Tender For Provn Of Washing Platform With Covered Shed For Tanks At Corps Zonal Wksp In Army Area Under Ge (A) No 1 Jodhpur .14/Lbw/Jodh/2024-25
Tender Value
42.17 Lakhs
Estimated cost
Bid Submission
11 Nov 2026
1 days left
EMD
84340
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jodhpur → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Washing Platform With Covered Shed For Tanks At Corps Zonal Wksp In Army Area Under Ge (A) No 1 Jodhpur .14/Lbw/Jodh/2024-25
BOQ
| Sl. No. | Item Description |
| 1 | Surface dressing not exceeding 15 cm deep getting out in soft/loose type of soil etc. complete all as specified and directed. |
| 2 | Excavating over areas, not exceeding 1.5 m deep and getting out in soft/loose soil,complete all as specified and directed. |
| 3 | Excavating over areas, exceeding 1.5 mtr but but not exceeding 3.00 mtr deep and getting out in soft/loose soil,complete all as specified and directed. |
| 4 | Returning, filling in excavated soil, including spreading, leveling, watering and well ramming in layers of not exceeding 25 cm thick after the cables & pipes etc. are laid, jointed & tested and foundations complete all as specified and directed by Engineer-in-Charge. |
| 5 | Removal of surplus excavated soil to a distance exceeding 50 Mtr and depositing where directed by Engineer-in-Charge at a level not exceeding 1.5 m above the starting point complete all as specified. |
| 6 | M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate), as in sub base of floor, mass concrete in foundation and path etc including. compaction properly & universal and laid to level, complete all as specified and directed. |
| 7 | M&L for quarried rubble stone or broken nullah boulders, in large pieces for soling/subbase of road, etc.complete all as specified and directed. |
| 8 | M&L reinforced cement concrete M-25 (design mix) (using 20 mm graded crushed stone aggregate) as in foundation including including rafts,footing,foundation beams; plinths beams; rafts for columns, etc.; basement slabs, under-reamed piles and mass concrete etc.complete all as specified and directed. Note : Reinforcement & form work will be measured & paid seperately under respective item of BOQ. |
| 9 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc.,rough finish surface of concrete complete all as specified and directed. |
| 10 | M&L for mild steel TMT steel bars 10mm dia and over grade Fe-500D, cut to length, bent to shape required, including cranking bending spirally for hooping for column,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed. |
| 11 | M&L for mild steel TMT bars 8 mm dia and over upto and including 10mm dia. grade Fe -500D , as in stirrups, spacers & binders ,cut to length, bent to shape required, including cranking bending spirally for hooping for coloumn,, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete etc all as specified and directed. |
| 12 | S&F for joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) Fe 410-W (Gde-E-250) quality-A complete all as specified and directed. |
| 13 | M&L for plates (plain or chequered) channels, square cut or notched with riveted, bolted or welded attachment conforming to Fe 410-W( Gde-E-250) quality -A complete all as specified and directed. |
| 14 | M&L for tie bars with screwed ends, nuts, washers and mild steel plates for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 15 | S&F of pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. |
| 16 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa & minimum AZ @150 gm/Sqm( be coated with hot dip alloy of 55 % aluminium, 43.5% Zinc, 1.5% Silicon and finished with resin coat on both surface @ 150 gm/Sqm of coating both surfaces) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified & directed. |
| 17 | M&L for prepartion of new or previously untreated steel surface of any description , not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surface complete all as specified & directed. |
| 18 | M&L for roof trusses (framed) trussed purlins, crane gantnes, rails and fastenings and heavy bracket framing (Beam tee, angle, channel or flat sections) inclduing distance pieces, cleats etc conforming to Fe-410-W (Gde E-250) quality-A complete all as specified & directed. |
| 19 | M&L for squared rubble walling, Jodhpur type, regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6, complete all as specified and directed. |
| 20 | M&L 15 mm thick cement plaster in CM 1:4 other than fair surfaces or over stone masonary surface, faces finished the surfaces even & smooth without using extra cement complete all as specified and directed. |
| 21 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation,trenches,or drain etc not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in all kind/any type of soil,by mechnical means(hydraulic excavator) etc, complete all as specified and directed. |
| 22 | Extra over stone walling for hammer dressing to face stone & dressing of face beds & joints as specified of squared rubble walling Jodhpur type brought upto courses with maximum depression of face from straight edge held against the dressed surface not exc 20mm and dressing face beds and joints, complete all as specified and directed. |
| 23 | M&L for junction box hot press moulded SMC of outside suitable dimension with locking arrangements consisting of necessary suitable arrangements for incoming & out going cables with cable glands & having aluminium bus bar of 32 amps capacity for SPN on necessary base plate and porcelain base including necessary flat iron for clamps with nuts, bolts & washers etc complete all as specified and directed. |
| 24 | S&F connecting, and commissioning of Street light fitting 35 watt LED , IP-65 protection, single peice pressure dia cast aluminium alloy housing high grade powder coated finish with heat resistant toughned clear glass cover for lamp and contror gear compartment with high voltage surge protection device upto 4.5 KV, prewired including providing GI pipe bracket made out of 40 mm dia light grade GI pipe bend to shape as per site requirement not less than 1.60 m long to be fitted / fixed to on PCC/Steel tubular pole/ wall with & including nuts, bolts of 12 mm dia 100 mm long including washer, 40 x 6 mm size clamps-03 Nos etc and applying two coat of aluminium paint over a coat of primer on steel surface and conductor to fitting with 3 core 1.5 sqmm PVC insulated cable complete all as specified & directed. |
| 25 | Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp and conductor to fitting with 3 core 1.5 sqmm PVC insulated cable complete all as specified & directed. |
| 26 | M & L Sub main wiring with two runs of single core 2.50 Sqmm PVC insulated FRLSH multistanderd copper conductor cable and one run of 2.50 Sqmm PVC insulated unsheathed FRLSH multi stranded copper conductor cable for earth wire drawn in & including concealed rigid non metallic PVC conduit medium grade with fittings (ISI marked) not less than 20 mm dia/appropriate dia with accessories & fittings complete and making good disturbed surface wall complete all as specified and as directed. Note : - Two runs of 2.50 Sqmm cable and one run of earth wire 2.50 Sqmm & conduit shall be measured as one unit length and extra length of cable required for connection to MCBs shall be deemed to be include in unit rate quoted by bidder. |
| 27 | S & F sheet metal enclosures IP-43 (CRCA sheet) dust & vermin proof for DBs when MCBs to be used in single pole and neutral (SPN) double door 415Volts, 08 way, suitable IP protection with magnetic locking system including necessary provision for inserting the the DBs in wall & for one MCB SPN as incoming & six MCBS SP as out going 200 amp rated copper bus bar and neutral link (ISI marked) complete all as specified and as directed. |
| 28 | S&F miniature circuit breaker (MCB) of single pole & neutral (SPN) and current carrying capacity 32 Amp , 240V ,breaking capacity 10 KA, 'C' curve in the MCB DB complete with connection testing and commissioning including suitable size copper lugs with over load and short circuit protectionetc, complete all as specified and as directed |
| 29 | S&F miniature circuit breaker (MCB) of single pole (SP) and current carrying capacity 6 Amp to 32 Amp , 240V ,breaking capacity 10 KA, 'C' curve in the MCB DB complete with connection testing and commissioning including suitable size copper lugs with over load and short circuit protection etc, complete all as specified and as directed |
| 30 | Supply , fixing/installation,commissioning & testing of 5 HP high pressure motor pump 1200RPM with following Specifications:- 1. motor :- 5HP 50Hz (Three Phase) 2. Type :- High Pressure Triplex Plunger Direct Coupled Pump 3. Water flow Lpm :- 15 4. Maximum Pressure :- 150 BAR /2175PSI 5. Required Section pressure :- Flooded Section Max. up to 2 BAR 6. Plunger Diameter (mm) :- 18 7. Connection size :- Inlet 1/2\\" / outlet 3/8\\" (Both Female ) 8. Transmission :- Direct couple No required v belt or motor pulley 9. cylinder :- Stainless Steel, V- Belt Size: B-40 10. Plunger(Surface finish) :- High Finish ceramic(<.25 Ra) 11. Gland packing:- Durable Fiber impregnated Buna n seal 12. Crank Case:- High strength Aluminium Pressure Die Casting, 13. Standard accessories:- Spray Nozzle with adjustable spray nozzle, 15M water outlet high pressure hose, 10 metre electric cable, frame mounted, 10 meter suction pipe with strainer fitted including foot valve, snow foam bottle, wooden box frame for standing including all necessary accessories required for smooth functioning of motor as directed by Engr-in-Charge |
| 31 | Supply & fixing DOL starter for run 3 Phase 5 HP induction motor including all asseccories etc, complete all as specified and as directed |
| 32 | Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 6 Sqmm 4 core cable complete all as specified and directed. Note:- 1. Excavation & earthwork shall be measured & paid under respective item. (2) All Necessary T & P required shall be arranged by the Contractor. |
| 33 | Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 4 Sqmm 3 core cable complete all as specified and directed. Note:- 1. Excavation & earthwork shall be measured & paid under respective item. (2) All Necessary T & P required shall be arranged by the Contractor. |
| 34 | Supply, laying , jointing & testing LT under ground cable XLPE insulated, screened ,PVC bedded, galvanised steel strip or wire armoured, electric power cable ( heavy duty) with standard aluminium conductor , 1100 Volts grade of cross sectional area 25 Sqmm 4 core cable complete all as specified and directed. Note:- 1. Excavation & earthwork shall be measured & paid under respective item. (2) All Necessary T & P required shall be arranged by the Contractor. |
| 35 | Supply and spreading clean, dry, fine river sand for under ground electric cable in two layers (8cm thick before laying of cable & 15cm thick after laying cable to a total of 23cm) including gentle punning the sand upto 18cm (total thickness) and consolidated around cable for protection of UG cable complete all as specified and directed. NOTE:- For measurement purpose punned thickness shall be considered as per clause 19.75 of SSR Part-I. |
| 36 | Supplying & Laying factory made un-reinforced pre-cast flat concrete cable protection cover of class LV, type- 1, size 300 mm x 180mm x 40mm,and abutting each other with gap between adjacent precast concrete cable cover not exceeding 10 mm over underground cables for protection,complete all as specified and directed by the Engineer-in-Charge. |
| 37 | Supply and laying GI pipe 40 mm bore light grade with fitting for cable protection at under road crossing/ for protection of cables on poles complete all as specified and directed by the Engineer-in-Charge. |
| 38 | Supply, installing, commissioning and testing of LT distribution panel board factory made, cubical, out door type, powder coated with fabricated 3.15 mm thick skelton with angle iron / flat iron frame work , bus Bar chamber,front openable hinged door with locking arrangement and common openable hinged door from rear side,floor mouting type, IP-65 protection and as per IS, comprising the following accessories ,including connecting with the incoming / out going feeders by providing cable glands and cable lugs etc, complete all as specified and as directed:(a) INCOMING (i) Rectangular Copper strip of size 50x5mm fixed on insulated mounting arrangement-03 Nos. (ii) MCB TPN 40 Amps, breaking capacity 25 KA, - 1 No(iii) Ammeter digital type 0 to 100 A - 1 No(iv) Voltmeter digital type with selector switch 0-500 V - 1 No(v) Phase indicating light LED type - 1 set.(b) OUTGOING (i) MCB SP 240V ,breaking capacity 10 KA, 'C' curve - 3 Nos(ii) MCB 32 Amp ,SPN ,breaking capacity10 KA,\\"B\\" Series-01 No(iii) Free space for MCB SP Amp -5 Nos |
| 39 | Supply, installing, commissioning and testing 10 HP 20 CFM rotary screw Air compressor with Air tank capacity 500L three phase with class 1 air quality standard etc, complete all as specified and as directed with following technical specifications : Technical Specification:-(i) Compressor Type -Rotary Screw type compressor (ii) Motor type -10HP (7.5KW)(iii) Flow rate / capacity -20CFM to 40 CFM(iv) Air receive tank capacity capacity -500Ltr horizontal heavy duty steel tank with safety valve ,pressure gauge and manual /auto drain valve (v) Electric supply -3Ph (415 volt,50Hz AC)(vi) Cooling system -Air Cooled(vii) Working Pressure-8 to bar |
| 40 | M& Lfor Earthing complete with GI earth plate electrode 60cmX60cmX6mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to GI earth strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-3 of SSR Part-I (2009) connected to LT panel boards all as specified and directed including excavation and connected earth work in hard/dense soil, PCC 1:3:6 type C-1(using 20 mm graded crushed stone aggregate ) as in pit, 20mm dia GI pipe medium grade for watering pipe, 40 mm dia bore GI light grade as earth strip protection pipe, 50 mm thick pre-cast RCC 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate ) as in cover slab of size 300 mm x300 mm x 50mm as earth pit cover slab with & including 8 mm dia TMT bars @ 100 mm C/C both ways and with handle made out of 10 mm dia bars, funnel, strainer, charcoal and testing on completion includingdismantling/taking down of old unserveciable earthing complete all as specified and directed. Note- Unit rate quoted by bidder deemed to be included excavation and earth work in any type of soil with other arrangement complete all as directed. Note : Rate included for excavation & earth work in any type of strata as shown in electric plate no-3 in SSR Part-I. |
| 41 | Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed. |
| 42 | M & L for rendering 15mm thick on block masonary surfaces in cement mortar 1: 6 on internal faces of walls finished, even and smooth without using extra cement complete all as specified and as directed |
| 43 | M & L for Stone sett flooring with stone setts of size 200 to 250mm long,150 to 200mm wide and 150mm deep and sides dressed; bedded in cement mortar 1:3, joints 20mm thick; grouted in cement mortar 1:2 with an admixture of metallic floor hardner 5% by weight of cement and struck flush complete all as specified and as directed |
| 44 | M&L for Construction of Soakage well for 2.50 mtr dia( internal dia ) & 3.0 m (effective depth) including necessary excavation in earth work in any type of soil , plain cement concrete 1:3:6 type C-2 ( using 40 mm graded crushed stone aggregate ) as in foundation , RR masonary in cement mortar 1:4 in walls & honey masonary , reinforced cement concrete M-25 (design mix) as in slab cover including pre-cast cover slab having 8 mm dia TMT bar reinforced,plain cement concrete band and dwarf wall, form work to sides and soffits of RCC slab & filling with brick bats loose filling including interconnecting pipes of RCC /DWC complete all as specified and shown in drawing No. Tdrawaing no.CEJZ/TD/29 dt 14 Dec 2013 Sheet No. 1/3 complete all as specified. |
| 45 | M&L PCC 1:2:4 type B-2 (using 40mm graded crushed stone aggregate), as in sub base of floor, mass concrete in foundation and path etc including. compaction properly & universal and laid to level, complete all as specified and directed. |
| 46 | M&L for hard core of broken stone or boulder gauge not exceeding 63mm deposited, spread & leveled in layers not exceeding 15cm thick, watered and rammed to a true surface etc complete all as specified& directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 28, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender