Tender For Special Repair To Building No P-14 (Qtr No 1 To 8) Or Md Accn At Kheterpal Enclave At Nams
Tender Value
44.17 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
9 days left
EMD
88345
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Amritsar → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Building No P-14 (Qtr No 1 To 8) Or Md Accn At Kheterpal Enclave At Nams
BOQ
| Sl. No. | Item Description |
| 1 | Taking down unserviceable chowkhats or frame with shutters(without taking off shuters from the frames) of any description n. exc 1.50Sqm and removing from site and making good disturbed surfaces of wall in CM 1:3 complete all as specified & directed. |
| 2 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each and removing from site complete and making good disturbed surfaces of wall in CM (1:3) complete all as specified & directed. . |
| 3 | M&L 35mm thick factory made solid PVC (Wood plastic composite ) moulded gauged door shutter with wire mesh 0.18mm nominal dia of wire and average width of apreture 1.40mm in any number of division with brown wood grain texture , including XTN aluminium mesh for additional strength & safety purpose (Confirming as per IS-4020) shall be fixed with 15x15 square tubes in is rails with screwing 8x28mm heat metal Zink coated screws can be remove or fix again after changing of wire mesh when needed . The density shall be as per manufactures instructions complete all as specified and complete all as specified & directed. |
| 4 | S&F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. |
| 5 | S&F factory made solid PVC moulded door shutter with wood free solid board, 28 to 30 mm thick (stiles) with 2, 4 or 6 rised panel design with 5mm thick 3D wood laminated moulded PVC sheet Polyurethane painted on the front and back face with with 19 guage thickness usiing MS square tuning supplying and fixing of 19 mm x 19 mm frame structure and making good complete all as specified and directed. complete all as specified & directed. |
| 6 | S&F Solid PVC Door frame of sizes 95mm x 50 mm made out of 5 mm laminted both side colour PVC sheet reinforcement with MS square tube,supplying & fixing in opening as per specification & drawing complete all as specified and directed |
| 7 | S&F Stainles steel butt hinges 100mm long medium weight fixed complete all as specified and directed |
| 8 | S&F150 mm Aluminium, anodised, barrel tower bolts (ISI Marked) of extruded section and fixed complete all as specified and directed |
| 9 | S&F 150 mm Extruded aluminium alloy handles with base plate, (D type & ISI Marked), anodised complete all as specified and directed |
| 10 | S&F Aluminium door stopper double support with rubber complete all as specified and directed. |
| 11 | S&F 250mm long Aluminium alloy Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed |
| 12 | M&L for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc.(a) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (b) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf.(c) MS Tower bolt 150mm long - 2 No per leaf.(d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf.(e) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf.(f) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf.(g) 12 mm square guard bar, 10 cm centre to centre.(h) 25x4 mm flat iron all around for joint of both frame.(j) One shop coat of red oxide primer and two coats of Synthetic enamel paint to MS window and guard bar.Note:(i) Including taking down old steel window and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge.(ii) sheet glass and wire mesh shall be measured and paid separately) |
| 13 | Material & labour for box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame (single rebated ) of ERW and FI 2mm thick welded /screwed to frame for fixing of sheet glass including fixtures and fittings like a stopper , cleat , pintal hinges , holdfast etc all as shown on drg No CEJZ/TD/1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a) 10mm Sq Guard bar 10cm C/C(b) One shop coat of red oxide and two coats of synthetic enamel paint to MS ventilator and gaurd bar (c) MS Tower bolt 150mm long - 2 No per leaf (d) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf Note:(i) Including taking down old steel ventilator and making good dismantled portion with PCC 1:2:4 type B0 including hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge.(ii) sheet glass and wire mesh shall be measured and paid separately) |
| 14 | S&F GI wire cloth, 0.36 mm nominal dia. of wire and average width of aperture 1.4 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed |
| 15 | S&F Sheet glass, 3mm thick ordinary quality, in squares, not exceeding 0.50 sqm in each pane fix with oil putty complete all as specified and directed. (Note upto four storey height including all scaffolding work ) |
| 16 | S&F in repair for 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane fixed with oil putty or beads and incl hacking out glass old complete all as specified and directed. |
| 17 | S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 18 | M&L for applying one coat of synthetic enamel paint on steel surface of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed. |
| 19 | Taking down cement plaster on brick/stone/concrete walls /ceiling incl racking out joints etc,hacking for key, scrubing down with water etc & dispose off debris upto a distance n exc. 500 mtrs where directed complete all as specified and directed.note -rate applicable upto four storey height incling all scaffolding work |
| 20 | M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces on walls in CM 1:6. finishing even and smooth without using extra cement complete all as specified and directed. |
| 21 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and fair complete all as specified and directed. (WPC shall be measuared seperatly and paid @ 200ML for 50kg cement bags or as per manufacturer's instructions). note -rate applicable upto four storey height incling all scaffolding work Please Enable Macros to View BoQ information |
| 22 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and fair complete all as specified and directed. (WPC shall be measuared seperatly and paid @ 200ML for 50kg cement bags or as per manufacturer's instructions). note -rate applicable upto four storey height incling all scaffolding work Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysNov 17, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender