Tender For Repair/Maintenance To Leakage, Seepage, Sunken Treatment And Roof Treatment At Akash Vihar At Af Station Suratgarh
Tender Value
30 Lakhs
Estimated cost
Bid Submission
17 Nov 2026
7 days left
EMD
60000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganganagar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Maintenance To Leakage, Seepage, Sunken Treatment And Roof Treatment At Akash Vihar At Af Station Suratgarh
BOQ
| Sl. No. | Item Description |
| 1 | BOQ (REPAIR/MAINTENANCE TO LEAKAGE, SEEPAGE, SUNKEN TREATMENT AND ROOF TREATMENT AT AKASH VIHAR AT AF STATION SURATGARH) |
| 2 | Demolition of brick masonry built in cement mortar including all quoins, arches and removing from site etc. complete all as specified and directed. |
| 3 | M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cm 1 : 6 complete all as specified and as directed by Engr-in-Charge. |
| 4 | All as per Ser item No 2 here in before but using old bricks |
| 5 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish from the premises. complete all as specified and as directed. |
| 6 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each and removing from site complete all as specified and direcetd. |
| 7 | Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each and removing from site complete all as specified |
| 8 | M&L Factory made Pressed steel frames of size 105mmx60mm made of 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified. |
| 9 | M&L Factory made Pressed steel frames of size 125mmx60mm made of 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified. |
| 10 | S&F factory made 35mm thick 2nd class HW Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkatsNote: Glass/wire gauge shall be measured and paid for seperately. |
| 11 | S&F Aluminum handles, 150 mm size cast type complete all as specified and directed. |
| 12 | S&F aluminium anodised, barrel tower bolt of extruded section and fixed, 150 mm long (ISI marked), complete all as specified. |
| 13 | S&F butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified. |
| 14 | S&F aluminium alloy, 16mm dia and 250mm long anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, complete all as specified. |
| 15 | S&F 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type back side and one face is covered with decorative face veneer with lipping/frame to match, fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 16 | Factory made single extruded WPC (Wood Polymer omposite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate andnatural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). |
| 17 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt inges and necessary S S screws shall be paid separately) |
| 18 | M&L Granite of thickness not less than 18 mm of any type work(table rubbed and polished) in steps, jambs,pillars windows cill cooking platform and like including pointing in white/colour cement and pigment to match with shade of granite including bull nosing of external,including demolition of stone slab and tiles of any description or thickness complete all as specified and as directed. complete all as specified and directed. |
| 19 | M&L RCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings or in shelves and the like,complete all as specified and as directed. |
| 20 | M & L for formwork to soffits of suspended slabs such as shelves,landings ,cooking slabs and similar work; not exceeding 200mm thick (Horizontal or sloping) flat in fair finished surfaces on concrete ,complete all as specified and as directed. |
| 21 | M & L TMT bars 8 mm dia and over cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 22 | M&L for Plain cement concrete 1:2:4 type B-I (20mm graded stone aggregate) as padding on roof finished, complete all as specified and directed by Engineer-in-Charge |
| 23 | M&L for PCC 1:5:10 type E2 (using 40 mm graded crushed stone aggregate) as in filling of sunken floor etc complete all as specified and directed |
| 24 | M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 , using 40 mm graded crushed stone aggregate as in floor, laid in slope of 1:12 and surface finished even and smooth without using extra cement including making joint at 2.5 m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand). Complete all as specified and directed. |
| 25 | M&L for First quality glazed ceramic coloured tiles of (450x350mm) x 7 mm thick, laid on vertical surfaces of wall such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles with & including dismantling of existing tiles of any description ,complete all as specified and directed by the Engineer in Charge. |
| 26 | M&L for First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles,with & including dismantling of existing tiles of any descriptioncomplete all as specified and directed by the Engineer in charge. |
| 27 | Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for key, scrubbing down with water and removing rubbish from the premises etc. complete all as specified and directed. |
| 28 | M&L for 12 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed. |
| 29 | Material and labour for 15 mm thick rendering in cement mortar 1:4 mixed with approved water proofing compound on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement all as specified and directed.Note: Water proofing compound shall be measured and paid separately. |
| 30 | M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces of roof projection/ ceiling and surface finished even and smooth without using extra cement, complete all as specified and directed. |
| 31 | M&L for rough cast plaster with a mixture consisting of crushed stone or fine gravel aggregate of size 6mm to 8mm as directed, mixed with coarse sand, fine sand and cement in the ratio of 1:1:1, finished even rendereing with under coat 15mm thick cement and sand mortar 1:3 complete all as specified and directed |
| 32 | M&L for preparation of new plastered surfaces of wall and applying two coats of oil emulsion distemper over 1.5 mm thick JK/Birla wall care putty to achieve smooth finish surface, complete all as specified and directed. |
| 33 | M&L for preparation of new plastered surfaces of ceiling and applying two coats of white wash, complete all as specified and directed. |
| 34 | Applying two coats of exterior acrylic emulsion (weather proof treatment ), in plain patterns, over new plastered surfaces , including preparation and using primer,complete all as specified and directed. |
| 35 | M&L for prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 36 | S&F in replacement viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern) and inlcuding flush pipe set of CP jet with PVC pipe of superior quality complete all as specified and directed. |
| 37 | S&F in replacement, PVC valveless, dual type, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float , 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified and directed. |
| 38 | Supply and fixing in replacement, wash hand basin vitreous china flat back 550 x 400 mm size white, first quality, with and including PVC waste coupling 32mm size, PVC waste pipe 32mm bore, brackets of Mild Steel angle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer over angle iron brackets to walls complete all as specified and as directed. |
| 39 | S&F in replacement stainless steel sink with drainage board made of 1.00 mm thick sheet for kitchen or with plugs washers & wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm with bowl size 410mm x330mmx200mm, with and including PVC waste pipe and CP waste coupling 32mm and making good to disturbed surfaces, complete all as specified and directed. |
| 40 | S&F as in replacement 15mm bore Pillar taps cast copper alloy, with capstan head, fancy type, chromium plated, weight not less than 665 gm screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe |
| 41 | S&F in replacement stop/angle valves, 15mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specified and directed. |
| 42 | S&F in replacement Gun-metal, globe or gate valves of 15 mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified. |
| 43 | S&F in replacement PVC connection 15mm dia, 600mm long, hot water grade with brass chromium plated nuts and washers at both ends, complete all as specified. |
| 44 | S&F in replacement Brass chromium plated shower rose of 125mm size with or without swivel joints with arms suitable for 15mm bore pipe, complete all as specified. |
| 45 | S&F in replacement brass chromium plated grating 125mm dia with hole wate, complete all as specified and directed. |
| 46 | S&F as in replacement Rotational moulded plythelene white water storage tank tripple layered white coloured, 1000 litres capacity (cylinderical vertical with cxlosed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm for ball valve brass high pressure, with polythene float and fly nut complete all as specified and directed. |
| 47 | All as per srl item No 44 here in before but tank of capacity 500 litre |
| 48 | M&L for Galvanised iron tubing 15mm bore,medium grade,with all fittings fixed to walls or ceiling or laid in floors, in concealed pipe work including making good the chases etc in cement mortar(1:3) after fixing of pipe,incuding taking down of old rusted/u/s GI pipe removal from site. complete all as specified and directed.(Rates for cutting of chases is included in respective items of taking down).complete all as specified and directed |
| 49 | M&L for Galvanised iron tubing 20mm bore,medium grade,with all fittings fixed to walls or ceiling or laid in floors, in concealed pipe work including making good the chases etc in cement mortar(1:3) after fixing of pipe,incuding taking down of old rusted/u/s GI pipe removal from site, complete all as specified and directed.(Rates for cutting of chases is included in respective items of taking down).complete all as specified and directed |
| 50 | S&F in replacement Long Body Bib taps,15 mm cast copper alloy,chromium plated ,fancy type ,screwed down , screwed for iron pipe , complete all as specified and directed by the Engineer in Charge. |
| 51 | Dismantling for Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified. |
| 52 | S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructionscomplete all as specified and directed. |
| 53 | M & L rolled mild steel as in roof trusses (framed), trussed, purlins and the like fixed with angle cleats and connecting plates Fe410-W (Gde-E-250) quality-A all as specified and directed by Engr-in- charge |
| 54 | Waterproofing membrane:Supplying and applying water-based ,single component UV resistant elastomeric PU liquid membrane coating applied with brush/roller having SRI >109 with an elongation of >400% and tensile strength of 1.4 MPa as per ASTM D 412, 80 % Solid Content, shore A Hardness of min. 50 as per ASTM D 2240. The system includes final base preparation as per note given below, applying Home Sheild PU ELASTOSEAL BTD or approved product in three coats at 1.85 kg per Sqm providing min 1 mm DFT , complete as per Manufacturer specifications along with 45 GSM Fiber mesh sandwiched between 1st and 2nd coat . Waterproofing membrane to be terminated on parapet wall in a V groove of size 25 mm x 25 mm atleast 300 mm above FFL which should be sealed with Polymer Mortar. Additional layer of geotextile membrane for the protection of waterproffing membrane .The application will be executed by company authorised applicator upon verification from the company.Before tratment, repair of roof should be done by contractor as required (CM pointing 1:4 and PCC 1:2:4) |
| 55 | M&L 15 mm thick screed plaster on roof in CM 1:4 using WPC (WPC shall be measured and paid saparately) |
| 56 | M&L APP based polymeric membrane 3mm thick (minimum) weight 3 Kg/Sqm reinforced with polyster non-mover fabric (not less than 150 gm/sqm) laid over a tack coat of bitumen 85/25 @ 1.2 Kg/m2 on surface by forced applicantion. Complete all as specified and directed. |
| 57 | 40 mm thick brick tiles laid on roof and joints grouted floor in cement mortar 1:3 mixed with 5% crude oil by with of cement complete all as specified and directed. |
| 58 | All as per srl item No 54 here in before but using old brick tiles . |
| 59 | Dismantling mild steel work of any driscription and any position complete all as specified. |
| 60 | Supply only Integral waterproofing compound.complete all as specified and directed |
| 61 | S& F in replacement CP concealed stop Cock fancy type/ angle stop cock screwed both end for iron pipe 15 mm bore. |
| 62 | S&F in replacement PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in floor , Type 'B', ISI marked of 110mm bore. complete all as specified and directed |
| 63 | S& F as in replacement PVC (SWR) bend with access door of any radius of 110mm bore. complete all as specified and directed |
| 64 | Taking down existing water proofing treatment from the top of RCC/arch slab, including taking down existing PCC padding tiles and brick tile mud phuska or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish outside the MOD land , complete all as specified and directed. |
| 65 | Dismantling of RCC Over Head water tanks of any capacity and removing garbage from site Complete all as specified and directed. |
| 66 | Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for (Reinforcement cut as required to facilitate demolition) and removing rubbish from the site , complete all as specified. |
| 67 | M&L for applying for Dr. Fixit bathseal system over the sunken portion floor of bathroom, with the products in the \\"Kit' as Dr. Fixit bathseal 2K WPC - Acrylic elastomeric cementitious waterproof coating for sunken portion Floor and walls in bathroom complete all as specified and directed. |
| 68 | M&L for galvanized iron spout pipe 40mm dia projecting atleast 20cm clear of wall ‘medium grade’ including making holes in walls & making good disturbed surfaces, complete all as specified & directed. |
| 69 | M &L for chipping of spalled and loose concrete and cleaning rust from reinforcement by sand blasting, scrubbing down concrete surface with wire brushes, cleaning with water alloy to dry and applying a layer of zinc rich epoxy primer as in anti rust on all exposed reinforcement followed by a layer of binding coat of epoxy adhesive on complete exposed surface of concrete to be gunitd and aplying a two layer of guinting over steel welded mesh 2mm dia. of wire and aperture 75mm. Total thickness of guinting n exc. 40mm as per manufacure instruction and finally applying cement plaster over guinting surface of required thk to give even surface as in side , soffits to slab, chajjas, facia,parapets,lintels,columns,and beams,complete including necessary scrafolding, shuttering, chasing to brick work or Rcc members at any height upto 6 storied building incuiding removal of all small trees /shrubs etc., completed all as specfied and as directed . |
| 70 | M&L for applying coating of DR.Fixit on plastered surface after complete removal of existing treatment as per manufacturer instruction all as directed by Engr-in-Charge. |
| 71 | Use and waste of formwork to cornices and mouldings of any shape in cross section and any girth in fair finished surfaces of concrete complete all as specifed and directed. |
| 72 | Use and waste of formwork to edges of concrete flats, treads breaks in floor, window cills, concrete railing, openings in concrete walls, floor and roofs and similar works exc 5cm but not exc 10cm wide rough finish surface of concrete, complete all as specifed and directed. |
| 73 | Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary of tender documents. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 17, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender