walls with acrylic smooth exterior paint of required shade:Old work(Two or more coat applied @1.67 ltr/10 sqm)on existing cement paint surface |
| 11 | 13.61.1 painting with synthetic enamel paint of approved brand and manufacture to give an even shade;Two or more coats on new work |
| 12 | Poly Carbonate sheet work |
| 13 | 50.10.1 Steel work in built up GI tubular(round,square or rectangular hollow tubes etc.)trusses etc.,including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer,including welding and bolted with special shaped washers etc.complete |
| 14 | 50.12.2.2 providing & amp;fixing poly carbonate multi wall plain sheet 4 mm thick as approved by the engineer in charge and should be supplied in a single length of 12M or as decide by the engineer in charge.The sheets shall be fixed using self drilling/self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/vertical/curved surfaces,but excluding the cost of purlins,rafters,trusses and including cutting to size and shapes where ever required |
| 15 | 13.52.1 finishing with Epoxy paint(two or more coats)at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat,preparation of surface,etc.complete.On steel work Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender