Tender For Rajkiya Higher Secondary School, Silhat Rudrapur
Tender Value
33.94 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
5 days left
EMD
68000
Bank guarantee accepted
Document Fee
2354
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Deoria → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Rajkiya Higher Secondary School, Silhat Rudrapur
BOQ
| Sl. No. | Item Description |
| 1 | Removing dry or oil bound distemper, waterproofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. As per D.S.R-13.91 |
| 2 | Removing dry or oil bound distemper, waterproofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. As per D.S.R-13.91 |
| 3 | Supply of Muraga jali 1/2x 24 gauge. |
| 4 | Grading roof for water proofing treatment with Cement concrete 1:2:4 (1cement:2coarsesand:4graded stone aggregate 20 mm nominal size)22.14.1 |
| 5 | 12 mm thick plaster in 1:3 in cement and fine sand and finish with neat cement finishing on the top of Roof As per D.S.R 13.7.1 |
| 6 | 12 mm cement plaster of mix: 1:6 (1 cement:6 coarse sand) e.t.c As per D.S.R items No-13.4.2 |
| 7 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6mm for diagonal braces and central cross piece as pr dsr 10.5.2 |
| 8 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (PartI) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butthinges with necessary screws. Single leaf.-D.S.R.-9.21.1 |
| 9 | Providing and fixing lSl marked oxidisedl vl.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised asp er Ls 1378). 300x16 mm (D.S.R.-9.62.1) |
| 10 | Providing and fifing lSl marked oxidised M.S.tower bolt black finish, (Barrel type) with necessary screws etc. complete(Copper oxidised as per lS 1378).250x10 mm (D.S.R.-9.63.1) |
| 11 | Providing and fixing lSl marked oxidised M.S. handls conforming to lS:4992 with necessary screws etc. complete (Copper oxidised as perts 1378)(D.S.R. -9.66.1) |
| 12 | Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works as per dsr10.25.2 |
| 13 | Demolishing cement concrete manually /by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix As per D.S.R-) 15.2.2 |
| 14 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 (25 mm thick) |
| 15 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete |
| 16 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete |
| 17 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement as pr dsr 8.31 |
| 18 | Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. - D.S.R.-13.80 |
| 19 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture: (M.S.works and wood work).(D.S.R.-13.62.1) |
| 20 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification. Two or more coats on new work(Inner walls & Ceiling)(DSR-13.41.1) |
| 21 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work( Two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20kg/10 sqm) (Outer surface).Ground Floor-D.S.R.-13.47.1 |
| 22 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with sealring conforming to IS:5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter [DSR-12.41.2] |
| 23 | Providing and fixing on wall face unplasticised-PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with sealring conforming to IS:5382, leaving 10mm gap for thermal expansion.110 mm bend [DSR-12.42.5.2] |
| 24 | Providing and fixing unplasticised- PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. scrwes of required length, including cutting brick work and fixingin cement mortar 1:4 (1cement:4coarse sand) and making good the wall etc. complete.110 mm[DSR-12.43.2] |
| 25 | Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 26 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern As per D.S.R-17.4.1 |
| 27 | White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps As per D.S.R 17.7.1 |
| 28 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. |
| 29 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe withclamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.15 mm nominal outer dia Pipes 18.7.1 |
| 30 | 20 mm nominal outer dia Pipes 18.7.2 |
| 31 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support fortank. |
| 32 | Providing & fixing CP brassbib cock of approved quality conforming to IS 8931 15mm nominal bore 18.49.1 |
| 33 | Supply and fixing of inguration post at site |
| 34 | Wiring For light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 1.1 Group C1.10.3 |
| 35 | Wiring for circuit/ sub-main wiring along with earth wire with the following size of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduitas required.1.14 2X1.5 sqmm + 1x1.5 sqmm earth wire1.14.1 |
| 36 | 2X2.5 sqmm + 1x 2.5 sqmm earth wire 1.14.2 |
| 37 | Supplying and fixing following size / modules , GI box along with modular base & cover plate for modular switches in recess etc as required.1.27 1 or 2 module(75mm X 75 mm ) 1.27.1 |
| 38 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch , connection etc. as required. 1.31 |
| 39 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box / woodedn block including connection etc. as required. 1.33 |
| 40 | Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required. 1.50 upto 450 mm sweep.1.50.1 |
| 41 | supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as |
| 42 | Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminiumalloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase ACsupply Ceiling Fan compliant to IS 374:2019 fan i/ external connections with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable and earthing etc. as required 900mm, service value ≥ 5.1 CM/Min/Watt, air delivery 130 CM/Min (Minimum) 9.1.1 |
| 43 | Supply & fixing of IP 20, Front Lit, Mid Power SMD type LED Light, recess / Surface mounting round 10 Watt to 15 Watt, Cut out Min. 125 mm, Height Min 40 mm, Led Down Lighter having Power coated die cast aluminium housing with heat sing, High purit/transmisivity UV Stabilized Non yellowsid diffuser / Refelctor for uniform light distribution, detachable driver set, suitable for 24 Hr Continuous Operation, complete in all respects. 23.02 1200-1800 system lumens,>120 Lm/W, PF>0.95, THD<10% at full load, CRI>80, >300 V over voltage protection, 2.5 KV internal Surge Protection, with 5 years warrantee.23.02 CAT-AAA |
| 44 | Supply and fixing of LED Tube Light with heavy Duty Metal Boxt ype Tube Light Fitting 1x22 watt suitable for upto 1x22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended completein all respect. 2620 system lumens, with fully covered diffuser type>120 lm/w PF>.95, THD<10%, CRI>80, sheet thickness min 0.8 mm, Tube with aluminium heat sink ,>300 V over voltage protection, 2.5 KV internal Surge protection, with 5 years Warrantee. 23.07 CAT. - AAA Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender