Tender For Special Repair To Building No P-190 At Mil Stn Abohar
Tender Value
73.76 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
17 days left
EMD
1.35 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Fazilka → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Building No P-190 At Mil Stn Abohar
BOQ
| Sl. No. | Item Description |
| 1 | M & L for removing of existing roof treatment of any type any thickness upto RCC roof slab including mud fuska,demolition of brick tile or pedding etc and removal of demolation material out of defence land complete all as specified |
| 2 | M&L for levelling course for roof slab, Type B0, 1:2:4 (12.5 mm graded aggregate) using waterproofing compound (SBR) for maintaining proper roof slope and finishing cement concrete surface even and smooth without using extra cement complete all as specified. (Minimum thickness of concrete should not be less than 50mm at any point)Note: Waterproofing compound should be measured and paid separately. |
| 3 | M & L rendering/screed 10mm thick water proofing plaster in CM 1:3 on roof slab including mixing of liquid WPC in mortar @ 2% per Kg of cement and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. |
| 4 | Supply only SBR waterproofing compound @ 2% of per kg cement used complete all as speccified.Make : Fosroc/Sika/Choksey/Bostik/STP/Asian Paints/Berger Paints |
| 5 | OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm.(a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification.(b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger PaintsNote : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE.(iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years. |
| 6 | Dismantling of brick work of any type built in cement mortor etc complete all as specified and directed by Engineer-in-Charge |
| 7 | M&L for Old size burnt clay Brickwork with sub class 'B' straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 8 | M & L for brick work in half brick thick wall using using Old size burnt clay bricks straight or curved on plan to any radius built in cement mortar (1:4) complete all as specified and directed by Engineer-in-Charge. |
| 9 | M & L for rendering 15 mm thick on brick work or concrete surface in CM 1:4 finishing even and smooth without using extra cement, all as specified and directed by Engr- in- charge. |
| 10 | Taking down cement plaster/grit plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and directed. |
| 11 | M & L for rendering 15 mm thick on brick work or concrete surface in CM 1:6 finishing even and smooth without using extra cement, all as specified and directed by Engr- in- charge. |
| 12 | M & L for rendering 10 mm thick on brick work or concrete surface in CM 1:3 finishing even and smooth without using extra cement, all as specified and directed by Engr- in- charge. |
| 13 | M & L Washed stone grit plaster on exterior walls in two layers under layer 12 mm cement plaster 1:4 (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per sqm, top layer 15 mm cement plaster 1:1/2:2 (1 cement :1/2 coarse sand 2 : stone chipping 10 mm normal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to be expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately). |
| 14 | M & L for Forming groove of uniform size 12 mm wide and 15 mm deep in the top layer of washed stone grit plaster as per approved pattern using aluminium channel size 12X15X0.50 MM thick, nailed to the under layer and finishing the groove complete as per specification and direction of the Engineer-in-Charge. |
| 15 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats after preparation to the new plastered surfaces complete all as specified and as directed by Engineer-in-charge |
| 16 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-charge |
| 17 | M & L for Shotcreting 25MM thick in RCC columns, beams and slabs and Chajja etc in layers with approved design mix (minimum cement content of 350 Kg/Cum on M-25) concrete having the specified minimum characterristic compressive strength (with ordinary protland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria) including the cost of certering and shuttering at edges and corners etc as directed by Engineer-in-Charge including Chipping of unsound /weak concrete material 25 mm average thickness with mannual chisel and /or standred power driven percussion cavities including cleaning the exposed concrete surface and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc. including removal of rust by applying approved rust removal chemical & the coating with Dr Fixit epoxy zinc primer@ 6sqm/ltr at DFT of 100microns as per specifications and disposal of debries for all lead and lifts all complete as per direction of Engineer-in-Charge.Including the following items as under :-(a) S&F Hard drawn steel wire fabric minimum 2.50Kg/Sqm cut to lengths, bent to shape required and tying with and including nails and mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt all as specified & directed by Engineer-in-Charge.(b) M&L rendering 10 mm thick in cement mortar 1:3 on fair faces of concrete surfaces of ceiling finishing even and smooth without using extra cement.(c) M&L preparation of newly plastered surfaces of ceiling and applying three coats of Distempering with 1st quality acrylic distemper on ceiling. Make : Dr Fixit or equivalent |
| 18 | M & L for Preparation of new plastered surfaces and applying acrylic wall care putty in internal/external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony/ceilings etc (thickness vary from 1.5 to 2.0 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/exterior painting complete all as specified and directed.Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order. |
| 19 | M&L for Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats after preparation to the old decorated plastered surfaces of wall/ceiling complete all as specified and as directed by Engineer-in-charge |
| 20 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm after preparation to the old decorated surfaces complete all as specified and as directed by Engineer-in-charge |
| 21 | M & L for water proofing treatment to RCC sunken slab and adjoining vertical slab as described following any one method Method 1 (A) - Supplying and applying two component elastomeric acrylic polymer modified cementitious waterproofing coating, SmartCare Damp Block 2K or approved equivalent , having 100 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5.Clean all working surface & made free from dirt, grease laitance etc. After inspection for all working area rough surface, cracks & construction joint are treated by polymer modified mortar of 1:1:4 (1 Cement : 1Polymer : 4 Sand).Making Gola of size 75X75mm at junction of vertical & horizontal with the polymer modified mortar of 1:1:4 . (1 Cement : 1Polymer : 4 Sand). The coating shall be terminated at 1600mm in toilet/2100mm in bathroom on vertical walls. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing and shall have consumption of 1.5kg/sqm per coats, etc., complete as per manufacturers specifications. (B) Bore Packing: All the borehole gaps between concrete surface and pvc pipe of various dia upto the neck level shall be filled with non-shrink free flow grout - SmartCare GP Grout or approved equivalent having dual shrinkage compensation property. Before the bore packing, surface of the pvc pipe and concrete surface will be made rough and sand will be sprinkled with polymer bonding agent. (c) Apply 12-15mm 1:3 cement plaster on slab and vertical surface admixed with SmartCare Vitalia Neo @200ml per bag of cement Method 2 (A) Providing & applying two component cementitious & acrylic flexible waterproofing & protective coating, two coats with 1mm DFT, having Hydrostatic (positive) water pressure resistance (DIN 1048) is 7. Abrasion resistance, cm/km is 0.09 of Dr Fixit Pidifin 2k @ 1.5kg/sqm or equivalent with a paint brush over existing roof surface. The Polyester reinforced coated net of 45g/m2, 2.5mmx2.5mm is Laying on the surface immediately on the first coat of two component modified polymer Dr Fixit pidifin 2k or equivalent. After removal of all loose materials like dust etc. With wire brush coir brushes from roof surface to get absolutely cleaned surface free of foreign contaminant filling of crack and patches with polymer based repair mortar/micro concrete, repairing with 15 mm thick cement plaster after the repairing work making the gola on surrounding wall’s junction and seal the vertical walls up to 2100 mm. In case of core cutting on the surface, the joint is seal with non-shrink grout. The work complete as per the direction of Engineer-in-Charge. (Work shall be executed through specialized agency) (B) Apply 12-15mm 1:3 cement plaster on slab and vertical surface admixed with SmartCare Vitalia Neo @200ml per bag of cement Note: (i) The treatment shall be carried out as per the manufacturers instructions and as directed by the Engineer in charge. The name of firm shall be got approved from CWE before carrying out the work. (ii) PCC filling under sunken area will be measured & paid separately Make:- Fosroc/Sika/STP or equivalent |
| 22 | M & L for Providing plain cement concrete Type E-2, 1:5:10 (40 mm graded stone aggregate as in foundation, filling and mass concrete) complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for 25mm thick PCC 1:2:4 type 'B-0' using 12.5 mm graded crushed stone aggregate with a slope of 1:40 complete all as specified and directed by Engineer - in - Charge. |
| 24 | Demolition of cement concrete is reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer in Charge (reinforcement cut as required to facilitate demolition) |
| 25 | M&L Reinforcement cement concrete type B1 1:2:4 using 20mm aggregate as in slab supported on walls beams and columns in floor, roof, landing and as in shelves, Manhole covers, chajja, bands, beams, lintels and similar wks incl necessary formwork/moulding complete all as specified and directed by Engineer-in-Charge |
| 26 | S&F TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less then 0.9 mm dia or securing with clips complete all as specified and directed. |
| 27 | All as per srl item no 26 above but 6 to 8 mm dia. Bar for stirrups |
| 28 | Dismantling of floor, hearth or wall tiling or stone slab laid, bedded & pointed in any mortar including demolition of cement mortar bedding or backing coat, including removal of debries to a distance exc 1.5 km but n.exc 2 Km complete all as specified and directed. |
| 29 | M&L Rendering 10mm thick in CM 1:4 on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing for skirting/dado etc complete all as specified and directed |
| 30 | M&L for Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed |
| 31 | M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 complete all as specified and directed |
| 32 | M&L for Non skid, coloured ceramic tiles 7 to 8 mm thick (Square / rectangular) polished area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed |
| 33 | M&L, Machine cut kota stone slab flooring 18-22mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 34 | M&L, Kota stone slab 18-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 35 | M&L 15 -18mm thick granite stone slab of any type (cut, table rubbed and polished)in steps, jambs, pillars, window cills, cooking platforms and like , bedded & jointed with grey cement slurry & pointing with coloured cement using marble dust with admixture of pigment to match with marble shade; laid over complete all as specified and directed |
| 36 | Taking down steel tubing 15mm bore and connections complete all as specified and directed by Engineer - in - Charge. |
| 37 | Supply & fixing of 20mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed. |
| 38 | Taking down steel tubing 20mm bore and connections complete all as specified and directed by Engineer - in - Charge. |
| 39 | Supply & fixing of 25mm outer dia CPVC pipes SDR 11 including all fittings Plain/brass threaded CPVC SDR 11 fittings (like Elbow, Tee, Socket, Reducer, Union, Bushing, Step over bends, End cap, End Plugs, one side brass/two side brass etc) fixed along walls, ceiling or laying under floors etc and including CPVC solvent cement for jointing complete all as specified and as directed. |
| 40 | S & F in repair Low density polyethylene pipes (LDPE) 32/40 mm of pressure rating 6 kgf/cm2 including bends as required etc fixed complete to walls, ceilings or in floors etc |
| 41 | S&F 15mm size angular Stop valves, cast copper alloy, CP,screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed |
| 42 | S&F 15mm dia size Bib tap cast copper alloy, CP fancy type with capstan head, screwd down , screwed for iron pipes complete |
| 43 | S&F 15 mm bore, swan neck, taps cast copper alloy capaston head CP, screwed down high pressure with or without lettered “ HOT” or “ COLD” with long screwed shanks and fly nuts screwed for iron pipes fixed complete all as specified and directed |
| 44 | S&F 15mm dia two way angle valve brass chromium plated, fancy type complete all as specified and as directed. |
| 45 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed |
| 46 | S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern,), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; flush/waste pipe, and Union for discharge pipe. |
| 47 | S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. Minimum weight 60gms) |
| 48 | S&F vitreous china wash down water closet pan (pedestal pattern) white with CI 'P' or 'S' trap incl water closet seat cover of plastic,jet spray etc.complete incl necessary PVC waste pipe fitting, complete all as specified and directed by Engineer-in-Charge |
| 49 | S&F 10 Litre capacity PVC symphonic action type flushing cistern, duel flush type (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete. |
| 50 | S & F vitreous China squatting pan of Orrissa pattern of approved make of size 580 mm X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl lime concrete bedding and connection to antisyphonage pipe etc including making good to floor complete all as specified and directed by Engineer-in-Charge |
| 51 | S&F PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed |
| 52 | S&F chromium plated soap tray any type and fixed to plugs on wall with chromium plated brass screws complete all as specified and directed by Engineer-in-Charge |
| 53 | S&F in repairs fancy type chromium plated, long shank & cup (concealed type) 15mm bore dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed |
| 54 | S&F in repair brass chromium plated shower rose 100 mm of size with arme and with or without swivel joints to steel pipe or union complete all as specified and directed by Engineer-in-Charge |
| 55 | S&F looking mirror of size 600 x 450 mm, selected quality 5 mm thick including aluminium frame, mounted on 6 mm thick commercial plywood and fixed to wall with wooden plug & chromium plated brass screws complete all as specified and directed |
| 56 | S&F 5mm thick looking mirror of selected quality glass of any size , mounted on 12mm thick commercial plywood incl all around moulding with paint and fixed to teak wood plugs with chromium plated brass screws and cup washers, complete all in repair as specied and directed |
| 57 | S & F Tubular towel rail, 20mm dia, D type, 600mm long between flanges chromium plated complete all as specified and directed |
| 58 | S&F Towel Ring of CP fixed with and including chromium plated brass screws and wooden/ plastic cleats etc complete all as specified and directed by Engineer-in-Charge |
| 59 | S&F in repair vitreous china wash basin, white size 540 mm x 360 mm x 115mm fixed on and including fixing in slab/stone with 32 mm dia brass waste coupling and including wastepipe/ fitting and union complete all as specified and directed by Engineer-in-Charge |
| 60 | S&F in repair 25 mm dia SS Curtain rod, with fixing brackets, stops, rollers etc complete all as specified & directed. |
| 61 | S&F in repair 100 mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed. |
| 62 | S&F in repair 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified & directed. |
| 63 | S&F in repair 125 mm in size aluminium handles cast type anodized complete all as specified & directed. |
| 64 | S&F in repair mild steel sliding door bolt 300 mm long plate type stove enameled black with bright bolt not less than12mm dia. |
| 65 | S & F in repair galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed by Engineer-in-Charge |
| 66 | Dismantling and disconnecting of existing cast iron or reinforced concrete drain pipes, jointed in cement mortar 75/100 mm dia bore fixed to wall,laid in trenches complete all as specified and directed Engineer-in-Charge |
| 67 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets at suitable interval fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant with minimum 100mm separation from wall to pipe complete all as specified and as directed by Engineer-in- charge. |
| 68 | Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 69 | S & F 75 mm bore of pipe uPVC bends of any radius fixed to PVC pipes in reapir complete all as specified and directed by Engineer-in-Charge |
| 70 | S & F 75 mm bore of pipe uPVC bends of any radius fixed to PVC pipes provided with access door in repair complete all as specified and directed by Engineer-in-Charge |
| 71 | S & F 75 mm bore of pipe uPVC junction single,(Single T) equal or unequal fixed to PVC pipes with access door in repair complete all as specified and directed by Engineer-in-Charge |
| 72 | Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls with and including suitable size clamps/brackets at suitable interval of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant with minimum 100mm separation from wall to pipe complete all as specified and as directed by Engineer-in- charge. |
| 73 | Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, laid in trenches, joints fixed with pipe joint lubricant complete all as specified and as directed by Engineer-in- charge. |
| 74 | S & F 110 mm bore of pipe uPVC bends of any radius / shoe fixed to PVC pipes complete all as specified and directed by Engineer-in-Charge |
| 75 | S & F 110 mm bore of pipe uPVC junction single,(Single T) equal or unequal fixed to PVC pipes with access door in repair complete all as specified and directed by Engineer-in-Charge |
| 76 | M&L for 75 mm dia of PVC (SWR) floor trap plain with grating incluing jointing with solvent cement complete all as specified and directed by Engineer-in-Charge |
| 77 | S & F PVC(SWR) Vent cowls 110mm bore all as specified and directed by Engineer - in - Charge. |
| 78 | M&L PCC 1:4:8 type D2 (using 40mm graded aggregate ) in packing under and haunching against the side of pipes of upto110mm dia bore after they are laid and tested |
| 79 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge. |
| 80 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4 Sqm each and removing from site including cutting holes for removal of old rusted hold fast and prepare the surface for new hold fast complete all as specified and as directed by Engineer-in- charge. |
| 81 | Taking down shutter of any description n exc 1.00 sqm each and removal from site complete all as specified and directed by Engineer-in-Charge |
| 82 | Taking down shutter of any description exc 1.00 sqm and n exc 2.00 sqm each and removal from site complete all as specified and directed by Engineer-in-Charge |
| 83 | Taking down shutter of any description exc 1.00 sqm and n exc 2.00 sqm each and Refixing of shutters in same opening after resecuring or easing & adjusting, complete all as specified and directed by Engineer-in-Charge |
| 84 | Supply & fixing factory made UPVC window or ventilator side hung/top hung (glazed and gauge both) made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm) including all fittings like hinges, tower blot, peg stay, locking arrangement etc., making arrangement for fixing of hardware all as per manufacture instruction and refer Drg No BTD-890/R complete all as specified and directed.Note : The unit rate quoted by contractor includes cost of glass & wire mesh (4 mm thick sheet glass ordinary quality plain/tinted for window and 5mm thick frosted glass pin head type for ventilator, wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm) and includes all other connected accessories. Net Opening will be measured for payment purpose.. Provision of all other items as shown on Drgs & Cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be demand to be include. |
| 85 | S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded (Glazed steel window) |
| 86 | S &F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded (wire gauge steel window) |
| 87 | S & F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aparture 1.18 mm and fixed with tinned tacks ro galvanised wire stapple complete all as specified and directed by Engineer-in-Charge |
| 88 | Hacking out old broken glass (any thickness, size quality or description) from wooden / steel / aluminium frame, including punching or drilling out old glazing pins/spring clips complete all as specified & directed. |
| 89 | S&F sheet glass 4 mm thick ordinary quality(plain/floated/frosted/tinted) and glazing with oil putty / wooden beads / aluminium glazing clip in square n.exc. 0.5 sqm in each pane complete all as specified & directed. |
| 90 | S&F sheet glass 4 mm thick ordinary quality (plain/floated/frosted/tinted) and glazing with oil putty / wooden beads / aluminium glazing clip in square exc. 0.5 sqm in each pane complete all as specified & directed. |
| 91 | S&F 200mm, ordinary MS rat tail rod pattern springs including roller and roller plate in repair complete all as specified & directed. |
| 92 | S &F Plain mild steel wire 4mm thick , galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) Please Enable Macros to View BoQ information |
| 93 | S &F Plain mild steel wire 4mm thick , galvanised class 3, in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc. including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender