Tender For Construction Of Sp Type Structures (Jawan Barrack, Bop Comdr (O&R),Qg / Kote, Kitchen Cum Dining Hall And Toilet Cum Bathroom At Bop Survita (Balubari) Of 12Th Bn Kishanganj
Tender Value
1.19 Crore
Estimated cost
Bid Submission
17 Nov 2026
15 days left
EMD
2.38 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Darjeeling → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Sp Type Structures (Jawan Barrack, Bop Comdr (O&R),Qg / Kote, Kitchen Cum Dining Hall And Toilet Cum Bathroom At Bop Survita (Balubari) Of 12Th Bn Kishanganj
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and for all lift |
| 3 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 Cement 4 coarse sand (zone-III) derived from natural sources 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. |
| 7 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size de rived from natural sources) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircase and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete. |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform |
| 14 | Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 15 | Centering and shuttering including strutting, propping etc. and removal of form for: Columns, Pillars, Piers, Abutments, Posts and Struts |
| 16 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars |
| 17 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars |
| 18 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 19 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in: Cement mortar 1:6 (1 cement: 6 coarse sand) |
| 20 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) |
| 21 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 22 | Providing and fixing ISI marked flush door shutters conforming to IS 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 23 | 9.21 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part 1) non-decorative type 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws |
| 24 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws: 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Kiln seasoned selected class of sheesham wood |
| 25 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding |
| 26 | Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size). |
| 27 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete: '250x16 mm |
| 28 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 250x10 mm |
| 29 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 150x10 mm |
| 30 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete: 125 mm |
| 31 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper |
| 32 | 35 mm thick factory made soild panel pvc door shutter made out o singal piece extruded soiled pvc profile 5mm thick, having styles & rails (95mm x35mmx5mm) out of wich 75mm shall be flat and 20mm shall be tapered having one side thickness of 15 mm interally extruded on the hinge side of the profile for better screw holding power…… non decorative finish . |
| 33 | Providing and fixing factory made upvc door framed made of upvc exturded section of size 65mmx55 mm with wall thickness corner of the door frame to be mitred cut and joinet with plastic brackets and stainless steinless steel screws.... Direction of engineer in charge. |
| 34 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 35 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thikness, including hinges, jamb, lock jamb, bead and if required angle threshhold of mild steel angal of section 50x25 mm, or base ties of 1.60 mm pressed mild steel welded or rigidly fixed together by mechanincal means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in charge:, |
| 36 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 37 | Steel work in built up sections / framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc as required |
| 38 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : |
| 39 | Providing and laying Ceramic glazed floor tiles of size300x300mm (thikness to be specified by the manufacture) of 1st quality conforming to IS 15622 of approved make in colorus such as white , lvory, grey, Fume red Brown laid on 20mm thick cement mortar 1:4. |
| 40 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm |
| 41 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.size of tile 600x600 mm |
| 42 | Providing and laying Polished Granite stone flooring in required design… Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 43 | Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm c/c, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90 mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450 mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64 mm dia x 230 mm long G.I wire at every junction, including fixing perimeter channels 0.50 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25 mm at 230 mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150 mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture’s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 44 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 45 | Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500-600mm) |
| 46 | 12 mm cement plaster of mix: 1:4 (1 cement: 4 fine sand) |
| 47 | 15 mm cement plaster on the rough side of single or half brick wall of mix: 1:4 (1 cement: 4 fine sand) |
| 48 | 12 mm cement plaster finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) |
| 49 | Neat cement punning |
| 50 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 51 | Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 52 | Applying priming coat: With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 53 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 54 | Providing and applying white cement based putty of avarge thiknes 1mm of apporved brand and manufacture, over the plastered wall surface to prepar the surface evan and smooth complet. |
| 55 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushingcistern, including flush pipe, with manually controlled device (handle lever)conforming to IS : 7231, with all fittings and fixtures complete, includingcutting and making good the walls and floors wherever required: |
| 56 | Providing and fixing white virteous china pedestal type water closet (European type W.C. Pan) with seat and lid , 10 ltr low level white PVC flushing cistern, including flush pipe, with manually controlleddevice (handle lever) conforming to IS 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 57 | Providing and fixing wash basin with CI brackets, 15mm CP brasspillar taps, 32mm CP brass waste of standard patten, including painting of fittings and brackets cutting and making good the walls whereever required: |
| 58 | Providing and fixing stainless steel A ISI 304 (18/8) kitchen sink as IS 13983 with C.I brackets and stainless steel plug 40 mm , including painting of fittings and brackets, cutting and making good the walls whereever required: |
| 59 | Proving and fixing white vitreous chine flate back or wall cover typelopped front urinal bath of 430 x 260 x350 mm or 340 x410 x265 mm size respectively. |
| 60 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 32 mm dia |
| 61 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 62 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm |
| 63 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawlplugs etc., complete. |
| 64 | Providing and fixing toilet paper holder: C.P. brass |
| 65 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix, including cost of cutting holes and making good the walls etc. For 100 mm dia pipe |
| 66 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 1729 |
| 67 | Providing and fixing collar: 75 mm Sand cast iron S&S as per IS - 1729 |
| 68 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. |
| 69 | Prividing and fixing Chlorinated pllyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting s this including jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge Extemal work 20mm nominal dia pipes. |
| 70 | Prividing and fixing Chlorinated pllyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting s this including jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge Extemal work 32 mm nominal dia Pipes |
| 71 | Prividing and fixing Chlorinated pllyvinyl chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting s this including jointing of pipes & fitting with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge Extemal work 50 mm nominal dia Pipes |
| 72 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 32 mm nominal bore. |
| 73 | Providing and fixing gun metal non-return valve of approved quality (screwed end): 25 mm nominal bore Vertical |
| 74 | Providing and fixing unplasticised PVC connection pipe with brass unions: 30 cm length 15 mm nominal bore |
| 75 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 150 mm diameter |
| 76 | Providing and fixing G.I union in G.I pipe including cutting and threading the pipe and making long serews etc complete (new work).15 mm nominal bore. |
| 77 | Providing and fixing G.I uion in G.I pipe including cutting and threading the pipe and making long screws etc. complete (New work) .25 mm nominal bore. |
| 78 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet outlet and overflow pipes but without fittings and the base support for tank. |
| 79 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal bore |
| 80 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standard and weighing not less than 810 gms. |
| 81 | Providing and fixing C.P. brass stop cock (concealed) conforming to IS:8931. 15 mm nominal bore |
| 82 | Providing and fixing C.P. Brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931. |
| 83 | Providing and fixing PTMT pillar cock of approved quality and colour. 15 mm nominal bore, 107 mm long |
| 84 | Constructing brick masonry chamber for underground C.I. inspection chamber Inside dimensions 455x610 mm and 45 cm deep for single pipe line: With common burnt clay F.P.S. bricks of class designation 7.5 |
| 85 | Making soak pit 2.5m diameter 3.0 meter deep with 45x45 cm dry brick honey cmb shaft with bricks and S.w. drain pipe 100 mm diameter , 1.8 m long complete as per standard design. |
| 86 | Providing and fixing aluminium work for door, windows,ventilators and partitions with extuded bulit up standerd tubular section /appropriate Z section and other section of approved make conforming to IS 733 and IS :733 and IS 1285, fixing with dash fasteners of required dia and size including necessary filling up the gaps at junction ie. at top bottom and side with requried EPDM rubber/neoprene gasket etc. Aluminium snap beadingfor glazing paneling, CP brass/stainless steel screws all completed as per architectural drawing and the direction of Engineer -in charge .(Glazing, Paneling and dash fasteners to be paid for separately) for fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS 1868 minimum anodic coating of grade Ac 15) |
| 87 | For shutters of doors, windows & ventilators including hinges/pivots... For shutters of door windows & ventilators including providing and fxing hinges /pivots and making provision for fixing of fitting whererever required including the cost of EPDM rubber/neoprene gasket required (fitting shall be paid for separately Anodised aluminium anodised transparent or dyed to required shade according to is : 1868, minimum anodic coating of grade AC15). |
| 88 | Providing and fixing soil: Waste and vent pipe 100 mm PVC pipe |
| 89 | Providing and fixing soil, waste and vent pipe: 75 mm PVC Pipe |
| 90 | Providing and fixing bend with access door: 100 mm PVC pipe |
| 91 | Wiring for light point/fan point/exhaust fan point/call bell point with 1.5sq mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, with piano type switch, phenolic laminated sheel, suitable size MS box and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. as requied Group A |
| 92 | Wiring for light/power plug with 2x4 sq mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 93 | Wiring for light/power plug with FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith insulated copper conductor single core cable for loop earthing as required.Wiring for circuit/ submain wiring alongwith earth wire… 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 94 | Supplying and fixing following mdular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc5/6 A switch |
| 95 | Supplying and fixing following mdular switch/socket on the existing modular plate & switch box including connections but excluding modular plate etc3 pin 5/6 A socket outlet |
| 96 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required. |
| 97 | Supplying and fixing following way, single pole and neutral , sheet steel MCB distribution board, 240V on surface/ recess, complete with tinned copper bus bar, interconnections, power painted including earthing etc as required (But without MCB/RCCB/Isolator) 8 way, Double door |
| 98 | Supplying and fixing 5A to 32 A rating. 240/415V, 10KA C'' curve miniature circuit breaker suitable for inductive load of following poles in the existing MOB DB complete with connections , testing and commissioning etc. as required Single pole |
| 99 | Supplying and fixing following rating double pole, 240V isolator in the existing MOB DB complete with connections , testing and commissioning etc. as required 40A |
| 100 | Earthing with G.I earth pipe 4.5 meter long 40mm dia inclusing accessories and provideing masonry enclosure with cover plate having locking arrangement and watering pipe etc with charcoal /coke and salt as required. |
| 101 | Earthing with G.I earth plate 600x600x6mm thick including accessories and provideing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. (but without charcoal /coke and salt) as required. |
| 102 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I thimble excavation and re- fitting as required. |
| 103 | Providing and fixing of lightning conductor finial,made of 25mm dia 300mm long G.I tube, having single prong at top,with 85mm dia 6mm thick G.I base plate including holes etc. complete as required. |
| 104 | Providing and fixing G.I tape 20mm x 3 mm thick on para pet or surface of wall for lighting conducter complete as required for horigental run. |
| 105 | Supply, Installation, Testing and Commissioning of 1200mm sweep, Bee 5 star rated, Ceiling Fan with Brush Less Direct Current (BLOC) Motor, class of insulation ;B 3 nos caropies , shackle kit, safety rope, copper winding , power Factor not less than 0.9 Service Value (CM/M/W) minium 6.00 Air delivery minimum 210 Cum/Min,350 RPM (tolerance as per IS 375-2019) THD less than 10% remote or electrinic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers temperature rise=75 degreeC(max) insulation resistance more tha 2 mega ohm, suitable for 230v, 50 Hz single phase AC Supply, earthing etc complete as required. |
| 106 | Providingand fixing metal box (size 150x75x60) |
| 107 | Providing and fixing of 15 watt LED bulb with necessary fitting ( Brand : Havells , Suriya, Phillips) by Engineer in Charge). |
| 108 | Providing and fixing jof 35/40 watt LED Tube Light with necessary fitting (Brand; Hevells, Suriya, Philips) by Enginner in Charge. |
| 109 | Providing and fixing fluroscent lamp-11 watt of approved brand |
| 110 | Providing and fixing of exhaust fan with necessary fitting (Brad: Havells, Suriya, Philips) By Engineer in charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 18, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender