Tender For Repair / Maintenance To Certain Otm Building Of Fd Regt, Arty Div C And Fd Hosp Under Age B/R-Ii At Itarana Cantt, Alwar.
Tender Value
12 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
8 days left
EMD
24000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Alwar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Repair / Maintenance To Certain Otm Building Of Fd Regt, Arty Div C And Fd Hosp Under Age B/R-Ii At Itarana Cantt, Alwar.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of brickwork built in cement mortar or cement-lime mortar, including quoins and arches, complete all as specified and directed. |
| 2 | Taking down cement plaster on surfaces of any description and in any position, including raking out joints, hacking for key and scrubbing down with water, complete all as specified and directed. |
| 3 | Taking down chowkhats or frames with shutters, without removing shutters from frames, each not exceeding 1.5 sqm, complete all as specified and directed. |
| 4 | Taking down chowkhats with shutters, without removing shutters from frames, each exceeding 1.5 sqm but not exceeding 4 sqm, complete all as specified and directed. |
| 5 | Taking down shutters, each exceeding 1 sqm but not exceeding 2 sqm, and refixing in the same opening after easing, adjusting and making necessary corrections, complete all as specified and directed. |
| 6 | Demolition of unreinforced cement concrete, as in ground-floor flooring and paving, not exceeding 15 cm thick, below or above ground level, complete all as specified and directed. |
| 7 | Dismantling AC/CGI/fibre sheets, corrugated, semi-corrugated or similar, as in roofs, etc., complete all as specified and directed. |
| 8 | Dismantling wall or ceiling boards of any type, including fibre, pulp, insulation or similar boards/slabs/blankets of any thickness, fixed to any type of frame, including cover fillets. Any damage caused to electrical fittings/fixtures during execution shall be rectified by the contractor at his own cost and arrangement, including making good disturbed portions, complete all as specified and directed. |
| 9 | Dismantling concrete posts of any section and description, as in roof trusses, purlins, etc., including making good disturbed portions, complete all as specified and directed. |
| 10 | Dismantling floor, hearth and wall tiling, excluding backing, carefully removing serviceable tiles and removing rubbish off the premises. Any damage caused to electrical fittings/fixtures during execution shall be rectified by the contractor at his own cost and arrangement, including making good disturbed portions, complete all as specified and directed. |
| 11 | M&L for brickwork with fly-ash bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar (1:6), complete all as specified and directed. |
| 12 | All as per item hereinbefore but excluding bricks, complete all as specified and directed. |
| 13 | M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brickwork, finished even and smooth without using extra cement, complete all as specified and directed. |
| 14 | M&L for 15 mm thick rendering in cement mortar (1:4) on other than fair faces of brick or concrete wall surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 15 | M&L for rough-cast plaster on exterior walls, comprising an undercoat of cement mortar (1:3), not less than 10 mm thick, followed, while the undercoat is still plastic, by rough-cast mixture of crushed stone or fine gravel aggregate, 6–12 mm size, mixed with coarse sand and cement in the ratio of 1:1:1, applied and finished even. The cement-sand mix shall be slightly wetter than normal rendering to ensure thorough coating of the larger aggregate, complete all as specified and directed by the Engineer-in-Charge. |
| 16 | M&L for rendering in patches in repairs, each patch not exceeding 3 sqm, 10 mm thick in cement mortar (1:4) on fair faces of brick, stone or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed. |
| 17 | M&L for preparation of newly plastered wall surfaces and application of two coats of cement-based paint over one coat of primer, complete all as specified and directed. |
| 18 | M&L for preparation of newly plastered wall surfaces and application of two coats of oil-bound distemper over one coat of primer, complete all as specified and directed. |
| 19 | M&L for preparation of old decorated wall surfaces and application of one coat of oil-bound distemper of approved shade/tint, complete all as specified and directed by the Engineer-in-Charge. |
| 20 | M&L for machine-cut Kota stone flooring, 18–20 mm thick, laid over a 20 mm thick cement mortar (1:4) screed bed, bedded and jointed in grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing, complete all as specified and directed. |
| 21 | All as per item hereinbefore for machine-cut Kota stone flooring, but in skirting, over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified and directed. |
| 22 | M&L for grinding, rubbing and polishing existing Kota stone/terrazzo flooring, complete all as specified and directed. |
| 23 | M&L for 75 mm thick PCC (1:4:8), Type D-2, using 40 mm graded stone aggregate, in foundations, filling and mass concrete, as floor sub-base, complete all as specified and directed. |
| 24 | Providing and laying 60 mm thick, factory-made, chamfered-edge cement concrete paver blocks, Grade M-35, of approved colour, design and pattern, for footpaths, parks, lawns, driveways, light-traffic parking and similar areas, of required strength, thickness, size and shape, manufactured by table-vibratory method using PU moulds, laid in the required colour and pattern over and including a 50 mm thick compacted bed of fine sand, including spreading and levelling sand, embedding and compacting interlocking paver blocks using a plate vibrator, filling joints with sand, cutting blocks to the required size and pattern, finishing and sweeping off surplus sand, complete all as specified and directed. |
| 25 | M&L for coloured chequered cement concrete tiles, 300 × 300 × 25 mm thick, laid on floors, set and jointed in neat cement slurry and pointed with white cement mixed with pigment, including a 20 mm thick cement mortar (1:4) screed bed, complete all as specified and directed. |
| 26 | Providing and laying factory-made cement concrete kerb stones, Grade M-25, at or near ground level, set to the required line, level and curvature and jointed in cement mortar (1:3), including joints with or without grooves, joints not exceeding 5 mm thick except at sharp curves, and providing drainage openings wherever required, complete all as specified and directed. |
| 27 | M&L for non-skid ceramic tiles, 7–8 mm thick, each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in area, laid on floors, set and jointed in neat cement slurry and pointed with coloured cement to match the shade of tiles, over and including a 15 mm thick cement mortar (1:6) screed bed, complete all as specified and directed. |
| 28 | All as per item hereinbefore for non-skid ceramic tiles, but in skirting and dado, including 10 mm thick rendering in cement mortar (1:4), complete all as specified and directed. |
| 29 | M&L for coloured non-skid ceramic tiles, 7–8 mm thick, each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in area, laid on floors, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiles, over and including a 15 mm thick cement mortar (1:6) screed bed, complete all as specified and directed. |
| 30 | M&L for glazed ceramic tiles, any colour, 300 × 450 × 7 mm or 300 × 600 × 7 mm, on vertical surfaces, over 10 mm thick rendering in cement mortar (1:4), set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiles, complete all as specified and directed. |
| 31 | Excavating post holes or similar holes, each not exceeding 0.5 cum, getting out soil in loose/soft soil, returning, filling in and ramming earth or broken rubble mixed with earth around posts in layers not exceeding 25 cm, watering, removing surplus soil to a distance not exceeding 50 m and making good the surface, complete all as specified and directed. |
| 32 | S&F structural steelwork for trusses, purlins, rafters, etc., fabricated from hollow, square, rectangular or round sections, including vertical members, tees, angles, cleats, cutting, welding, notching and necessary connections, complete all as specified and directed. |
| 33 | M&L for preparation of new steel surfaces of any description exceeding 10 cm in width or girth and application of two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 34 | M&L for PCC (1:4:8), Type D-2, using 40 mm graded stone aggregate, in foundations, filling and mass concrete, complete all as specified and directed. |
| 35 | S&F pre-painted Galvalume aluminium-zinc-coated GI-based corrugated steel sheets, 0.50 mm thick, any colour, tensile strength 550 MPa, as roof covering or wall cladding, fixed with self-tapping screws, complete all as specified and directed. |
| 36 | S&F plain galvanised mild-steel sheeting, 0.50 mm thick, with zinc coating of 135 grade, in ridges, hips, valley gutters, drip and step flashings, including cutting and fixing to the required length and girth, complete all as specified and directed. |
| 37 | M&L for suspended false-ceiling system using 4 mm thick ‘E’ Board ceiling tiles, Classic/Designer type as approved by GE, size 595 × 595 mm, fixed to and including a galvanised iron powder-coated GI grid suspended from the ceiling with 4 mm dia galvanised wire and butterfly clips, wall-tapping screws and hold-down clips for fixing boards to the frame, complete as per manufacturer's instructions and as specified and directed. Grid details: (a) Grid size: 600 × 600 mm; (b) Main tee: 39 × 24 mm; (c) Cross tee: 29 × 34 mm; (d) Wall angle: 22.20 × 22.20 mm. |
| 38 | M&L for wall panelling using 5 mm thick pre-laminated PVC sheets with tongue-and-groove joints, wood-grain printed finish, fixed to walls on a PVC flat-strip frame of 40 × 5 mm at 300 mm centres in both horizontal and vertical directions, including PVC U-channels at top and bottom, PVC angles at all corners, solvent cement, screws, adhesive and fixing complete as per specifications and drawings, complete all as specified and directed by the Engineer-in-Charge. |
| 39 | Taking down existing bituminous tar-felt roofing, including plaster of any description over roof and terrace surfaces, flashings and junctions with parapets/curb walls, and removing rubbish to a distance exceeding 500 m but not exceeding 1 km and depositing where directed, complete all as specified and directed. |
| 40 | M&L for 20 mm thick screed bed in cement mortar (1:4), mixed with waterproofing admixture as per manufacturer's instructions, on concrete roof-slab surfaces, finished even and smooth. Waterproofing admixture shall be measured and paid for separately, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 41 | M&L for 20 mm thick screed bed in cement mortar (1:4), mixed with waterproofing admixture as per manufacturer's instructions, on concrete roof-slab surfaces, finished even and smooth. Waterproofing admixture shall be measured and paid for separately, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender