Tender for Tender for Construction Of 06 Type-3 Residential Units For Employees In The Pwd Colony, Saharanpur District.
Tender Value
1.80 Crore
Estimated cost
Bid Submission
03 Nov 2026
4 days left
EMD
11 Lakhs
Bank guarantee accepted
Document Fee
2714
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Saharanpur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of 06 Type-3 Residential Units For Employees In The Pwd Colony, Saharanpur District.
BOQ
| Sl. No. | Item Description |
| 1 | Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 2.31) |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. DSR- 2.8.1. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 2.8.1) |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 2.25) |
| 4 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 2.25(a) |
| 5 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 2.27) |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 4.1.8) |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Rates are exclusive of labour cess and GST and inclusive of all other taxes. All works upto plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum (DSR. No. 5.33.1.1) |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Rates are exclusive of labour cess and GST and inclusive of all other taxes. All works above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum (DSR. No. 5.33.2.1) |
| 9 | Add for using extra cement in the items of design mix over and above the specified cement content therein. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Foundations, footings, bases of columns, etc. for mass concrete (DSR No. 5.9.1) |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Suspended floors, roofs, landings, balconies and access platform (DSR No. 5.9.3) |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Lintels, beams, plinth beams, girders, bressumers and cantilevers (DSR No. 5.9.5) |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Columns, Pillars, Piers, Abutments, Posts and Struts (DSR No. 5.9.6) |
| 14 | Brick Work with common burnt clay F.P.S (non modular) brick of class designation 7.5 in foundation and plinth in : Cement mortar 1:6 (1 cement : 6 coarse sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 6.1.2) |
| 15 | Brick Work with common burnt clay F.P.S (non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 6.4.2) |
| 16 | Half Brick masonary with common burnt clay F.P.S (non modular) brick of class designation 7.5 in super structure above plinth level up to floor V level Cement mortar 1:4 (1 cement : 4 coarse sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 6.13.2) |
| 17 | Providing and Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 4.13) |
| 18 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 2.35.3.1) |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 5.22.6) |
| 20 | Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :. 250x16 mm. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 9.96.2) |
| 21 | Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : 250x10 mm. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 9.97.2) |
| 22 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125mm. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 9.165.1) |
| 23 | Providing and fixing cuboard shutter with 19 mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2 mm thick PVC edege banding tape with hot glue by edege bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge. (Payment of providing and fixing auto closing hinges shall be paid separately). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 9.168) |
| 24 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 9.48.1) |
| 25 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Using M.S. angels 40x40x6 mm for diagonal braces. (DSR No. 10.5.1) |
| 26 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 10.28 |
| 27 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Fixing with 15x3 mm lugs 10 cm. long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). (DSR No. 10.15.1) |
| 28 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 meter). (DSR No. 9.147.A4.1) |
| 29 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod pf approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS:16231 shall be paid separately. Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system, (Height upto 1.8m). (DSR No. 9.147.A4.2) |
| 30 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. : 30 mm thick. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 31 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: Rates are exclusive of labour cess and GST and inclusive of all other taxes. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (DSR. No. 9.21.1) |
| 32 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 1.0 mm thick. (DSR. No. 9.127.2) |
| 33 | Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws: Rates are exclusive of labour cess and GST and inclusive of all other taxes. 35mm thick shutter With ISI marked stainless steel butt hinges of required size Second class teak wood (DSR No. 9.134.1.2.1) |
| 34 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.50 mm all complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. With 2nd class teak wood beading 62X19 mm. (DSR No. 9.135.1) |
| 35 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 36 | 12 mm cement plaster : Rates are exclusive of labour cess and GST and inclusive of all other taxes. 1:6 (1 cement : 6 coarse sand) (DSR No. 13.4.2) |
| 37 | 15 mm cement plaster on rough side of single or half brick wall of mix: Rates are exclusive of labour cess and GST and inclusive of all other taxes. 1:6 (1 cement : 6 coarse sand) (DSR No. 13.5.2) |
| 38 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 39 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 40 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Double charge vitrified tile polished finish of size of Tile 600 x 600 mm (DSR No. 11.41A.1.1) |
| 41 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm (DSR No. 8.2.1.2) |
| 42 | Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick , Granite of any colour and shade. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 8.9.1.2) |
| 43 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Rates are exclusive of labour cess and GST and inclusive of all other taxes. New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre (DSR. No. 13.41.1) |
| 44 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 13.46.1) |
| 45 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 13.80) |
| 46 | Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 4.17) |
| 47 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 6.44) |
| 48 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: A-Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. B-Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. C-After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 22.7.1) |
| 49 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) - Dark shade pigment using ordinary cement. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR. No. 11.20.3) |
| 50 | WATER SUPPLY AND SANITARY WORK (as per WS BOQ. F TYPE III (G+1)) |
| 51 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : Rates are exclusive of labour cess and GST and inclusive of all other taxes. White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests (DSR. No. 17.1.1) |
| 52 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Rates are exclusive of labour cess and GST and inclusive of all other taxes. W.C. pan with ISI marked white solid plastic seat and lid (DSR No. 17.2.1) |
| 53 | Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls where required : Rates are exclusive of labour cess and GST and inclusive of all other taxes. White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps (DSR No. 17.7.3) |
| 54 | Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Sink with drain board 510x1040 mm bowl depth 225 mm (DSR No. 17.10.1.2) |
| 55 | Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Flexible Pipe 32mm dia (DSR No. 17.28.2.1) |
| 56 | Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Flexible Pipe 40mm dia (DSR No. 17.28.2.2) |
| 57 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Circular shape 450 mm dia (DSR No. 17.32.1) |
| 58 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 59 | Providing and fixing toilet paper holder : Rates are exclusive of labour cess and GST and inclusive of all other taxes. C.P. brass (DSR No. 17.34.1) |
| 60 | Providing and fixing soil, waste, vent pipes. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100 MM DIA Centrifugal cast (spun) iron socket & spigot (s&s) pipe as per IS:3989 (DSR No. 17.35.1.2) |
| 61 | Providing and fixing MS holder bat clamps of approved design to PVC pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. For 100mm dia. Pipe (DSR No. 17.37.1) |
| 62 | Providing and fixing heel rest sanitary bend. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100mm (DSR No. 17.40.1.2) |
| 63 | Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100X100X100mm Sand cast iron S&S as per IS - 3989 |
| 64 | Providing and fixingPLAIN JUNCTION of required degree. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100X100X100mm Sand cast iron S&S as per IS - 3989 |
| 65 | Providing and fixing terminal guard: Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100mm Sand cast iron S&S as per IS - 3989 (DSR No. 17.56.1.2) |
| 66 | Providing and fixing collar. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100mm Sand cast iron S&S as per IS - 3989 (DSR No. 17.57.1.2) |
| 67 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter: Rates are exclusive of labour cess and GST and inclusive of all other taxes. 100 Dia (DSR No. 17.58.1) |
| 68 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : Rates are exclusive of labour cess and GST and inclusive of all other taxes. Sand cast iron S&S as per IS: 3989. (DSR No. 17.60.1.1) |
| 69 | Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour weighing not less than 105 gms. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 70 | Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 71 | Providing and fixing PTMT towel rail complete with brackets fixed wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms (DSR No. 17.73.2) |
| 72 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge..Internal work - Exposed on wall. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 15 mm dia nominal bore (DSR No. 18.7.1) |
| 73 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge..Internal work - Exposed on wall. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 20 mm dia nominal bore (DSR No. 18.7.2) |
| 74 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge..Internal work - Exposed on wall. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 25 mm dia nominal bore (DSR No. 18.7.3) |
| 75 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 15 mm nominal outer dia pipes (DSR No. 18.8.1) |
| 76 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 20 mm nominal outer dia pipes (DSR No. 18.8.2) |
| 77 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 50 mm dia, nominal bore (DSR No. 18.9.6) |
| 78 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends). Rates are exclusive of labour cess and GST and inclusive of all other taxes. 25mm dia, nominal bore (DSR No. 18.17.1) |
| 79 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends). Rates are exclusive of labour cess and GST and inclusive of all other taxes. 50 mm dia, nominal bore (DSR No. 18.17.4) |
| 80 | Providing and fixing uplasticised PVC connection pipe with brass unions : Rates are exclusive of labour cess and GST and inclusive of all other taxes. 45 cm length 15 mm nominal bore (DSR No. 18.21.2.1) |
| 81 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 82 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 15mm nominal bore (DSR No. 18.49.1) |
| 83 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 15mm nominal bore (DSR No. 18.51.1) |
| 84 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 15 mm nominal bore (DSR No. 18.53.1) |
| 85 | Providing and fixing PTMT grating of approved quality and colour. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Circular type 100 mm nominal dia (DSR 18.58.1.1) |
| 86 | SCHEDULE OF QUANTITIES FOR INTERNAL SEWERAGE SYSTEM - IV |
| 87 | Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,. Rates are exclusive of labour cess and GST and inclusive of all other taxes. in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia. (DSR No. 2.10.1.2) |
| 88 | Providing and laying Non pressure NP 2 class (light duty) RCC pipe with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand ) including testing of joints etc. complete. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 150mm diameter (DSR No. 19.6.2) |
| 89 | Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand : 10 graded stone aggregate 40mm nominal size) upto the haunches of pipes including bed concrete as per standard design. Rates are exclusive of labour cess and GST and inclusive of all other taxes. 150mm diameter S.W. Pipe (DSR No. 19.3.2) |
| 90 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of .class designation 7.5. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 91 | Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design. Rates are exclusive of labour cess and GST and inclusive of all other taxes. Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg). With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (i) For Sewer Line (DSR No. 19.7.1.1) |
| 92 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Rates are exclusive of labour cess and GST and inclusive of all other taxes. |
| 93 | EXTERNAL DEVELOPMENT WORK (RAIN WATER HARVESTING PIT 1 No., BORING 1 No., SEPTIC TANK FOR 35 USERS WITH SOAK PIT 1 No.) |
| 94 | Excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.5 metre and lead upto 30 m, including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 m (rate is including royalty). From 0.00 m to 1.50 m depth. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 2.6.1) |
| 95 | Excavation in foundation in ordinary soil (loam, clay or sand) including lift upto 1.5 metre and lead upto 30 m, including filling, watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30 m (rate is including royalty). From 0.00 m to 1.50 m depth. Rates are exclusive of labour cess and GST and inclusive of all other taxes. but for depth from 1.50 m to 3.00 m, including extra lift. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 2.6.1 and 2.26.1) |
| 96 | Brick work with common burnt clay (non modular) bricks of class designation 150 in foundation and plinth in cement mortar 1:4 (1 cement : 4 coarse sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 6.1.1) |
| 97 | 15 mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 13.10) |
| 98 | 12 mm cement plaster in single coat on rough side of single or half brick wall finished with a floating coat of neat cement : 1 cement : 3 coarse sand. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 13.9.1) |
| 99 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12-20 mm nominal size) laid in one layer finished with neat cement (40 mm thick floor). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 11.3.1) |
| 100 | Supply & laying of 40 mm gauge over burnt brick ballast including all materials, labour and T&P etc. for proper completion of the work. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 0287) |
| 101 | Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 19.15.1) |
| 102 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality : Circular shape 500 mm internal diameter. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 19.19.2.2) |
| 103 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality : Circular shape 450 mm internal diameter. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 19.19.1.3) |
| 104 | Providing and fixing soil, waste and vent pipes : 75 mm diameter : Centrifugally cast (spun) iron socketed pipe as per IS : 3989. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 17.35.2.2) |
| 105 | Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation M-150. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 19.32.1) |
| 106 | Drilling of 300 mm dia bore hole manually for rain water harvesting recharge bore, all complete as per direction of Engineer-in-charge. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.2.1.1) |
| 107 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS : 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge : 150 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.4.2) |
| 108 | Gravel packing in tubewell construction in accordance with IS : 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.8) |
| 109 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS : 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level : All types of soil - 300 mm dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.1.1.1) |
| 110 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS : 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge : 100 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.3.1) |
| 111 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS : 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths : 100 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.4.1) |
| 112 | Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.7) |
| 113 | Development of tube well in accordance with IS : 2800 (part I) and IS : 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by V notch method, measuring static level & draw down by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete including hire & labour charges of air compressor, tools & accessories etc. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.12) |
| 114 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of : 100 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.13.1) |
| 115 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS : 2800 (part I), including necessary bolts & nuts of required size complete : 100 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.14.1) |
| 116 | Providing and fixing bail plug/ bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (part I) : 100 mm nominal size dia. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 23.15.1) |
| 117 | Pumping set - KSB make submersible pump set suitable for installation in bore well of minimum 100 mm inner dia (preferably more) and having specifications as approved, 2.0 HP (E/P only). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (AS per MR) |
| 118 | Supply and fixing of Finolex make ISI marked copper submersible cable of size 4 sq mm, 3 core (E/P only). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (AS Per MR) |
| 119 | INTERNAL ELECTRIFICATION WORK Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Group A (DSR-25EM No. 1.10.1) |
| 120 | Wiring for twin control light point with 1.5 sq.mm FRLS/ HFFR PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. (DSR-25EM No. 1.11) |
| 121 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X2.5 sq. mm + 1X2.5 sq. mm earth wire (DSR-25EM No. 1.14.2) |
| 122 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire (DSR-25EM No. 1.14.3) |
| 123 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 6 sq. mm + 1 X 6 sq. mm earth wire (DSR-25EM No. 1.14.4) |
| 124 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 10 sq. mm + 1 X 6 sq. mm earth wire (DSR-25EM No. 1.14.5) |
| 125 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 16 sq. mm + 1 X 6 sq. mm earth wire (DSR-25EM No. 1.14.6) |
| 126 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair (DSR-25EM No. 1.18.2) |
| 127 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. (DSR-25EM No. 1.19) |
| 128 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm (DSR-25EM No. 1.21.1) |
| 129 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm (DSR-25EM No. 1.21.3) |
| 130 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 A switch (DSR-25EM No. 1.24.1) |
| 131 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 A switch (DSR-25EM No. 1.24.3) |
| 132 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 A socket outlet (DSR-25EM No. 1.24.4 ) |
| 133 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 A socket outlet (DSR-25EM No. 1.24.5) |
| 134 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet (DSR-25EM No. 1.24.6) |
| 135 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet (DSR-25EM No. 1.24.7) |
| 136 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. (DSR-25EM No. 1.25) |
| 137 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. (DSR-25EM No. 1.26) |
| 138 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm) (DSR-25EM No. 1.27.1) |
| 139 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 3 Module (100mmX75mm) (DSR-25EM No. 1.27.2) |
| 140 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required. 6 Module (200mmX75mm) (DSR-25EM No. 1.27.4) |
| 141 | Installation, Testing, Commissioning of wall bracket/ceiling fittings of all sizes and shapes containing upto two GLS/ CFL / LED lamps per fitting, complete with all accessories including connections etc. as required. (DSR-25EM No. 1.35) |
| 142 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Up to 450 mm sweep (DSR-25EM No. 1.50.1) |
| 143 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. (DSR-25EM No. 1.51) |
| 144 | Supplying & fixing suitable size Gl box with modular plate and cover in fronton surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. (DSR-25EM No. 1.57) |
| 145 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. (DSR-25EM No. 1.58) |
| 146 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) 8 way , Double door (DSR-25EM No. 2.3.2) |
| 147 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/lsolator) 12 way , Double door (DSR-25EM No. 2.3.3) |
| 148 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole (DSR-25EM No. 2.10.1) |
| 149 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. (DSR-25EM No. 2.11) |
| 150 | Supplying and fixing following rating, double pole, the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A (DSR-25EM No. 2.12.1) |
| 151 | Supplying and fixing following rating, double pole, the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A (DSR-25EM No. 2.12.2) |
| 152 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A (DSR-25EM No. 2.14.2) |
| 153 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 A (DSR-25EM No. 2.14.3) |
| 154 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. (DSR-25EM No. 2.21) |
| 155 | Sub-Head : EARTHINGEarthing with G.l. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. (DSR-25EM No. 5.4) |
| 156 | Supplying and laying 6 SWG G.l. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with Gl thimble etc. as required. (DSR-25EM No. 5.7) |
| 157 | Supplying and laying 25 mm X 5 mm G.l. strip at 0.50 metre below ground as strip earth electrode, including connection / terminating with G.l. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.l. nut bolt & spring washer spaced at 50mm) (DSR-25EM No. 5.9) |
| 158 | Providing and fixing 25 mm X 5 mm G.l. strip on surface or in recess for connections etc. as required. (DSR-25EM No. 5.15) |
| 159 | Providing and fixing 6 SWG dia G.l. wire on surface or in recess for loop earthing as required. (DSR-25EM No. 5.16) |
| 160 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3-1/2 X 35 sq.mm (DSR-25EM No. 11.1.21) |
| 161 | Sub-Head : MISC. CIVIL ITEMSProviding and fixing circular/Hexagonal G.I. Box forceiling fan clamps, of internal dia 140 mm, 73 mm height, top LID of 1.5 mm thick G.I. sheet with its top surface hacked for proper bonding, top LID shall be screwed into the G.I. box by means of 3.3 mm dia rounded screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shap as per standard drawing. (DSR Civil-2014 item no. 10.18) |
| 162 | Sub-Head : LIGHT & FAN FIXTURELED Batten light (System lumen efficacy ≥120 <135 lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED,Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), DCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast / Extruded aluminium Body (Thickness≥ 1.20 mm) 18- 22 watt (DSR-25EM No. 8.10.1) |
| 163 | Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal( Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, suitable for operation with regulator for speed control and all remaining accessoriesincluding safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum) (DSR-25EM No. 9.2.3) |
| 164 | Supply of AC 200mm Sweep, 230/250 Volts, 50 Hz exhaust fan (Light Duty) with blades,cover etc. complete as required (As per A.R.) |
| 165 | Supply of Factory made 12 to 20 Watt LED Bulb fitting,cool day light,(65000 K temp.) suitable for Batton/Angle holder including making connection.Complete in all respect. (As per A.R.) |
| 166 | Supply of recess mounting round 12 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect.CAT-AAA |
| 167 | Supply and fixing of SINGLE phase multifunctional electronic energy meter 10 to 60 Amp. Capacity fitted in intergral box on wall complete in all respect. (As per A.R.) |
| 168 | Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge ,complete in all respect including excavation and refilling.The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 35 sq. mm 3-1/2 core (DSR-25EM No. 20A.1H) |
| 169 | Supply & Erracetion of factory fabricated & wired metal clad dust and vermin proof floor mounting, M.S. Channel Base with bottom and top cable entreis Electrical control panel with TPN MCCB's (Four Pole 36 KA with thermal magnatic release)Switches Complete and instrument chamber etc.complete in all respects. The instrument chamber shall be separate and shall comprise of flush type digital metering system for phase to phase voltage and single phase voltage, current and other parameters(KVA,P.F,KW etc) in each phase with touch type selector switches for different readings, instrument fuses, current transformer etc. The panel board shall have suitable capacity electrolytic alumininum busbars as per IS8623 or above istulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/BMC support with deteachable side covers and shall be suitable for extension on the sides. The MCCB's shall be complete with suitable cable end boxes, compression glands and indicating lamp on incoming etc.The Job includes the grounting of the board as per directions of Engineer-in charge. All out goings of 100 Amp and above shall have an Ammeter. The panel board shall be fabricated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubicle type switch board shall be of cat B Only. Incoming 100 Amp MCCB -1 No Outgoning 63 Amp. MCCB-2 Nos. + 63 Amp. DP MCB-9 Nos (DSR-25EM No. 20.1.1) |
| 170 | C.C. ROAD (45 m), INTERLOCKING PAVER BLOCK (105 sqm), DRAIN 300x450 mm (55 m) & UTILITY SHIFTINGPreparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.1) |
| 171 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications : With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR value-30. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.78.1) |
| 172 | Construction of granular sub-base by providing close graded material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications : With material conforming to Grade-II (size range 53 mm to 0.075 mm) having CBR value-25. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.78.2) |
| 173 | Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub-base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.79) |
| 174 | Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator, vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications. (Panel shuttering work paid separately. Cement content considered @ 330 kg/cum; excess/less cement as per design mix payable/recoverable separately.) - Less deduction for using M-20 grade concrete instead of M-25 grade concrete in C.C. pavement. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.75+16.76) |
| 175 | Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS : 1838 for fibre board and IS : 1834 for hot sealing bitumen compound grade A.). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.45) |
| 176 | Providing and laying factory made chamfered edge cement concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking, using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete : 80 mm thick C.C. paver block of M-35 grade of approved colour, design and pattern. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 16.91.2) |
| 177 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement : 4 coarse sand). Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 13.5.1) |
| 178 | 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement. Rates are exclusive of labour cess and GST and inclusive of all other taxes. (DSR No. 13.9.2) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 27, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender