Tender For Comprehensive Repair/Maintenance To Certain Buildings In Otm Area Under Ge (Af) Adm Area At Af Stn Gwalior
Tender Value
55 Lakhs
Estimated cost
Bid Submission
23 Nov 2026
26 days left
EMD
1.07 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gwalior → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Comprehensive Repair/Maintenance To Certain Buildings In Otm Area Under Ge (Af) Adm Area At Af Stn Gwalior
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc complete all as specified and directed. |
| 2 | M&L for brick work with subclass B bricks old size straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 3 | Taking down cement plaster on brick or stone wall etc incl racking out joints hacking for key & scrubbing down with water etc. and removal of material out of MD land complete all as specified . |
| 4 | M & L for 10mm thick rady mix plaster on brick wall, concrete surface finished even and smooth without using extra cement complete all as specified and directed |
| 5 | M & L for 15mm thick rady mix plaster on brick wall, concrete surface with finished even and smooth without using extra cement complete all as specified and directed |
| 6 | M & L for 5mm thick rady mix plaster on ceiling /facia/roof projection and finishing even and smooth without using extra cement complete all as specified and directed. |
| 7 | M&L for preparing new plaster surfaces of ceilings and applying three coats of white wash complete all as specified and directed. |
| 8 | M&L for preparation of old ceiling surface and applying one coat of white wash complete all as specified and directed. |
| 9 | M&L for preparing new/old plaster surfaces of Walls and applying two coats of Oil Emulsion over a coat of primer complete all as specified and directed. |
| 10 | M&L for preparing new/old plaster surfaces of Walls and applying 3mm thick wall care putty complete all as specified and directed. |
| 11 | M&L for preparation of old wall surface and applying one coat of oil Emulsion paint complete all as specified and directed. |
| 12 | M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over new/old plaster surfaces of walls complete all as specified and directed. |
| 13 | M&L for prepration of existing treatment and applying one coat of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1 litre /10sqm over old surfaces of walls complete all as specified and directed. |
| 14 | Taking down chowkat or frames with shutter (without taking off shutters from the frames) n.exc 1.5 Sqm including iron mongery each complete all as specified and directed. |
| 15 | Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including iron mongery and cutting holes for hold fasts & making good complete all as specified & directed. |
| 16 | Taking down shutters of any description area exc 1 Sqm and n.exc 2Sqm each,complete all as specified and directed. |
| 17 | Refixing of shutters of any description exceeding 1 sqm but not exceeding 2 sqm each in same or other opening(s) after resecuring or easing & adjusting, including taking down shutter from chowkat or frame complete all as specified and directed. |
| 18 | S&F for Factory Made Solid extruded wood polymer composite solid door/window/ceosetory window & other frame chowkhat of sie 65x125 mm comprising of virgin polymer of k value 58-60,calcium carbonate and natural fibres and non toxic additives fabricated with miter joints after applying pvc solvent and screwed with full body threaded star headed ss screws having minimum frame density of 750kg/cum,screw withdrawl strength of 2200 N and 1100N,minimum compressive strength 58 N/mm2,modules of resistance 900N/mm2 & resistance to & fixing in position with holdfast /lugs/ fasterners of reuired depth as per directions of engineer-in-charge complete all as speciifed and directed. |
| 19 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. |
| 20 | S&F 30mm thick FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company, Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.The wire gauge shall be stretched to tighten firmly complete all as specified. |
| 21 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid forseparately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. |
| 22 | S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. |
| 23 | S & F factory made UPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Note :- Net Opening will be measured lor payment purpose. |
| 24 | S&F Powder Coated (minimum thickness of powder coating 50 micron Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 25 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/Wiremesh, C.P. brass/ stainless steel screws, all complete as per directions of EIC. |
| 26 | M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of EIC. |
| 27 | M&L Anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern,with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre,including cutting the grill to proper opening size for fixing and operation of hadles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engneer-in-charge |
| 28 | M&L for 3mm thick figured or pin head glass ordinary quality and glazing with oil putty/beadings for aluminium frame in square n exc 0.5 sqm in each pane complete all as directed by Engineer-in-Charge |
| 29 | Supply only 5mm thick glass as approved by GE |
| 30 | S & F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides,both face is covered with decorative face veneer with lipping/frame to match complete all as specified and directed. |
| 31 | S & F 35 mm thick 2nd class hard wood glazed skeleton shutters factory made open rebated and prepared to recieve glass, guazed etc ( with sash bar ) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part 1 , Section 8 , clause 8.24 (a) and fitted to chowkhat complete all as specified. |
| 32 | M&L two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces on new wooden surfaces of any description not otherwise described over 10 cm width or girth. |
| 33 | M&L one coat of synthetic enamel paint over old painted surface of wood work of any description over 10 cm width or girth including preparation of old surfaces complete all as specified and directed. |
| 34 | S & F in repair 18mm thick PVC board of grade 1 quality of both side plain white colour fixed with screws, solvent cement/adhesive to make kitchen cabinet sides top and bottom, shelves inside the cabinet and shutter or drawer including dismantling of existing board any type or specification complete all as specified and directed. |
| 35 | Complete all as per ser Item No 34 above but one side prelaminated type |
| 36 | Complete all as per ser Item No 34 above but 12mm thick both side plain type |
| 37 | S & F continuous (Piono) hinges ,stainless steel bright finished or electrogalvanised, width of flap 30 mm (when open), complete all as specified and directed. |
| 38 | S&F 125 mm size stainless steel, Hasp and staple, safety type, steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed. |
| 39 | S&F stainless steel handles of 100 mm size for Cup board complete all as specified. |
| 40 | S&F stainless steel magnet catchers for the cupboards/cabinate (including necessary fixing arrangement) |
| 41 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed . |
| 42 | S&F for mild steel framed/unframed work such as grills, grating etc with ends of bars shouldered and or riveted into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, cooler platform, frame work of water tanks and similar work including welding conforming to Fe-290 & grade E-165 etc complete all specified and directed |
| 43 | Material & Labour for providing and fixing stainless steel (Grade 304) grill/railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab or window jambs with suitable arrangement complete all as specified and directed . |
| 44 | S& F Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required:hooks (stay), heavy, for largegates; hook and pintle hinges:large hasps and staples; chains;hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to woodtrusses or rafters; knee piece inserts; two way and three way straps, plate washers and similarsmall articles conforming to Fe-290 Gde-E-165 etc complete all specified and directed |
| 45 | M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws to hangar roof at 12 to 20mtr height including Dismentling of existing plain or corrugated steel/AC complete all as specified and directed. |
| 46 | M&L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, Ridge, valley/ gutter fixed with self tapping screws to hangar roof at 12 to 20mtr height including Dismentling of existing Plain or corrugated steel /AC Sheet complete all as specified and directed. |
| 47 | M&L for PCC 1:2:4 type B-1 (using 12.5 mm graded stone aggregate) as in posts, holdfasts including necessary formwork as per site requirement complete all as specified and directed |
| 48 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks, or galvanised wire staples.complete all as specified and directed. |
| 49 | S & F 4mm thick Sheet glass, ordinary quality in square in not exc 0.5 sq.m in each pane complete all as specified and directed. |
| 50 | Hacking out old broken glass panes from steel/Aluminium frame including putty/ metal beadings and supply and fix sheet glass ordinary 3 mm thick, in squares n.exc. 0.50 Sqm in each pane including necessary arrangement new oil putty or with existing metal beadings (up to third floor) complete all as specified and as directed |
| 51 | Hacking out old broken glass panes from wooden framed shutters including putty/wooden beadings and supply and fix sheet glass ordinary quality, 3 mm thick, in square n.exc. 0.5 Sqm in each pane including necessary arrangement oil putty/wooden/metal beads complete all as specified and as directed. |
| 52 | M&L for 3mm thick figured or pin head glass ordinary quality and glazing with oil putty/beadings in square n exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size quantity or description) from wooden frame/Steel frame (up to third floor) complete all as directed by Engineer-in-Charge |
| 53 | S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanized wire staples etc. in wooden door / window and Steel door / window, completed all as specified and directed. |
| 54 | S&F stainless steel hinges medium weight butt hinges of 100 mm size complete all as specified and directed. |
| 55 | S&F Stainless Steel handle 150 mm size complete all as specified and directed. |
| 56 | S&F stainless steel barrel tower bolts of extruded section and fixed 150mm long complete all as specified and directed. |
| 57 | S&F stainless Steel barrel tower bolts fixed 100mm long complete all as specified and directed. |
| 58 | S&F 250mm long Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Stainless Steel and fixed |
| 59 | S&F of Capsule door closer of size 300mm in wooden/steel frame by welding or screwing as which ever is appropriate for fixing in frame complete all as specified and directed. |
| 60 | S&F for 140mm Floor door stopper of Stainless Steel body and tongue, anodised, with hard drawn steel spring over all complete as specified and directed. |
| 61 | S&F in repair stainless steel hinges medium weight butt hinges of 100 mm size complete all as specified and directed. |
| 62 | S&F in repair Stainless Steel handle 150 mm size complete all as specified and directed. |
| 63 | S&F in repair stainless steel barrel tower bolts of extruded section and fixed 150mm long complete all as specified and directed. |
| 64 | S&F in repair stainless Steel barrel tower bolts fixed 100mm long complete all as specified and directed. |
| 65 | S&F in repair 250mm long Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Stainless Steel and fixed |
| 66 | S&F in repair Capsule door closer of size 300/250mm in wooden/steel frame by welding or screwing as which ever is appropriate for fixing in frame complete all as specified and directed. |
| 67 | S&F in repair for 140mm Floor door stopper of Stainless Steel body and tongue, anodised, with hard drawn steel spring over all complete as specified and directed. |
| 68 | S&F in repair Harrison rails (Heavy duty) mild steel chromium plated (Curtain Hanging Rods) 20 mm dia including brackets, including fixing arrangement,including Finials (End Caps) and making up repair work and all fitting complete all as specified and directed. |
| 69 | S&F in repair, aluminium (extruded section body) door closer hydraulically regulated, designation No. 3 universal type, suitable for door shutters up to 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 70 | S&F in repair double action floor spring hydaulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty including necessary cutting to floor and concrete work complete all as specified and directed. |
| 71 | Taking down existing aluminium doors/windows in any size and in any description with complete fittings and fixture and refixing in the same opening after repairing/servicing/greqasing & adjustment of spring/locking syestem etc complete all as specified and directed.Note: Material like aluminium snap beading, rubber gasket and glass shall be paid separately |
| 72 | Supply only powder coated aluminium snap beading as approved by GE |
| 73 | Supply only rubber gaskete for packing of glass panes as approved by GE |
| 74 | Supply only stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm as approved by GE |
| 75 | Supply only 5mm thick tinted glass as approved by GE |
| 76 | S&F in repairs Mild steel Mortice lock double handle, vertical type, 06 levers for door complete all as spd and directed by Engr in charge. |
| 77 | M&L for 75mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation filling,mass concrete,sub base etc including demolition of existing PCC and removal of demolished material out of MD land complete all as specified and directed. |
| 78 | M&L for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in coping, kersbs,floor leveling leveling to recive the screed/pcc , mud stops rounded or chamfered in edges etc, finish even & fair without using extra cement including demolition of existing PCC and removal of demolished material out of MD land complete all as specified and directed including necessary formwork as per site requirement |
| 79 | M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone agg) as in plinth protection finished even and smooth with using extra cement including demolition of existing PCC and removal of demolished material out of MD land complete all as specified and directed. |
| 80 | M&L glazed colour ceramic coloured tiles 450 x 300 x 7mm/600 x 300 x 7mm thick in vertical surfaces such as skirting dados etc, set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including fixing with neat cement based over 10mm thick plaster cement motar 1:4 including dismentling of existing tiles with CM bedding and removal of material out of MD land complete all as specified . |
| 81 | M&L for coloured non skid ceramic tiles joint free floor tiles 7- 8 mm thick (square/rectangular) area of each tiles exc. 0.06 sqm but not exc. 0.11 sqm, in floors etc including fixing with neat cement over screed bed or bedding layer of mortar 15 mm thick CM 1:6 including dismentling of existing tiles with CM bedding and removal of material out of MD land complete all as specified and directed |
| 82 | M&L for coloured non skid ceramic tiles joint free floor tiles 7- 8 mm thick (square/rectangular) area of each tiles exc. 0.18 sqm but not exc. 0.38 sqm, in floors etc including fixing with neat cement over screed bed or bedding layer of mortar 15 mm thick in CM 1:6 including dismentling of existing tiles with CM bedding and removal of material out of MD land complete all as specified and directed |
| 83 | M&L coloured ceramic tiles joint free non skid coloured ceramic tiles 7- 8 mm thick (square/rectangular) area of each tiles exc. 0.18 sqm but not exc. 0.38 sqm, in skirting etc including fixing with neat cement over dado or bedding layer of mortar 10 mm thick plaster cement motar 1:4 including dismentling of existing tiles with CM bedding and removal of material out of MD land complete all as specified and directed |
| 84 | Demolition of sunken slab floor or WC and Bath including WC trap etc incl taking down loose filling of aggregate in any type and removing where directed out of MD land and providing water proofing treatment of sunken slab in following . (a) 15mm thick rendering on vertical sides of RCC slab in CM 1:3 mixed with WP chemical of Sika/Fosroc/M/s Choksey or equivalent as per manufacturer instructions. (b) Cleaning the concrete surface by brushing and watering and remove all surface inperfections. (c) Fixing 40mm dia Pipe 450mm long bottom of the sunken and wraping of bath seal tape on the pipes inserted through walls to floor are and seal it (Bath seal tape product of Sika/Fosroc/M/s Choksey or equivalent and grouting around the inserted pipes byu porable Sika/Fosroc/M/s Choksey or equivalent bath seal grout as directed. (d) Make angle fillets by mixing sand cement of Sika/Fosroc/M/s Choksey or equivalent on all corners. (e) Brushing neat cement slurry two coats with high performance cementitious polymer water proofing coating of Sika/Fosroc/M/s Choksey or equivalent bath seal WPC of thickness 1mm in combination of WPC and cement (1:1.5) by vol and giving upto height 15cm from bottom slab and allow it dry completely. (f) Providing PCC 1:4:8 type D-2 using 40mm graded stone aggregate mixed with WPC of Sika/Fosroc/M/s Choksey or equivalent as per amnufacturer instructions in sunken slab over brick bat . (g) Fill the sanitary gaps with Sika/Fosroc/M/s Choksey or equivalent sealing compounds complete. |
| 85 | M&L Granite (of any type) work, 20 mm thick (Table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms in cm 1:4 and including pointing in white cement 1:2, using marble dust with admixture of pigment to match with marble shade of Granite including half moulding of granite edges including screed bed 20mm thick in cm 1:6 including dismentling/demolition of existing tiles/stone slab with CM bedding and removal of material out of MD land complete all as specified and directed. |
| 86 | M&L for machine cut Kota stone slab 20 to 25mm thick Mirror polished in treads, landings of stair case over cement screed bed laid and jointed wilth grey cement slurry mixed with pigment to match the shade of the slab lincluding & grinding polishing over and including screed bed 20mm thick in cm 1:6 including demolition of existing tiles/stone slab with CM bedding and removal of material out of MD land complete all as specified and directed. |
| 87 | M & L for machine cut Kota stone slab as in skirting, risers 20 to 25 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with mirror polish granite finish including backing coat 10 mm thick in cm1:3 Incl demolition of existing tiles/stone slab with CM bedding/coating and removal of material out of MD land complete all as specified and directed. complete all as specified and directed. |
| 88 | M & L for Sand filling under floors or in foundations including watering and consolidation etc complete all as specified. |
| 89 | M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with grey cement and pigment laid in floor and joints of interlocking tiles/ paver block to be filled with fine sand and broomed etc including dismentling of existing tiles/stone slab/paver block with CM bedding/coating complete all as specified and directed. |
| 90 | Dismantling existing sunken interlocking pavers block of any description, size and pattern and refixing the same in any location for proper matching with existing surface after carrying out the necessary repair to the under layer complete all as specified and directed. Note:- Sand cushioning and sub base concrete will be measured and paid separetely. |
| 91 | M&L for chequred tiles of approved design,colour & of ( size 300mmx300mmx25mm) set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles & includind 20 mm thick screed bed or bedding layer in CM (1:4) including demolition of existing tiles/stone slab/paver block with CM bedding/coating and removal of material out of MD land complete all as specified and directed. |
| 92 | M&L Precast cement concrete 1:3:6 type C1 (Using 20mm graded stone aggregate) for Kerb stone (Factory made) of size 20cm x10cmx30cm and set in cement mortar 1:4 (1 cement: 4 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required, including demolition of existing tiles/stone slab/paver block/Kerb stone with CM bedding/coating and removal of material out of MD land complete all as specified and directed. |
| 93 | M&L formwork to chullah hoods, chajjas, trough and similar itmes including edges complete all as specified and directed. |
| 94 | Mild steel TMT bars 10mm dia and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. complete all as specified and directed |
| 95 | M&L reinforced Cement concrete (1:2:4) type B-1, ( 20 mm graded aggregate ) as in chajjas/roof projection/Rcc railing repairs as in similar wk including demolition of existing RCC and removal of material out of MD land complete all as specified and directed. |
| 96 | M&L for precast reinforced concrete 1:2:4 type B1 using 20 mm graded stone aggregate for drain cover slab set in and pointed in CM 1:6 including necessary formwork including demolition of existing RCC cover slab and removal of material out of MD land complete all as specified and directed. |
| 97 | Demolition of cement concrete (unreinforced) in Roofs, floors (other than ground floors), tiles including any type of existing roof treatment and removing outside MOD land complete all as specified and directed. |
| 98 | M&L for screed bed 10mm thick cm 1:4 on fair face of concrete surface with mixing WPC @ 200 ml per bag of cement finished even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured & paid separately under respective item of BOQ. |
| 99 | M&L for hybrid (acrylic+polyurethane) based waterproofing flexible liquid applied membrane single component, three coat system reinforced with fibre mesh having crack bridging upto 2mm and elongation upto 200% and Dry film thickness DFT 1000 microns with heat reflective system for all types of exposed roof slabs (new and old) terraces (sloped and flat) complete all as spd and directed by Engg-in-charge Note :- Preparation of surfaces incl application and quantity to be applied per coat, will be all as per manufacturer's instructions of the approved makeMake :- Dr Fixit Roofseal Classic/Sika Cool Coat/Asian Paint smart care PU magnum |
| 100 | Supply only Liquid water proofing compound |
| 101 | Disconnecting existing tanks of capacity exc 250 litre but n. exc 500 litre for repair work and refixing the same after repair work is over complete all as specified and directed . |
| 102 | Disconnecting existing tanks of capacity of tank exc 500 litres and n. exc 1000 litres for repair work and refixing the same after repair work is over complete all as specified and directed . |
| 103 | Dismantling posts or struts (wood, steel or R.C.C.) any section, embedded in Concrete, brick work, masonry, etc. including taking out embedded portion and making good disturbed ground, complete all as specified and directed. |
| 104 | M&L Cement concrete type B1 1:2:4 (20mm graded aggregate ) as in foundation/bed block for Posts and Struts incl formwork all as specified and as directed. |
| 105 | S&F,mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc, flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, running bars, for chain link fencing including embeding in concrete and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed |
| 106 | M&L, two coats of synthetic enamelled paint over a coat of red oxide primer including preparation of new steel/iron surfaces exceeding 10cm width or girth.complete all as specified and directed |
| 107 | M&L one coat of synthetic enamel paint over old painted surface of steel work of any description over 10 cm width or girth including preparation of old surfaces complete all as specified and directed. |
| 108 | Supply only MS screw, bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30cm long and dia of neck n.exc 12mm, complete all as specified and directed |
| 109 | Supply only galvanised chain link MS Galvanised fencing any size or type as approved by Engr-in -charge etc, complete all as specified and directed. |
| 110 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc including provision of binding wire including dismentling existing fencing wire mesh/barbed wire any type complete all as specified and directed. |
| 111 | S&F in repair 600 mmx450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC buildg board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers complete all as specified and directed. |
| 112 | S & F in repair Brass chromium plated, tubular towel rails 20 mm dia, D- type, 60 cm long between flanges, completed all as specified and directed. |
| 113 | S&F in repair brass chromium plated shower roses with swivel joints, 125 mm size in square with CP long shank arm including fixing to steel pipe or union, complete all as specified and as directed. |
| 114 | M&L in repair 75mm PVC (SWR)floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 115 | M&L in repair PVC(SWR) gully trap 125/110mm setting and jointing with solvent cement complete all as specified directed. |
| 116 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action with inlet ball valve and float including flush pipe, handle, bracket PVC short/long bendetc. complete all as specified and directed |
| 117 | S&F in repair Vitreous China wash basin, flat back, size 450x300mm white, including waste pipe excluding taps, chain and plug and porcelain stopper but including brackets. |
| 118 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) 'P' or 'S' trap complete all as specifed and as directed. |
| 119 | S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, antisyphonage pipe incl PCC 1:5:10 type E2 in filling making good to floor etc all as specified. |
| 120 | S&F in repair urinal flat back size of 375X390X590 mm white (minimum) with grating and union for discharge pipe including flush pipe and waste pipe (excluding flushing cistern) complete all as specified and directed . |
| 121 | S&F in repairs plastic water closet seat cover, White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specifed and as directed. |
| 122 | S&F in repair angle cock fancy type CP with long shank cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends of size 15mm bore. complete all as specified and directed. |
| 123 | S&F in repairs bib tap, cast copper alloy with capstan head, CP fancy type with long body shank, screwed down with high pressure screwed for iron pipe & fixed 15mm bore, complete all as specified and directed. |
| 124 | S&F in repair Pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 125 | S&F in repair PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified and as directed. |
| 126 | S&F in repairs PTMT/PVC waste pipe 32 mm bore of length up to 80 cm for WHB / sink/unrinal pots, complete all as specified and directed. |
| 127 | S&F in repair 125mm chromium plated central hole grating dome with waste hole complete all as specified and directed. |
| 128 | S&F in repair CP soap dish with glass Finish (Glossy) complete all as specified and directed. |
| 129 | S&Fixed in repair of SS powder coated peg sets of 6 Nos peg set of good quality, complete all as specified and directed. |
| 130 | S&F in repair Brass chromium plated health faucets with flexible pipe length not less than 1.00 mtr (minimum) fixed for EWC/IWC suitable for 15mm bore pipe complete as directed. |
| 131 | S&F in repair fancy type brass chromium plated wall mixer 2-in-1 with wall flanges Connecting legs and bend screwed down suitable for 15 mm bore GI pipe Quarter turn with water saving nozzle complete all as specified and directed. |
| 132 | S&F in repairs of fancy type Centre hole basin mixer brass chromium plated screwed down 15mm bore Quarter turn with water saving nozzle complete all as specified and as directed. |
| 133 | S&F in repairs of fancy type zet sprey stainless steel hose length 1.5-meter long tube Including bracket holder complete all as specified and as directed. |
| 134 | S&F in repairs of urinal spreader brass cromium plated complete all as specified and as directed. |
| 135 | S&F PVC T-base for water tank of capacity 500ltr (Dimensions :870mm dia, leg ht-80mm) including demolition of existing staging and making good with cement mortar complete all as specified and directed Make :- vectus or equivalent as approved by GE. |
| 136 | S&F PVC T-base for water tank of capacity 1000ltr (Dimensions :1090 mm dia, leg ht-165mm) including demolition of existing staging and making good with cement mortar complete all as specified and directed Make :- vectus or equivalent as approved by GE. |
| 137 | S&F rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including over flow 450mm, waste pipe 600mm long with fitting etc. of 20 mm dia incl dismantling of existing tank directed complete all as specified and as directed. |
| 138 | S&F rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including over flow 450mm, waste pipe 600mm long with fitting etc. of 20 mm dia incl dismantling of existing tank directed complete all as specified and as directed. |
| 139 | M&L for cleaning of overhead tank of any description and in position, removing all scale and dirt by detergent/detergent powder and finally disinfected with bleach wash etc from tanks and mouths of circulating pipes etc and writing the date of cleaning and the due date of cleaning, capacity of tanks exc. 250 litres and not exc. 500 litres complete all as specified and as directed. |
| 140 | All as per item No. 139 above but exc 500 & n.exc. 1000 ltrs capacity, complete all as specified and as directed. |
| 141 | S&F in repairs tank covers (with locking arrangements as per existing one) of water storage tank for capacity 500 ltrs to 1000 ltrs complete all as specified & directed. |
| 142 | Cutting chases, pinning in, stone concrete block or slabs wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth and removal of debris otside of MOD land complete all as specified. |
| 143 | S & F of CPVC pipes 25mm all SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of pipe of 20 mm GI pipe complete all as specified. |
| 144 | S&F of 25 mm dia CPVC brass elbow complete all as specified and as directed. |
| 145 | S&F of 25 mm dia CPVC Brass Tee complete all as specified and as directed. |
| 146 | S&F of 25 mm dia female/male brass threaded adapter complete all as specified and as directed. |
| 147 | S & F of CPVC pipes 20mm all SDR 11 Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of pipe of 15 mm GI pipe complete all as specified. |
| 148 | S&F of 20 mm dia CPVC brass elbow complete all as specified and as directed. |
| 149 | S&F of 20 mm dia CPVC Brass Tee complete all as specified and as directed. |
| 150 | S&F of 20 mm dia female/male brass threaded adapter complete all as specified and as directed. |
| 151 | S&F 25 mm internal bore Ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm-210gms) complete, fixed in repairs, all as specified. |
| 152 | Dismantling of cast iron or renforced drain pipe/pvc/AC 100mm/75mm dia of any description complete all as specified and directed. |
| 153 | S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 154 | S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed in floor or trenches complete all as specified and directed. |
| 155 | S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 156 | S&F PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints laid in floors/trenches complete all as specified and as directed. |
| 157 | S&F 75 mm PVC (SWR) junction single, (singl T ) (equal or unequal ), ordinary or inverted ( spigot or socket type ) or with paralle oval access doors branches .complete all as specified and directed. |
| 158 | S&F PVC SWR 110 mm bends any radius complete all as specified and directed. |
| 159 | S&F 75 mm PVC (SWR) bends any radius diminishing pieces or tapers (larger bore measured) .complete all as specified and directed. |
| 160 | S&F 110mm PVC (SWR) vent cowl. Complete all as specified and directed. |
| 161 | S&F 110 mm PVC (SWR) P/S Trap (110/110mm bore) complete all as specified and directed. |
| 162 | S&F in repair stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roofs for bore of 100mm complet all as specified and directed. |
| 163 | S&F in repair stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roofs for bore of 75 mm complet all as specified and directed. |
| 164 | M&L for greasing and oiling of rolling shutters (manually operated) including replacement of small parts such as lock, damaged strip, if any, straightening of guide channel and other small articles to making it functional complete all as specified and directed. |
| 165 | M&L for greasing and oiling of rolling shutters (Gear box operated) including replacement of small parts such as lock, damaged strip, if any, straightening of guide channel and other small articles to making it functional complete all as specified and directed. |
| 166 | M&L for removing/cutting trees, vegetation, digging out roots from concrete or brick wall, filling holes on building (block of 4/6 qtrs) wall/roof/chhajja/water tank staging area etc and making good with cement mortar 1:4 complete all as specified and directed. |
| 167 | M&L False ceiling with GI snap grid frame work of size 595mmx595mm in true horizontal level suspended on interlocking metal grid of hot dipped galvanised steel sections (glavazized @ 170gms/sqm and bottom exposed width prefinished with leaked polyster paint) consisting of main 'T' runners with suitably spaced joints to get required length and of size 38x24x0.3mm spaced at 1200mm centre to centre and cross 'T' of size 24x25x3mm 1200mm long spaced between main 'T' at 600mm center to centre to form a grid of 1200x600mm and secondary cross 'T' of length 600mm and size 24x25x.3mm to be interlocked at middle of the 1200x600mm panel to form grid of 600mmx600mm and wall angle of size 21x21x.3 and laying false ceiling tiles of 4mm thick fiber cement buidling board,white colour desinger type ready to fix non asbestos (minimum weight 4.8kg/sqm) fixed or laid/inserted to GI form work with screws/clips for false ceiling work including, wherever required, cutting/making, opening for services like diffusers, frills, light fittings, fixtures and smoke detectors etc. Main 'T' runners shall be suspended from ceiling using GI slotted cleats of size 25x35x1.6mm fixed to ceiling with 6mm dia and 50m long metal dash fastner, 4mm GI rods with galvanised steel leveling clips spaced at 1200mm centre to centre along main 'T' section (false ceiling system shall be capable to bear distributed load of minimum 15kg/sqm) incl dismantling of old celing board with grid complete all as specified and directed. |
| 168 | Repair leakage of Bib tap/ Pillar tap/ stop cock/Wall Mixer/WHB Mixer/Sink Mixer all bathroom/toilet sanitary/plumbing fittings by replacing of necessary brass spindles/washers/nuts complete all as specified and directed. |
| 169 | Repair/refixing of wooden,aluminium,iron doors/windows by replacing of necessary joinery fitting/raparing items complete all as specified and directed. Please Enable Macros to View BoQ information |
| 170 | Repair/refixing of wooden,aluminium,iron doors/windows by replacing of necessary joinery fitting/raparing items complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysNov 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 33 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender