Tender For Construction Of Techno-Park-Cum-Multi-Agro Processing Plant Under Capex/Rbic At Cots Mirgund, Skuast-K.
Tender Value
15.01 Crore
Estimated cost
Bid Submission
16 Nov 2026
12 days left
EMD
30.02 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Srinagar → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Techno-Park-Cum-Multi-Agro Processing Plant Under Capex/Rbic At Cots Mirgund, Skuast-K.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-Oct-2026 | item corrigendum | Other | 16-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | STRUCTURAL PART |
| 2 | Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. (Including dewatering if any upto plinth level)All kinds of soil : |
| 3 | STONE SOLING: Providing and laying of hand packed stone soling (size 100mm-150 mm), before laying of mud mat, compacted, consolidated, rammed and filling the voids with fine sand - all complete incl carriage upto site of work with all head loads. |
| 4 | MUDMAT: Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) |
| 5 | MASS CONCRETE: Providing and laying mass concrete1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in Below Ground and Above Grouns Plinth retaining walls, (any thickness) including attached pilasters, including curing but excluding the cost of centring, shuttering and finishing with. |
| 6 | CAST-IN-STU DESIGN MIX M25: Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix,incluyding pumping of concrete to site laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportiond as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. |
| 7 | UPTO PLINTH LEVEL |
| 8 | ABOVE PLINTH LEVEL |
| 9 | FORM WORK: Centering and shuttering including strutting, propping etc. and removal of formwork from the site, for all works from foundations, to roof level. |
| 10 | BELOW PLINTH LEVEL |
| 11 | ABOVE PLINTH LEVEL |
| 12 | SLAB EDGES |
| 13 | PLINTH FILLING: Supplying and filling in plinth with GSB/ Second class sand under floors including, watering, ramming, consolidating and dressing complete including carriage, leads and lifts. |
| 14 | BACK FILLING: Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m. |
| 15 | STEEL REINFORCEMENT: Steel reinforcement for R.C.C. works including straightening, cutting, bending, placing in position and binding - all complete from foundation to roof level of Thermo-Mechanically Treated bars of grade Fe-500D or higher. |
| 16 | EXPANSION JOINT |
| 17 | FLOOR |
| 18 | WALLS |
| 19 | STRUCTURAL STEEL:Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. plates, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer also included |
| 20 | ANCHOR BOLTS: Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. |
| 21 | ARCHITECTURAL PART (PART-A) |
| 22 | Brick work with FPS bricks in 1:6 mix cement mortar above plinth level upto floor V level complete |
| 23 | 12 mm thick cement plaster (1:6) in walls |
| 24 | 6mm thick plastering in cielings (1:4) |
| 25 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. (50 mm thick ) |
| 26 | Pointing on exposed brick masonry external surfaces with lime surkhi finish (I Lime: 2 Surkhi ) mixing in approved proportion, including raking out joints, cleaning and preparation of surface, applying and finishing joints in ruled/pointed pattern as directed, curing, including grinding the brick surface where required, finishing true to line, level and plumb, complete in all respects including cost of all materials involved, including scaffolding/staging and all incidental charges as directed by the Engineer-in-Charge. |
| 27 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. The job includes Railing as per per Arch design and Hand rail for the staircases. |
| 28 | Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick |
| 29 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over& including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 30 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 31 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades of any size as approved by Engineer- in-Charge, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, of( size 1200 x 600 mm). |
| 32 | Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).(Size of tile 1200x600 mm) |
| 33 | KOTA STONE FLOORINGKota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) : |
| 34 | P/F of cheaseled devri stone cladding upto 35 mm thickness laid in cement sand mortor ratio 1:3,including pointing work and as per the design as desired by engineer incharge all complete job. |
| 35 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class Deodar wood |
| 36 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.Glass DGU (6+12+6) Sample to be approved by EIC. |
| 37 | Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 38 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.With ISI marked M.S. pressed butt hinges bright finished of requiredsize with necessary screws 35mm Thick. |
| 39 | P/F of 5mm Thick glass including cost of kail wood beading fixed the cost of fittings and fixtures approved specifications |
| 40 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete |
| 41 | Providing & Fixing Aluminium ISI marked fittings to doors , windows, of required colour and shade with necessary screws etc complete |
| 42 | T-Bolts 150mm |
| 43 | Handles 150mm |
| 44 | Aldrop with locking arrangements 250mm |
| 45 | Providing and fixing plained eaves boarding.2nd class kail wood 300x40 mm (nominal size). |
| 46 | Providing and fixing 12mm thick T&G planks made of imported wood (New zealand pine or equivalent) on wood work in false ceiling, wall/wall partitions sawn and put up in position ( budloo wood Ceiling Joists of 50 mm x 65 mm in sections placed @ 600 mm C/C both ways or as required at site). including cost of necessary adhesive & cost of nails etc. all complete upto floor 5 level as per the directions of Engineer-in-charge (including cost of all material, leads, lifts and carriages etc upto site of work complete).(For panelling /Ceilings/Soffits etc.) |
| 47 | Providing and fixing Track deck CRIL make or equivalent H.I. rib profiled sheets 1000 to 1020 mm cover width 28-35 mm high crests at 250 to 255 mm T.C.T(total coated thickness) high tensile S.M.P Galvalume steel. The sheets shall have wide panes with 3 no stiffing ribs, effective water shedding and special male/female ends with full return legs on side Lapps for purlins support and anti-capillary flute inside Lapp. The sheets shall have a hot dip metallic coated of zinc and aluminum (150 gms /sm) zinc/aluminum coating mass total on both sides AZ-150 as IS -1397 ,550 MPA yield stress. Providing silicon modified polyester coating of approved colour of total thickness of 35 micron comprising 20 micron exterior coat of S.M.P over 5 micron polyester back coat over 5 micron primer coats on both surfaces including side and end Lapp and using 8mm Galvalume hex self-drilling fastener on each crest of sheet for connection with purlins and seam bolts at 300mm centers on all sides and end Lapps etc (.measured for unit of laid area) (0.50 mm thickness ) |
| 48 | Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges/Valley plain (500 - 600mm) |
| 49 | Supplying and applying waterproofing at plinth level, sunken portions,washroom room area etc. using pre applied, pressure sensitive HDPE membrane as per specifications listed below with guarantee period of 10 years: Supplying and installing of 1.2 mm thick self adhesive HDPE membrane conforming to BS 8102, IS 16471 Type I standard for below ground structures, having puncture resistance of 1000 N (as per ASTM E 154) and hydrostatic head resistance not less than 60 m head (ASTM D 5385), tensile strength of 25 Mpa (ASTM D 412), & elongation of min. 500% (ASTM D 412), peel adhesion to concrete of 880 N/m (As per ASTM D 903 modified). The membrane should be comprising of a min HDPE layer of 0.8 mm and a pressure sensitive adhesive layer which is covered by a weather proof protective and trafficable granular layer of sand to protect self adhesive polymer layer. Place the membrane HDPE film side to the substrate with adhesive facing towards the concrete pour. End laps should be staggered to avoid a build-up of layers. Leave the membrane loosely laid, in position until overlap procedure is completed. Accurately position succeeding sheets to overlap the previous sheet 75 mm along the marked selvedge and edges shall be sealed. Ensure the underside of the succeeding sheet is clean, dry and free from contamination before attempting to overlap. At the end of each role, the grains should be removed by using hot air shovel gun & the joint between two sheets should be sealed with the help of double side tape. |
| 50 | Providing and fixing aluminum work for Partition including doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z, sections and other sections of approved make conforming to IS:733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fastners incl. necessary filling up of gaps at junctions, at top, bottom & sides with required PVC/ neoprene felt etc. Aluminum sections shall be smooth, rust free, straight, mitred & jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing / paneling, C.P. brass/stainless steel screws including all hardware fittings as required, (with 5 mm thick glazing and A.C.P paneling of 4 mm thickness and of required sizes including hydraulic door springs, G-channels 6' long and sliding wheels for doors and Handles etc and inbuilt locks all necessary fittings Wherever required all complete as per architectural drawings & the directions of Engineer-in-Charge Partition with 100 mmx 44 mm 14 gauge Powder Coated Section , Door profile 81.25 mm x 44 mm 14 gauge (Powder coated aluminum (minimum thickness of powder coated 50 microns ) |
| 51 | Providing and fixing false ceiling with 12 mm thick plain/ semi perforated or with design ceiling tiles of BWP type phenol formaldehyde synthetic resin bonded pressed particle board conforming to IS:3087, finished with a coat of aluminum primer on both sides & edges, including two coats of synthetic enamel paint of approved quality on exposed face, fixed to a grid made out of anodized aluminum (with 15 micron anodic coating) Tsections 35 x15x1.5 mm size main runners, cross runners 23.5x19x1.5 mm fixed to main runners placed 600 mm centre to centre both ways so as to form a grid of 600 mm square. The frame work shall be suspended from ceiling by level adjusting hangers of 6 mm dia M.S rod fixed to roof slab by means of ceiling cleats and dash fastener. The suspenders shall be placed 600 x 1200 mm centre to centre including fixing to the frame with C.P brass screws and applying a priming coat of zinc chromate yellow primer (aluminum frame work shall be paid separately). |
| 52 | Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of tile 1200x600 mm |
| 53 | French spirit polishing, Two or more coats on new works including a coatof wood filler |
| 54 | Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. With resin bonded rock wool with density 48 kg/cum |
| 55 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work |
| 56 | Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) |
| 57 | Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 58 | PART-B |
| 59 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations,drains,pipes,cables,etc (not exceeding 1.5 m in width) and for shafts,wells,cesspits and the like not exceeding 10sqm on plan,includingdressing of sides and ramming of bottoms lift upto 1.5m,including getting out excavated earth and disposal of surplus excavated earth as directed,within a lead of 50 metres:(code no 2.9.1) all kinds of soil |
| 60 | Providing/ laying position cement concrete of specified grade excl. cost of centering and shuttering all work upto plinth level 1:4:8 ( stone agg. 40mm nom. Size) |
| 61 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 62 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 63 | Random Rubble masonry with hard stone in foundation and plinthincluding leveling up with cement concrete 1:6:12 (1 Cement : 6 coarsesand : 12 graded stone aggregate 20mm nominal size) upto plinth level andcuring complete with:Cement mortar 1:6 (1 Cement : 6 coarse sand) Quarry |
| 64 | Constructing brick masonarry collection chambers 600X600 internal size and 600mm deep fixed with C I cover and frame 450x450 mm |
| 65 | PLUMBING |
| 66 | Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. |
| 67 | PN-20 pipe, 25mm OD (SDR-7.4) |
| 68 | External work including trenching, refilling etc |
| 69 | PN-20 pipe, 25mm OD (SDR-7.4) |
| 70 | PN-20 pipe, 32mm OD (SDR-7.4) |
| 71 | PN-20 pipe, 40mm OD (SDR-7.4) |
| 72 | Providing and fixing PPR Unions |
| 73 | PPR Union 25mm |
| 74 | PPR Union 32mm |
| 75 | PPR Union 40mm |
| 76 | Providing and fixing G.I. pipes complete with G.I. fittings excluding trenching and refilling etc. (external work) |
| 77 | 40 mm dia. nominal bore (Medium) |
| 78 | Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work. 40 mm and 50 mm dia. G.I. pipes |
| 79 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore |
| 80 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete |
| 81 | 25 mm día |
| 82 | 32 mm dia. |
| 83 | 40 mm dia |
| 84 | 50 mm dia |
| 85 | 40 mm dia ball valve for main distribution line |
| 86 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes, but without fittings and base support for tank |
| 87 | Providing and fixing G.I. tanky nipple with nuts etc. all complete |
| 88 | SANITARY FITTINGS |
| 89 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid |
| 90 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 91 | Providing and fixing CP towel ring with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms. |
| 92 | Providing and fixing 45 to 60 cm long PVC connections of superior Quality 15 mm Nominal bore |
| 93 | Providing and fixing PTMT liquid soap container 109 mm wide. 125 mm high and 1112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms |
| 94 | Providing and fixing toilet paper holder C.P. brass |
| 95 | Providing, fixing, testing and commissioning of star white colour vitreous china below / over counter Oval Wash Basin / circular basin (Size 560 x 410 mm or as/architectural detail drawing) with CP brass waste assembly complete including CI/MS brackets duly painted, cutting and making good the walls floors wherever required |
| 96 | Providing and Fixing, testing & commissioning of ABS Health Faucet 3 (CP) (complete with hook and flexible tube min. Length 1.0 m) as required complete in all respect |
| 97 | Providing and fixing 15 mm nominal bore C.P. brass angle valve for 0 basin mixer and geyser points of approved make conforming to IS: 8931 |
| 98 | Providing and fixing PVC waste pipe of approved make Flexible pipe (32-40 mm dia) |
| 99 | Providing and fixing CP waste (Coupling) of approved make. (31-85mm length) and breedth (62-77mm) weight not less than (45-60 gms) |
| 100 | Providing, fixing, testing and commissioning of C.P. brass single hole basin mixer with CP wall flange, swinging spout complete as required and making good |
| 101 | Fixing white vitreous china urinal basin: One urinal basin with 5 liter white P.V.C automatic flushing cistern. |
| 102 | Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with ½\\" BSP thread and shapes, weighing not less than 60 gms |
| 103 | Providing and fixing urinal partition made of 10 mm thick toughened /tempered glass of approved shade and quality, with polished edges, corner rounding, necessary stainless steel/brass heavy duty brackets, fittings and fixtures complete, fixed true to line and plumb, including drilling, cutting, making good the walls/floor and all incidental works, complete in all respects as directed by the Engineer-in-Charge. |
| 104 | Providing and fixing CP square shaped grating of approved quality & make and as per the direction of Engineer-in-charge |
| 105 | Providing and fixing C.P. Brass extension nipple (size 15mm 50mm) of approved make and quality as per direction of Engineer-incharge. |
| 106 | Providing and fixing C.P. Brass extension nipple (size 15mmx70mm) of approved make and quality as per direction of Engineer-incharge. |
| 107 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required, Kitchen sink without drain board 610x460mm bowl depth 200mm |
| 108 | Providing and fixing sink mixer long nose of approved make |
| 109 | Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste and 40 mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the walls wherever required, Size 600x450x200 mm |
| 110 | SOIL, WASTE, RAIN WATER AND VENT PIPES |
| 111 | Providing, fixing, testing and commissioning of PVC pipe type 'B' with all fittings such as bends, tees, elbow, offset, clamps etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The jointing to be completed with rubber ring joint/solvent weld joint as required |
| 112 | 50mm dia |
| 113 | 75mm dia |
| 114 | 100 mm dia |
| 115 | 150 mm dia |
| 116 | providing, fixing floor trap 110mm Dia OD Including testing of joints etc all complete. |
| 117 | Carraige of materials from source to site of work |
| 118 | Carraige of stone soling/stones for a lead of 13 km from Baramulla by M.T |
| 119 | Carraige of sand for a lead of 13 km from Juhama by M.T |
| 120 | Carraige of crusher bajri for a lead of 13 km from kuner by M.T |
| 121 | Carraige of bricks for a lead of 32 km from Budgam by M.T |
| 122 | Note:-The rates quoted are inclusive of all carriages of materials (Mechanical/Manual) from source to site work and all extra charges including dewatering if any during the execution of work complete in all respects. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 16, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 12 daysNov 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender