Tender For special Repair To Bldg No. T-139 (Offr Temp Accn) Of 1843 Pnr Unit & Water Heaters, Refrigerators, Acs Against Ber At Mil Stn Dharchula And Provn Of 04 X Bathroom, 01 X Toilet, 02 X Urinal Point At Mil Stn Dharchula Under Ge (Mes) Pithorag
Tender Value
38.41 Lakhs
Estimated cost
Bid Submission
16 Nov 2026
6 days left
EMD
76900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pithoragarh → Uttarakhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No. T-139 (Offr Temp Accn) Of 1843 Pnr Unit & Water Heaters, Refrigerators, Acs Against Ber At Mil Stn Dharchula And Provn Of 04 X Bathroom, 01 X Toilet, 02 X Urinal Point At Mil Stn Dharchula Under Ge (Mes) Pithoragarh
BOQ
| Sl. No. | Item Description |
| 1 | DESCRIPTION OF ITEMS |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/disintegrated rocks complete all as specified and as directed. |
| 3 | Excavation over areas n.exc. 1.5m deep and getting out in hard dense soil including removal of excavated material n.exc 50m and depositing where directed at a level n.exc. 1.5m above the starting point |
| 4 | Demolition reinforced cement concrete in any description and in any position complete all as specified and directed. |
| 5 | M&L Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like using cement concrete type B-0 1:2:4 complete all as specified and directed |
| 6 | S&F Formwork to sides and soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surface of concrete complete all as specified and directed |
| 7 | Demolition of brick work, stone/boulder masonary built in cement mortar complete all specified and directed |
| 8 | Taking down cement plaster on brick or stone walls, of any description including raking out joints, hacking for key, scrubbing down with water, etc complete all as spfd and directed. |
| 9 | Returning filling including spreading, leveling, watering and well ramming in layers n exc. 25cm (hard/dense soil) |
| 10 | Removing excavated material (soils) n .exc 50 m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed. |
| 11 | M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed. |
| 12 | M&L for PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and directed. |
| 13 | M&L 50mm thick cement concrete type B-2, PCC 1:2:4 (20mm graded agg) as as directed |
| 14 | M & L for providing coloured chequered cement concrete tiles of size 30cm x 30cm x 20-25mm thick set & jointed in neat cement slurry with grey cement and pigment including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of chequered tile complete all as specified and directed. |
| 15 | M & L cement concrete 1:2:4 type B1 (20mm aggregate) in surface channel,coping,kerbs etc. complete all as specified and directed. |
| 16 | M&L for Precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate as in drain cover slabs, size required at site include necessary formwork complete all as specified and directed. |
| 17 | M&L RCC M-25 (Design Mix) as in foundation, including raft, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and as directed. |
| 18 | M&L RCC M-25 (Design Mix) as in columns, pillars, piers etc complete all as specified and as directed. |
| 19 | M&L RCC M-25 (Design Mix) as in beams, cantilever, lintels etc complete all as specified and as directed. |
| 20 | M&L RCC M-25 (Design Mix) as in slabs supported on walls, beams and columns etc complete all as specified and as directed. |
| 21 | M&L RCC M-25 (Design Mix) as in chajjas complete all as specified and as directed. |
| 22 | M&L form work to sides and soffits of roof beams, lintels lever shelves, chajjas incl supports over hang etc rough finished surfaces of concrete flat all as specified. |
| 23 | M&L form work to soffits of suspended slabs such as roof slab landings and similar works n exc 200mm thick (horizontal or slopping) for rough finished surfaces of concrete flat all as specified. |
| 24 | M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide |
| 25 | M&L form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams or similar works vertical or to batter for rough finished surface of concrete |
| 26 | M&L form work to sides of pillars, posts, struts, columns for rough finished surface of concrete |
| 27 | M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and binding with ms wire (annealed) not less than 0.9mm dia quality confirming to all as specified. |
| 28 | M & L mild steel TMT bars 6 to 8mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia all as specified and directed |
| 29 | M&L for brick work with sub class 'B' brick old size bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as spfd & directed. |
| 30 | M&L for Pre-cast cement concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar1:6, complete all as specified and directed. |
| 31 | M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as spfd & directed. |
| 32 | M & L Rendering 15mm thick in CM (1:6) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed. |
| 33 | M & L Rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement complete all as specified and directed. |
| 34 | M & L Rendering 5mm thick in CM (1:3) on fair faces of brick work or concrete surfaces as in ceiling to be finished even and smooth without using extra cement complete all as specified and directed. |
| 35 | M&L for hard core of broken stone or boulders gauge n.exc 63mm deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface of broken bricks aggregate, all as specified. |
| 36 | M&L cement concrete 100mm thick 1:4:8 of type B2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and as directed. |
| 37 | M&L PCC 40mm thick 1:2:4 of type B1 using 20mm graded stone aggregate as in sub base of floor complete all as specified and as directed. |
| 38 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed |
| 39 | M&L Granite (of any type) tiles 20 mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed in CM 1:6 etc complete all as specified and as directed |
| 40 | M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm, in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as spfd & directed |
| 41 | M&L for coloured glazed ceramic tiles in vertical surface, 450x350/300x600x7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick plaster in CM 1:4 complete all as spfd & directed. |
| 42 | M & L for 75mm thick PCC 1:3:6, type C-2, as in Plinth protection etc finished even & smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 meter and at change in direction complete all as specified & directed. |
| 43 | Taking down chowkhats or frame nexc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 44 | Taking down chowkhats or frame exc 1.5 sqm but nexc 4.00 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 45 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 100mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 46 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 47 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 48 | Factory made solid panel PVC wire mesh door shutter 30 mm thick (style) wood grain printed PVC sheet used instead of Plain colour PVC sheet & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90 degree) used instead of exposed portion of PVC sheet beading ,wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be secured with additional layer of wire netting 12mm gauge stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing |
| 49 | S&F for powder coated anodized aluminum frame for doors, windows ventilator with one or more rebates including joining cleat for fixing etc , screws, hinges, brackets, dash fasteners/ rawl plugs etc. complete all as specified and directed. complete all as specified and directed. |
| 50 | S&F powder coated Anodized aluminum window and ventilator shutters, without sash bars, aluminum sections weighing min. 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminum snap beading, screws, anodized aluminum fittings suitable handle (1no. per leaf), window lock (1no. per leaf) complete all as specified complete all as specified and directed. |
| 51 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 52 | S&F Anodized aluminum grill (anodized transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminum standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. |
| 53 | S&F 4.80 mm thick sheet glass ordinary quality and glazing with oil putty/rubber packing in square exc .50 sqm in each panels complete all as specified and directed. |
| 54 | S & F in repair Harrison rails/curtain rods, mild steel, chromium plated with brackets, stops, rollers etc fancy type as approved complete all as specified and directed. |
| 55 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed |
| 56 | S&F Factory made solid panel pvc door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and directed |
| 57 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete |
| 58 | S&F 3 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed. |
| 59 | S&F 100 mm Butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodized and fixed complete all as specified and directed |
| 60 | S&F 150 mm aluminium handles, cast type anodized complete all as specified and directed. |
| 61 | S&F150 mm aluminium anodized barrel tower bolts extruded section complete all as specified and directed |
| 62 | S&F 250mm long Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed |
| 63 | S&F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floors 150mm long all as specified and as directed. |
| 64 | S&F 250mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed |
| 65 | S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed |
| 66 | S&F in repair 15mm bore Chromium plated Bib taps fancy type, cast copper alloy screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified |
| 67 | S&F in repair 15mm bore Chromium plated cast copper alloy Two Way Bib Cock with Wall Flange complete all as specified and directed.(CAT part no. LYR-38041 of Jaquar or equivalent of other make) |
| 68 | S&F stop valve/angle valve, bore of dia 15mm of Chromium plated fancy type cast copper alloy screwed down for iron pipe and fixed etc complete all as specified and directed. |
| 69 | S&F 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed |
| 70 | S&F Tubular towel rail brass chromium plated 20mm dia, D type, 60cm long between flanges complete all as specified and directed |
| 71 | S&F in repair CP brass Towel stand fixed with and including Chromium plated brass screws and cleats complete all as specified and directed |
| 72 | S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brass bracket guard and railing 60cm long complete all as specified and directed. |
| 73 | S&F in repairs Brass CP mixer fancy type for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 74 | Supply and fix in repairs CP Wall Mixer with provision for Overhead Shower with 115mm Long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges for 15mm dia pipe complete all as specified and directed |
| 75 | S&F 600x450mm beveled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. |
| 76 | S&F PVC connections 15 mm size with PTMT nuts of length 600mm long Hot & Cold all as spfd and as directed. |
| 77 | S&F Brass chromium plated shower rose 125mm size incl shower arm 15mm dia complete all as spfd & directed |
| 78 | S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 79 | S&F in Grating doom chromium plated 100mm dia all as specified and directed |
| 80 | Cutting chases in brick wall, stone concrete block or slab walls, pining in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings ,steps, cills sunshades, shelves , lintels, etc and cutting chases for concealed water tubing and making good , cutting n'exc 10 cm girth complete all as specified and directed. |
| 81 | Cutting openings, through brick walls for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m |
| 82 | S&F 15 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc complete all as spfd & directed |
| 83 | S&F 20 mm bore GI tubing with all fittings medium grade fixed to wall or laid in floor etc complete all as spfd & directed |
| 84 | Cutting existing steel tubing 25mm dia, screwing for alterations or additions for fittings such as unions, gate valves etc complete all as specified. |
| 85 | Supplying & laying in trenches/wall Polyethylene (PE-AL-PE) composite pressure pipes (Inner dia 16mm) including all Crimp type internal sealing Plastic-Metal Composite fittings (such as elbows, tees, reducers, etc.) complete fixed to wall or laid in floor etc including taking up or down 15 mm GI tubing complete all as spfd & directed |
| 86 | S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 87 | S&F in repair Vitreous china premium/ 1st quality wash down water closet one piece EWC any color closed pattern incl all necessary accessories incl flushing cistern etc. complete in all respect all as specified. |
| 88 | S&F Vitreous China Wash Basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets , 32 mm PVC waste pipe, 32 mm CP Waste coupling and 15 mm dia Pillar taps fancy type chromium plated swan neck type complete all as specified and directed |
| 89 | S&F Vitreous China, semi-pedestal pattern (Anglo-Indian Type) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl connection to outgoing pipe and flushing pipe,P or S trap complete all as specified and directed. |
| 90 | S&F for PVC low level flushing cistern 10ltr capacity, with symphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc incl PVC connection 450mm long as spd and fixed all as specified and directed |
| 91 | S&F Vitreous China urinals, bowl type (back or corner wall type), complete including waste pipe, spreader providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; and all fittings |
| 92 | S&F in 32mm bore of trap Brass chromium plated bottle traps for wash basins/urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed |
| 93 | S&F Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed. |
| 94 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 95 | S&F PVC (SWR) floor trap with CP grating including jointing to waste pipe 75 mm bore outlet with solvent cement all as specified. |
| 96 | Demolition and breaking up drain pipes (Salt glazed ware, AC or reinforced concrete) set in cement mortar etc. complete all as specified and directed. |
| 97 | S&F PVC (SWR) bends 75 mm bore with or with out oval excess door complete all as specified and as directed |
| 98 | S&F 75mm bore PVC (SWR) junction single (Single T) equal or unequal with access door |
| 99 | S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed laid in trenches or in floors etc complete |
| 100 | S&F 110 mm bore PVC(SWR) Pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors/wall complete as all spfd and directed |
| 101 | S&F 110 mm bore PVC(SWR) bend/Tee any radius complete all as specified and directed. |
| 102 | S&F 110mm bore PVC (SWR) junction single (Single T) equal or unequal with access door |
| 103 | S&F Cowls (with 3 stays), riveted to and including 15 cm length of flue pipes, of 100 dia |
| 104 | M&L PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement. |
| 105 | Supply and fix 1000 Ltr rotational moulded polyethylene water storage tanks ( cylindrical ventricle with closed top) hoisted & fixed in position incl 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 106 | M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) unrolled and bonded completely to the substrate with side over lap of 75 mm & end over lap of 100 mm and then scaled/ fused by flame or bitumen including applying hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm over a coat of Bitumen primer @ 0.50 Ltr/Sqm complete all as specified |
| 107 | S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (beam, tee, angle channel or flat sections) (Fe-290 Gde E-165) including distance pieces, cleats etc. |
| 108 | Dismantling of plain or corrugated steel sheeting of any guage/thickness in roof covering/wall cladding complete all as spfd and directed |
| 109 | S&F 0.63 mm th Galvanized, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as spfd & directed |
| 110 | S&F 0.63 mm th Galvanized, corrugated mild steel sheeting (except Sheets) with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as spfd & directed |
| 111 | S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 112 | S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 113 | S&F reinforced concrete pipes, class NP3,150mm dla laid and jointed complete with collars, complete all as specified and directed. |
| 114 | M&L for concrete bed 1:4:8 type D-2 (Using 40 mm graded stone aggregate) as in drain pipes including packing under, and hunching against the side of pipes after the are laid and tested for 150 mm bore pipe, complete all as specified and directed. |
| 115 | S&F On site conventional LLDPE septic tank capacity of 3000 ltr designed to carry sewage and sullage water, incl excavation in any type of soil, 100mm PCC 1:4:8 below foundation, Vent shaft, connection etc., complete all as specified and directed. |
| 116 | Construction of Soakage well incl excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.20m dia and 3.0m effective depth all as per CEBZ TD/309 SHT-1/4 to 4/4 complete all as specified and directed |
| 117 | M&L for 18/19mm thickness Medium density fibre board,one side laminated other side balancing, exterior grade, fixed to framework/wall/hinges with screws etc |
| 118 | S&F Cabinet Hinges(Set of 2),Soft Close, Full Overlay 4 Hole, Nickel Plated for 14-20mm Thick shutter for wardrobe, kitchen, Bathroom etc complete all as specified and directed. |
| 119 | S&F catch magnet for cupboard shutter complete all as specified and directed. |
| 120 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets,fittings etc. as specified and directed. |
| 121 | S&F False Ceiling Horizontal level regular edge grid 600 x 600 mm form work using hot dip sections and fixing tiles vinyl laminated MPL gypsum panels size 595x595x6 to 8mm thick after lamination, Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs/roof truss by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified all as spfd and directed. |
| 122 | S&F 5 to 8mm thick PVC hollow type wall panelling any color fixed to wall/ceiling with L or U shaped beading at ends fixed with screws complete all as specified and as directed. |
| 123 | M&L for 6mm thick Plywood, grade BWR, type BB, fixed in ceiling and walling with screws to timber frame work complete all as sfd and directed. |
| 124 | Dismantling of timber scantling 40 sqcm and over in section in any position for unframed works complete all as specified and directed |
| 125 | S&F roof trusses (framed), trussed, purlins, crane gantries, rails and gastenings and heavy brackets framing (beam, tee, angle channel or flat sections) (Fe-290 Gde E-165) inicluding distance pieces, cleats etc. |
| 126 | Dismantling of timber scantling 40 Sqcm under in section in any position, fixed with nails unframed work complete all as spfd & directed. |
| 127 | M&L for II nd class hard wood plain fillets square or rectangular in section clean sawn secured with nails sectional area exc 13 sqcm and n.exc 25 sqcm complete all as specified and directed |
| 128 | M&L for one coat of creosote oil to wooden surfaces new or old of any description including preparation of surfaces complete all as specified and directed. |
| 129 | M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling complete. |
| 130 | M&L three coats of white wash on walls including preparation on new plastered surface and complete all as specified. |
| 131 | M&L for Preparing new plastered wall surfaces and applying two coat of oil emulsion distemper over a coat of wall putty 1mm thick over plastered surface to prepare the surface even and smooth complete all as specified and directed. |
| 132 | M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less that 50gm/liter and UV resistance as per IS-15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 liter / 10 Sqm over and including priming coat of exterior primer applied @0.90 liter/10 Sqm over new surfaces complete all as specified and directed. |
| 133 | M&L two coats of Cement base paint over a coat of primer including preparation of new plastered surfaces complete as as specified and directed. |
| 134 | M/L for two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm in width or girth incl preparation of new steel surfaces complete all as spfd and directed. |
| 135 | M & L preparing old previously treated surfaces of steel surface over 10 cm girth or width and applying Two coat of synthetic enamel paint complete all as specified and directed. |
| 136 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete incl fittings such as switches, ceiling roses, pendants, regulators, sockets etc and making good disturbed surfaces of walls, floors etc all as specified. |
| 137 | M&L point wiring with 1.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor FRLS cable in open/ surface/concealed PVC conduit of suitable size, complete with all accessories/fitting, including heavy duty PVC/ABS terminal switch board floor mounted/flush type (depth not less than 45 mm) of suitable size (lengthX width) for mounting modular switches, Modular sockets, Modular regulators including PVC module top cover plate with frame of suitable size , brass screw and washer including unsheathed single core PVC insulated cable green in colour 1.5 Sqmm multistranded copper conductor as contineous earth wire and connecting to earth dolly complete all as specified for one light point / fan point controlled by one way switch of 5/6 Amps. |
| 138 | All as per item No. 2 above but for one 3/5 pin socket outlet point on same board controlled by one way switch of 5 Amps. |
| 139 | All as per item No. 2 above but for one 3/5 pin socket outlet point on independent board controlled by one way switch of 5 Amps. |
| 140 | M&L point wiring with 2.5 Sqmm (Nominal cross sectional area) single core PVC insulated with PVC unsheathed multi stranded copper conductor FRLS cable in open/ surface/concealed PVC conduit of suitable size, complete with all accessories/fitting, including heavy duty PVC/ABS terminal switch board surface mounted/flush type to wall (depth not less than 45 mm) of suitable size (lengthX width) for mounting modular switches, Modular sockets, Modular regulators including PVC module top cover plate with frame of suitable size , brass screw and washer including unsheathed single core PVC insulated cable green in colour 2.5 Sqmm multistranded copper conductor as contineous earth wire and connecting to earth dolly complete all as specified for 15/16 amp socket outlet point controlled by one , one way switch of 15/16 Amps complete all as specified. |
| 141 | S&F Modular switch 1 module single pole one way 6 Amps, 240 volt complete all as specified. |
| 142 | S&F Modular switch 1 module single pole one way 16 Amps, 240 volt complete all as specified. |
| 143 | S&F Modular socket outletn, 2 module, 3 pin 5/6 Amps, 240 volt complete all as specified. |
| 144 | S&F Modular socket out let, 2 module, two in one 3 pin 5/6 Amps and 3 pin 15/16 amp , 240 volt, complete all as specified. |
| 145 | S&F ceiling rose, surface bakelite, AC, 60x30mm, 3 terminals complete all as specified. |
| 146 | S&F stepped type electronic fan regulator modular type ,2 module,240 volt complete all as specified. |
| 147 | S&F in replacement LED tube light warm white 4' long along with all fixtures and fittings, internally pre wired and including connecting up to ceiling rose with twin core twisted flexible copper conductor cable with suitable size, 20W complete all as specified. |
| 148 | Supply and fixing LED lights fitting mirror type with high out put diffuser with golden finidh 2 feet,1x 10/12 W, 220V, AC decorative type with driver, connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified. |
| 149 | S&F LED Bulb/LED retrofit 'T' bulb 12 watts, B22 end cap complete all as specified. |
| 150 | S&F in replacement LED bldg security lights of 35 Watt having pressure die cast aluminium housing with system lumens efficacy≥100 lumen/W, IP65 protection, IK07 rating, inbuilt electronic driver with PF>0.95 and mounting on GI bracket incl connecting up with three core twisted flexible copper conductor cable complete all as specified and directed |
| 151 | Supply and fixing in replacement security light bracket made out of light grade 25 to 32mm dia GI pipe of length 0.9 mtr bend to shape and mounting on wall using clamps nut bolts etc complete all as specified and directed. |
| 152 | Supply and fixing in replacment Decorative, wall mounting, brushed nickel finish fixture with Opal Glass diffuser suitable with 9 W LED lamp B22 base all as specified and directed. |
| 153 | Sypply and fix UP and Down Full -K telescope wall light 10 watt all as speciified and directed. |
| 154 | Supply and fixing LED luminaire 600 mm x 600 mm panel, 36 watt, 220 V AC recessed type with high efficiency PC diffuser soft glare free bright white/warm white light complete with driver, suitable for roof ceiling including connecting up with cord flexible copper conductor cable of suitable size complete all as specified. |
| 155 | Supply and fixing LED luminaire 230X230 mm panel (square/Round shape), 20/22 watt, 220 V AC recessed type with high efficiency PC diffuser soft glare free bright white/warm white light complete with driver, suitable for roof ceiling including connecting up with cord flexible copper conductor cable of suitable size complete all as specified. |
| 156 | Supply and fix 3W Flexible Wall Reading Lights with On Off Switch ,Gooseneck Light - 360° Lighting for bed side complete all as specified and directed. |
| 157 | S&F in replacement Energy saving, surface mounted, bulk head LED luminaire 10/12 W with Polycarbonate housing and diffuser complete including connecting up with cordflexible copper conductor cable of suitable size complete all as specified an directed. |
| 158 | S&F sheet metal enclosure for DB TPN 4 way with 200 Amp rated bus bar 240 Volts, Double door suitable for housing MCBs and isolators complete all as specified and directed |
| 159 | S&F in replacement MCB 4 pole 63 Amps, 240volts, 10KA, C Curve complete all as specified and directed. |
| 160 | Supply and fixing miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amp, 240V, 10 KA 'B' curve type, in the MCB DB complete with connection testing and commissioning complete all as specified. |
| 161 | Supply & fixing in repair industrial type SPN enclosure with a two pin and earth plug and socket including industrial plug 3 pin 20 Amp, complete with and including 20 Amps MCB, single pole, AC, 240 volts and flush to wall including all cuttings & chases etc on wall of fixed on surface of wall and making good including two coats of white / colour washing / distempering etc to match the existing disturbed surfaces complete all as directed . |
| 162 | Material and labour for sub main wiring with 2x4 Sqmm nominal cross sectional area (two single core cable of 4 Sqmm for Phase and neutral + o1 single core cable of 4.0 Sqmm for earth wire), 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 4.0 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed /surface conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dully including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing and taking down the old unserviceable submain wiring of ant type complete all as specified & directed.( Note - One meter of conduit along with 2x4.0 Sqmm wire and one 4.0 sqmm earth wire shall be measured as one length). |
| 163 | M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3 mm thick, buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level, conneted to galvanised earth wire 4.0 mm dia by means of bolts, nuts, cheek nuts and washers of galvanised or iron protected by 15 mm bore GI pipe (medium grade) and connected to main switch board as directed including concrete pit in PCC (1:3:6) type C1 precast RCC (1:2:4) type B1 cover slab 40x40 Cm x 6Cm reinforced with 8 mm dia deformed bar @ 5 cm c/c with one handle for lifitting made out of 8 mm dia MS bar, funnle, wire mesh, 20 mm bore GI pipe (medium grade) for watering including charcoal and salt in alternative layers necessary excavation and earth work in any type of soil and testing complete all as shown on electrical plate No-3 of SSR part-I, 2009. |
| 164 | Taking down exhaust fan of any size from existing position, dismantling, overhauling and cleaning throughly, oiling/greasing and re- assemble after replacing unsv parts etc and rehanging the same duly connected with new PVC three core flexible copper conductor cable of size 23/.0076, complete testing & specified. Note: Spare parts will be measured and paid separately under respective items as supply only as mentioned below. |
| 165 | M&L for taking out burnt copper winding from exhaust fan of any size/type and rewinding with existing /same guage of super enammeled copper wire complete all as specified. |
| 166 | Disconnecting electrically, taking down ceiling fan from existing position, dismantling blades, servicing by cleaning oiling /greasing, replacing unsv parts, split pins, check nuts, rubber seal etc, reassembling and rehanging at same or new locations duly connected with new cordflexible copper conductor cable of size 23/.0076 from ceiling rose and testing complete all as specified & directed.Note: Spare parts other than specified will be measured and paid separately under respective items. |
| 167 | Rewinding of AC ceiling fan motor 1200/1400 mm sweep any make with super enamelled copper winding wire of 35SWG gauge, sleeve work, varnishing with `B' class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block including cutting and taking out old burnt Al/Cu winding wire complete all as specified and directed. Note : (i) Rewinding should be done at workshop |
| 168 | Supply only for fixing Ball bearing of suitable size/No for Ceiling fan of size 1200/1400mm sweep complete all as specified and directed. |
| 169 | Supply only for fixing capacitor 2.5 mfd±5%, 440 Volt, AC, 50/60Hz incl PVC clamp complete and all as specified. |
| 170 | Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 4 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed. |
| 171 | Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 M depth in soft / loose soil and geting out complete all as specified and directed. |
| 172 | Material and labour for sand cushioning with dry fine sand including filling, spreading, levelling in layers in cable trench with approved quality of sand for protection of under ground cable complete all as specified and directed. |
| 173 | Material and labour for contineous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified and directed. |
| 174 | Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in 25mm thick layer complete all as specified and as specified. |
| 175 | Removal of surplus excavated soil to a distance exc50 m but not exc in 100 m and deposited wher directedat a leveln exc 50 m above the starting point complete all as specified. |
| 176 | Supply / laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed. |
| 177 | Disconnecting, dismantling and taking down carefully geyser of size 25 to 50 ltrs capacity from wall after unscrewing nuts/bolts etc for repairing and replacement of unsv spare parts such as NRV, safety valve, pressure release vlave incl descaling of rust and rubbish material from the inner tank and reassembling, refixing in same position with suitable size gutties/anchot bolts and nuts incl testing complete all as specified and directed. Note:- 1.Spare parts/ items other than specified will be measured and paid separately under respective items. |
| 178 | Supply only thermostat as per sample for geyser of capacity upto 50Ltrs with temperature range adjustable from 25 to 75 degree centigrade, 220 Volts AC supply complete all as specified and directed. |
| 179 | Supply only heating element ISI Marked of rating 2.0 KW of size and type as per site requirement incl rubber washers suitable for water heater storage oc capacity upto 50Ltrs complete all as specified . |
| 180 | Supply and fix changeover single phase , making all the connection all as specified and direcrted. |
| 181 | Suppply and fix power unit ( 16 amp socket with 20 Amp MCB incl 16 Amp Plug) all as specified and directed. |
| 182 | Suppply and fix USB Charger type A and C all as specified and directed. |
| 183 | Supply & fixing modular Bell Push 6A,(1 or 2 module as per site requirement), 240 volts complete all as specified & directed. |
| 184 | S&F in replacemnt of Bell ding dong type complete all as specified and directed. |
| 185 | Supply install and testing water heater storage type (Geyser) single phase 230V , 50m HZ , 5 star energy saving high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion , vertical insulation type 25 liter Cap 2000 watt rated power , incoloy 800 glass coated heating element , inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates , rated pressure 0.8 MPa, IPX4 protection consist of safety valve , thermal cut off , thermostat including connecting up and fixing arrangement on wall including proving hole fastners-04 nos hot and cold water metallic flexible pipe 15 mm bore of adequate length as provided by OEM or required at site -02 Nos , non return valve-01 nos and including necessary plumbing work, complete with integrated shock safe plug with all protection features as per OEM design and standard all as specified and directed. Note - QR code made of vinyl with UV laminate must be pasted on each geyser which will indicate CA No, Job No and name of contactor . |
| 186 | Supply install and testing water heater storage type (Geyser) single phase 230V , 50m HZ , 5 star energy saving high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion , vertical insulation type 50 liter Cap 2000 watt rated power , incoloy 800 glass coated heating element , inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates , rated pressure 0.8 MPa, IPX4 protection consist of safety valve , thermal cut off , thermostat including connecting up and fixing arrangement on wall including proving hole fastners-04 nos hot and cold water metallic flexible pipe 15 mm bore of adequate length as provided by OEM or required at site -02 Nos , non return valve-01 nos and including necessary plumbing work, complete with integrated shock safe plug with all protection features as per OEM design and standard all as specified and directed. Note - QR code made of vinyl with UV laminate must be pasted on each geyser which will indicate CA No, Job No and name of contactor . Please Enable Macros to View BoQ information |
| 187 | Supply install and testing water heater storage type (Geyser) single phase 230V , 50m HZ , 5 star energy saving high density PUF insulation tank made of heavy duty magnesium anode rod with steel core to protect enamelled tank from rust & corrosion , vertical insulation type 50 liter Cap 2000 watt rated power , incoloy 800 glass coated heating element , inner tank coating of feroglas powder, tank made of ultra thick super cold rolled steel plates , rated pressure 0.8 MPa, IPX4 protection consist of safety valve , thermal cut off , thermostat including connecting up and fixing arrangement on wall including proving hole fastners-04 nos hot and cold water metallic flexible pipe 15 mm bore of adequate length as provided by OEM or required at site -02 Nos , non return valve-01 nos and including necessary plumbing work, complete with integrated shock safe plug with all protection features as per OEM design and standard all as specified and directed. Note - QR code made of vinyl with UV laminate must be pasted on each geyser which will indicate CA No, Job No and name of contactor . Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysNov 20, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender