Tender For Provn Of Certain Elevated Sentry Posts Along The Bdy At Bd Bari Mil Stn Under Ge Kaluchak
Tender Value
43.79 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
10 days left
EMD
87580
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kaluchak → Jammu and Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Certain Elevated Sentry Posts Along The Bdy At Bd Bari Mil Stn Under Ge Kaluchak
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in over areas n exc 1.5 m deep and getting out in any type of soil complete all as specified and directed. |
| 2 | Add to item No 1 for each additional 1.5m or part thereof in depth beyond the first 1.5m complete all as specified and directed. |
| 3 | M & L for PCC (1:4:8) type D-2 using40mm graded stone aggregate in foundation/filling and mass concrete. complete all as specified and directed. |
| 4 | M&L for RCC M-30 Design Mix (20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 5 | M&L for RCC M-30 Design Mix (20mm graded aggregate) as in columns, piers,posts and struts all as specified and directed |
| 6 | M&L for RCC M-30 as in Beams, cantilevers, bressummers ,lintle over 1.5 m span complete all as specified and directed. |
| 7 | M&L for RCC M-30 Design Mix (20mm graded aggregate) as in slabs supported on walls, beams, columns in floor, roof , landings and the like complete all as specified and directed. |
| 8 | M&L Form work to sides of concrete foundation ,footings,bases of coloumns,raft foundation ,sides and soffits of foundation and plinth beam and similar work ,vertical or to batter,complete all as specified and directed. |
| 9 | M&L Form work to square,rectangular or polygonal fair finished surfaces of , pillars ,piers, post, and struts column complete all as specified and directed. |
| 10 | M&L Form work to flat fair finished surfaces to sides and soffits of floor or roof beam ,beam haunching ,girders ,bressummers ,lintle ,cantilever ,shelves including supports ,overhangs,etc also splays between floors and beams, complete all as specified and directed. |
| 11 | M&L Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work , not exceeding 20cm thick (Horizontal or sloping) complete all as specified and directed. |
| 12 | M & L TMT bars 10mm dia & over cut to length bent to shape as reqd, including cranking bending spirally for hoping for columns hooking ends & binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 13 | M & L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length bent to shape as reqd, including cranking bending spirally for hoping for columns hooking ends & binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 14 | M&L Brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 15 | M&L Rendering 10mm thick on fair faces of brick work or surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 16 | M&L Rendering 15mm thick on fair faces of brick work or surfaces in cement mortar 1:4 on external surfaces of wall etc finished even and smooth without using extra cement and mixed with integral water proofing compound @ 3% complete all as specified and directed. |
| 17 | Supply only integral water proofing compound all as specified and directed |
| 18 | M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 complete all as specified and directed. |
| 19 | Material & Labour for RCC chajja/fascia/parapet repair by using following steps :-(a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed.(b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours all as directed by Engr-in-Charge. |
| 20 | M&L hardcore ( broken stone or boulders) of gauge exc 63mm but n exc 100 mm deposited spread and leveled in layers n exc 15 cm thick watered and rolled / rammed to a true surface all as specified and directed |
| 21 | S&F for Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed . |
| 22 | S&F for 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and directed. |
| 23 | S&F MS works band, straps, holdfasts and similar small articles conforming to Fe290 Gde165 complete all as specified and directed. |
| 24 | S&F aluminium anodised barrel tower bolt of extruded sec of 150mm length complete all as specified and directed. |
| 25 | S&F aluminium handle of 150mm length complete all as specified and directed. |
| 26 | S&F for 100mm long stainless steel butt hinges medium weight cold rolled all as specified and directed, |
| 27 | S&F 300mm long Aluminium alloy, anodised sliding door bolt with complete fittings etc complete all as specified and directed. |
| 28 | Returning, filling in, including spreading, levelling ,watering and well ramming in layers not exc 25cm complete all as specified and directed. |
| 29 | Removing excavated material to be a distance n exc. 50m and deposting where directed at a level n exc. 1.5m above the starting piont ,complete all as specified and directed. |
| 30 | M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed bed laid and jointed cement screed bed laidand jointed with grey cemant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for floor and including15mm thick screed bed in CM 1:6 after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg og cement per sq. metre complete all as specified and directed. |
| 31 | M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed bed laid and jointed cement screed bed laidand jointed with grey cemant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for floor and including15mm thick screed bed in CM 1:6 after roughening surface of old concrete floor by picking sweeping clean and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg og cement per sq. metre complete all as specified and directed. |
| 32 | S&Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or slidingwith and including either hook sand hinges or steel hanging door fittings (exclusive of steel she eting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 33 | M&L preparation of new surfaces of wall and applying 2 coats of oil bound distamper emulsion over a 2 mm thick wall care putty complete all as specified and directed. Please Enable Macros to View BoQ information |
| 34 | M&L preparation of new surfaces of wall and applying 2 coats of oil bound distamper emulsion over a 2 mm thick wall care putty complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender