Tender For Construction Of Reinforced Cement Concrete Building For Training And Conference Hall For Farmers And Officials, Directorate Of Horticulture & Soil Conservation, Imphal East.
Tender Value
6.02 Crore
Estimated cost
Bid Submission
13 Nov 2026
8 days left
EMD
15 Lakhs
Bank guarantee accepted
Document Fee
1500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Imphal West → Manipur
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Reinforced Cement Concrete Building For Training And Conference Hall For Farmers And Officials, Directorate Of Horticulture & Soil Conservation, Imphal East.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 03-Nov-2026 | Corrigendum for Construction of RCC Building for Training and Conference Hall for Farmers and Officials, Directorate of Horticulture and Soil Conservation, Imphal East. | Fee | 13-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | EARTH WORK |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth. 1,5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by the Engineer-in-Charge. All kinds of Soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 4 | Supplying and filling in plinth with sandy soil under floors including, watering, ramming consolidating and dressing complete. |
| 5 | Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 6 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 7 | CONCRETE WORK |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering; 1:4:8 (1 Cement :4 coarse sand :8 stone aggregate 40 mm) |
| 9 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size). |
| 10 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification. |
| 11 | Applying a coat of residual petroleum bitumen of grade VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 12 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 13 | REINFORCED CEMENT CONCRETE |
| 14 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland- Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. |
| 15 | All work upto plinth level; Concrete of M-25 grade with minimum cement content of 300 kg/cum. |
| 16 | All works above plinth level upto floor V level; Concrete of M25 grade with minimum cement content of 330 kg /cum |
| 17 | FORMWORK |
| 18 | Centering and shuttering including strutting, propping, etc. and removal of form for: |
| 19 | Foundations, footings, bases of columns for mass concrete. |
| 20 | Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 21 | Suspended floors, roofs, landings, balconies and access platform |
| 22 | Lintels, beams, plinth beams, girders, bressumers and cantilevers. |
| 23 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 24 | Stairs, (excluding landings) except spiral-staircases. |
| 25 | Weather shade, Chajjas, corbels etc., Including edges |
| 26 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. ; Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 27 | Reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete. Above Plinth level ; Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 28 | MASONRY WORK |
| 29 | Brick work with F.P.S. bricks of class designation 7.5 In foundation and plinth in ; Cement mortar 1:4 (1cement: 4 coarse sand) |
| 30 | Providing and laying autoclaved aerated cement blocks masonry with 100mm thick AAC blocks in super structure above plinth level upto floor V level in cement mortar 1:4 (1 cement: 4 coarse sand ) The rate includes providing and placing in position 2 Nos. 6 mm dia M.S. bars at every thirdcourse of masonry work. |
| 31 | WOOD WORK |
| 32 | Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in positfon with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener Shall be paid for separately ; Local best quality Teak wood |
| 33 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick ; Local best quality Teak wood |
| 34 | Providing and fixing teak wood lipping of size 25x3 mm in pelmet |
| 35 | Providing and fixing ISI marked oxidised M.S.sliding door bolts With screws etc. complete ; 300x16 mm |
| 36 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, Barrel type) with necessary screws etc. complete: 250 x 10 mm |
| 37 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete ; 125mm |
| 38 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, screws etc. to suit shutter thickness complete |
| 39 | STEEL WORK |
| 40 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete ; Fixed to openings /wooden frames with rawl plugs screws .etc. |
| 41 | Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete; Hot finished, seamless type tubes. |
| 42 | Steel work welded in built up section/framed work including Cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. as required. ; In grating, frames, guard bar, railing, brackets, gates andsimilar works. |
| 43 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engiheer-in-charge, (for payment purpose ohly weight of stainless Steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 44 | FLOORING |
| 45 | Providing and fixing 18mm thick gang saw cut . mirror polished (premoulded and prepolished) machine cut for kitchen platforms,vanity counters ,window sills , facias and similar locations of required • size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement: 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. ; Area of slab over 0.50 sqm. |
| 46 | 52 mm thick cement concrete .flooring with Concrete hardener topping under layer 40 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume .hardening compound is mixed @ 2 litre per 50kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 47 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 :4 (1 cement: 4 coarse sand): 25 mm thick. |
| 48 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 49 | Providing and laying vitrified floor tiles, in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0,08% and conforming to IS : 15622 of approved make in all colours and T . shades, laid on 20mm thick cementmortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc; complete. |
| 50 | CLADDING WORK |
| 51 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :- 15622 (thickness to be specified by the manufacture of approved make in all colours; shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with-grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 52 | ROOFING |
| 53 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.l. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required ; 1.00mm thick with zinc coating not less than 275gm/m2 |
| 54 | Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive), as per IS: 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels45x15x0.9mm running at the spacing of 1200mm centre to centre; to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.l. intermediate channel with |
| 55 | connecting clips made out of 2.64mm diax230mm long G.l. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre,with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng to a flush finish of tapered and square edges of the board with recommended jointing compoundjointing tapes, finishing with jointing compund in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board,all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed,all complete as per drawings, and specification and direction of theEngineer in Charge but excluding the cost of painting with : Fully Perforated Gypsum Plaster Board of size 1200 x 2400 x 12.5 m having approx. 15% perforated size and pattern as approved by the Engineer-in-charge and as per manufacter's specification, with all 4 sides tapered and backed by acoustical tissue with NRC value not less than0.60. |
| 56 | FINISHING |
| 57 | 12 mm cement plaster of mix ; 1:4 (1Cement : 4 Coarse sand) |
| 58 | 15 mm cement plaster on rough side of single or half brick wall of mix ; 1:4 (1Cement : 4 Coarse sand) |
| 59 | 20 mm cement plaster of mix ; 1:4 (1Cement : 4 Coarse sand) |
| 60 | Providing and applying white cement based putty of average thickness 1 mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete |
| 61 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour; Two coat |
| 62 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour; Two coat |
| 63 | ALUMINIUM WORK |
| 64 | Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/; appropriate Z sections and, other sections of approved make conforming to IS: 733 andIS : 1285, fixed with rawl plugs and screws of with fixing clips, or with expansion hold fasteners including necessary filling up Of gaps atjunctions, -at top, bottom and sides with required EPDM rubber/ Neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including clea angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steelscrews, all complete as per architectural drawings and the directions of .Engineer-in charge'. (Glazing and panelling to be paid-for separately): For fixed portion; Powder coated aluminium (minimum;thickness of kg powder coating 50 micron) |
| 65 | For shutters of doors, windows & ventilators including providing and fixing hinges/pivbts and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately); Powder coated aluminium (minimum thickness of powder coating 50micron) |
| 66 | Providing and fixing glazing in aluminium door, vyindow, ventilator shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): |
| 67 | With float glass panes of 5.50 mm thickness |
| 68 | Toughened glass 12 mm thickness |
| 69 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete; Upto 5mm depth and 5 mm width |
| 70 | WATER PROOFING |
| 71 | Providing and laying water proofing treatment to vertical and horizontal surfacesof depressed portions of W.C., kitchen and the like consisting of : (i).1 st course of applying cement slurry @ 4.4 Kg/sqm mixed with waterproofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface, (ii) llndcourse of 20mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed. with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) lllrd course ofapplying blown or residual bitumen applied hot at 1.7 Kg. per sqm of area:(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be TOO mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) |
| 72 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a).First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours.(b).Second layer of slurry .of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm.This layer will be allowed to air cure for 4 hours followed with water curing for. 48hours.The rate includes preparation of surface/ treatment and sealing of all joints,corners, junctions of pipes and masonry with polymer mixed slurry |
| 73 | Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown bitumen. 85/25 or 90/15 conforming to IS: 702 applied hot @ 1.45 Kg per square metre of area for each course, second course of roofing felt type 3 grade-l (Hessian based self finished bitumen\\" felt) and fourth and final course of stone grit 6mm and down size or pea-sized gravel spread at 6 cubic diameter per square metre including preparation of surface but excluding grading complete with; Bitumen felt (Hessianbase) type 3 grade I conforming to IS: 1322, |
| 74 | PILE WORK |
| 75 | Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below , the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of i boring with bentonite solution and temporary casing of appropriate : length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including I removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap). Note Truck Mounted rotary/TMR/Tubewell boring machine shall not be used; 500 mm dia piles |
| 76 | PAVER BLOCK FOR PARKING & VEHICLE RAMP |
| 77 | Providing and laying factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand,filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 60 mm thick |
| 78 | Laying two layers of 10 mm & 40 mm stone & 100 mm thick including supply of stones and preparing surface complete. |
| 79 | DISMANTLING AND DEMOLISHING |
| 80 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 81 | Vertical load testing (initial) of piles in accordance with IS : 2911 (Part-IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification and up to 50 tonne capacity pile |
| 82 | SANITARY INSTALLATIONS |
| 83 | Providing and fixing white vitreous, china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.l. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid. |
| 84 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls andfloors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580 x 440 mm with integral type foot rests |
| 85 | Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe. |
| 86 | Providing and fixing white vitreous china flat back or wall corner type .lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with utomatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.l clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors whereverrequired: One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 87 | Providing and fixing 600x450 mm beveled edge mirror of superior glass of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 88 | Providing and fixing toilet paper, holder: C.P. brass |
| 89 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) Pipes, havingthermal stability for hot & cold water supply, including all CPVC plain& brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings wjth one Step CPVCsolvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in harge.Concealed work, including cutting chases and making good the wall etc. |
| 91 | 25 mm nominal dia Pipes |
| 92 | 32 mm nominal dia Pipes |
| 93 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water upply, including all CPVC plain s brass threaded fittings, including fixing the pipe with clamps ,at 1.00 mspacing. This .includes jointing of pipes & fittings with one step CPVC, solvent cement and testing of joints complete as per direction of Engineerin Charge Internal works exposed on walls; 40 mm nominal dia Pipes |
| 94 | Providing and fixing brass bib cock of approved quality17.8.1. 15 mm nominal bore |
| 95 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 > 17.28.1. 15 mm nominal bore |
| 96 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter |
| 97 | Providing, and fixing brass stop cock of approved quality17.9.1. 15 mm nominal bore |
| 98 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of: approved quality and colour. 25mm nominal bore, weighing not less than 62 gms |
| 99 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. bra§s waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 100 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with G.l. brackets and stainless steel plug 40 mm, including painting of fittings .and brackets; cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm |
| 101 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:25 mm nominal bore |
| 102 | Providing and fixing 8 mm dia C.B / S.'S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 103 | PVC PIPES,BENDS,JUNCTIONS,TEES ETC.Supplying, fitting and fixing PVC pipes of 6 Kg/cm2(Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. External Drainage a) In exposed surfaces or in trenches.(i) 110mm dia. |
| 104 | (iii) 75mm dia. |
| 105 | Supplying, laying, jointing, testing and comissioning of approved make PVC floor trap with C P grating with required concrete encasing all around, complete.a) 110 x 75 mm dia (20 mm water seal) |
| 106 | Providing & Fixing in position Domestic Water storage Tank 12x1500 ltr capacity. 4 Layer Tank of Approved Make, with cover and suitable locking arrangement including 50 mm dia. Pvc pipe |
| 107 | Providing and Instaling (Fibre-reinforced plastic) FRP Sewage Tanks having multiple chambers and instalation as per NBC guideleines. Storage Capacity: 2000 Ltr |
| 108 | Providing and Instaling Water Filter System of capacity 600 LPH |
| 109 | Providing & Fixing in position HDPE wheeled plastic dustbin of capacity 1100 ltr |
| 110 | IEI WORKS |
| 111 | Wiring for light point/fan point / exhaust fan point/call bell point with 1.5mm2 FR PVC insulated copper cond. S/C cable in PVC casing capping with modular type switch, modular plate suitable size M.S box and earthing the point with 1.5mm2 FR PVC insulated copper, cond. S/C cable etc. as reqd. |
| 112 | 1. Gorup A |
| 113 | 2. Group B |
| 114 | 3. Group C |
| 115 | Wiring for light point/power plug with 2x4mm2 FR PVC insulated copper conductor single core cable in PVC casing capping along with 1 no. 4mm2 FR PVC insulated copper conductor single core cable for loop earthing etc. as required |
| 116 | Wiring for circuit/sub-main wiring along with earth wire with (the following sizes of) PVC casing capping insulated copper conductor single core cable in in etc. as reqd. |
| 117 | 1. 2x1.5mm2+1x1.5mm2 earth wire. |
| 118 | 2. 2x2.5mm2 +1x2.5mm2 earth wire. |
| 119 | 3. 2 x 4mm2 + 1 x 4mm2 earth wire. |
| 120 | 4. 2 x 6mm2 + 1 x 6mm2 earth wire. |
| 121 | 5. 2 x 10mm2 + 1 x 10mm2 earth wire. |
| 122 | S/F (following modular type switch/socket) on the existing switch switch box/cover i/c connection etc. as reqd. |
| 123 | 1. 15/16 amps switch. |
| 124 | 2. 15/16 amps socket outlet. |
| 125 | 3. 5/6 amps switch. |
| 126 | 4. 5/6 amps socket outlet. |
| 127 | 5. Modular Blanking Plate |
| 128 | S/F (following size/ modules) G.I. Box along with modular base and cover plate for modular switch in recess as reqd. |
| 129 | 1. 1 or 2 module (75mmX 75mm) |
| 130 | 2. 4 module (125mmX 75mm) |
| 131 | 3.6 module (200mm X 75mm) |
| 132 | 4. 8 module (125mmX 125mm) |
| 133 | 5. 12 module (200mmX 150mm) |
| 134 | Fixtures |
| 135 | S/F 100 W LED Energy saving,aluminium IP66 facade light. |
| 136 | S/F Recess mounting LED down lightetrs BGSL 0101WH,220223 cast aliminium housing, fixed with collimated lens, 1x1w white LED mounted on MCPCB, extreded AL. Heat sin spring loaded mounting clips complete with connection etc as reqd |
| 137 | S/F of IP 66 10W LED Bollard. |
| 138 | S/F 45 W LED post top lamp on existing pole. |
| 139 | S/F 3M decorative hot dipped galvanised mild steel step pole with grey powder finish. |
| 140 | S/F EROS DECORATIVE ARMS for decorative pole. |
| 141 | S/F 48\\" sweep (1200mm) A.C. ceiling fan complete with down rod, cannopy, 3(three) blades but without regulator etc. as reqd. (Make Bajaj/Usha or similar). |
| 142 | S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc. as reqd. |
| 143 | S/F 305mm sweep exhaust fan complete with all accessories i/c connection etc. |
| 144 | S/F 15ltr water geyser A.C 2KW vertical type with all accessories (150557 SKT-PLUS 151) i/c connection etc as reqd. |
| 145 | S/F decorative/fancy type bracket luminaries double with 11W CFL lamp complete with accessories and including connection etc as reqd. |
| 146 | S/F Indo voltage corrector Automatic /Stabilizer,5KVA(140-280V) for Air conditioner. |
| 147 | S/F 2 tone capacity split type Air conditioner(Diamond 3 star 5G30) complete without voltage stabilizer, |
| 148 | Earthing and Switchgears |
| 149 | Earthing with copper earth plate 600mm x 600mm x 6mm thick i/c accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd. |
| 150 | Extra for using salt and charcoal for G.I. or copper plate earth electrode as reqd. |
| 151 | P/F 8SWG dia GI copper wire on surface or in recessed for loop earthing along with existing surface/recessed conduit/sub-main wiring/cable as reqd. |
| 152 | Supply of PVC sleeve |
| 153 | S/F of Bus bar Chamber with 4 strips copper bus bar of length 300mm suitable for 200 Amp capacity complete with all accessories i/c connection earthing the body etc as reqd. |
| 154 | S/F (2+8) say single door/double door and neutral, sheet steel, MCB distributon board, 240 volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar, hinge front acrylic cover for the MCB knobs detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required. |
| 155 | S/F 5 amp. to 32 amp. Rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc. as reqd. |
| 156 | S/F 63amp double pole 240V isolator in the existing MCB DB complete with connection, testing and commissions etc. as reqd. |
| 157 | 16 Sqmm ISI mared PVC insulated AL cable |
| 158 | Washers |
| 159 | Iron screws, 45 x 6 mm |
| 160 | Brass nipple |
| 161 | Supply 25 mm dia ISI Marked, PVC Conduit. |
| 162 | Washers |
| 163 | Fabrication of control panel board by 16 gauge steel sheet, along with componets, mounting, making, strip wiring auxillary components mounting making strip wiring auxillary components, wiring all over the panel i/c fixing charge, paimting etc as reqd. |
| 164 | Indicating Lamp |
| 165 | Voltmeter rage 0-500 v |
| 166 | Ammetre rage 0-200 A |
| 167 | Current transformer coil range 0-200 amp. |
| 168 | Hinges for Panel Door. |
| 169 | Panel door locks |
| 170 | Selector switch for ammetre & voltmetre |
| 171 | Panel intrenal power wiring by 40 X 6mm copper strip |
| 172 | P/F following rating and breaking capacity MCCB in the existing cubicle panel board including drilling holes in cubicle panel nad making connection as reqd |
| 173 | 1. 4 pole MCCB 315 Amp 35KA |
| 174 | 2. 4 more MCCB 100 Amp 16KA |
| 175 | 3. 4 more MCCB 160 Amp 25 KA |
| 176 | S/F 63 Amp 4 pole 230V moulded vcase circuit breakers MCCB ac 415 V having a sensitive current up to 300MA in the4 existing MCB BD complete with connection testing and commissioning etc as reqd. |
| 177 | P/F 400 amp TPN stand ground on load change over Switch (compact design) 415 /500V including connection etc as reqd |
| 178 | Lightining Conductor |
| 179 | P/F of lightining conductor finial made of 25 mm dia 300m long copper tube having prong at top with 85mm dia 3mmm thick copper plate i/c holes etc as reqd |
| 180 | Supply of PVC Sleeve |
| 181 | Slay clamp |
| 182 | Supply 25 mm dia ISI Marked, PVC Conduit. |
| 183 | Fire fighting, As per CPWD PAR 2025, With wet riser system |
| 184 | Fire Alarm System, As per CPWD PAR 2025, Manual Fire Alarm System |
| 185 | UnderGound sump, As per PAE (5.5) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 03, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 13, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 8 daysNov 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender