Tender For Provision Of Entrance Gate For Augmentation Of Railway Siding Near Thapan Dwar At Chandimandir Mil Station Under Ge Chandimandir.
Tender Value
26.50 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
16 days left
EMD
53000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Panchkula → Haryana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provision Of Entrance Gate For Augmentation Of Railway Siding Near Thapan Dwar At Chandimandir Mil Station Under Ge Chandimandir.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches in hard/ dense soil not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundations or for cesspits etc., and not exceeding 10 sqm on plan and getting out complete all as specified and as directed by Engineer-in-Charge. |
| 2 | Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge. |
| 3 | M&L for Cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed by Engineer-in-Charge. |
| 4 | M&L for Reinforced cement concrete 1:2:4 (nominal mix), type B-1 (using 20 mm graded stone aggregate) as in foundation including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; complete all as specified and as directed by Engineer-in-Charge. |
| 5 | M&L for Reinforced cement concrete 1:2:4 (nominal mix), type B-1 (using 20 mm graded stone aggregates) as in Columns, piers, posts and struts and the like complete all as specified and as directed by Engineer-in-charge. |
| 6 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge. |
| 7 | All as per Serial Item No. 6.00 here-in-before but 5 to 10 mm dia as in stirrups, spacers. |
| 8 | Use and waste of formwork for flat rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed by Engineer-in-Charge. |
| 9 | Use and waste of formwork for rough finished surface of concrete columns pillars, posts, struts, piers and stanchions concrete square, rectangular or polygonal etc., complete all as specified and as directed by Engineer-in-Charge. |
| 10 | S&F mild steel bolts, purpose made, with hexagonal or square heads at one end and screwed the other, or screwed both ends each screwed and to be fitted with washers and one hexagonal or square nuts exceeding 30 cm long & diameter of neck exceeding 12mm and not exceeding 20mm complete all as specified and as directed by Engineer-in-Charge. |
| 11 | S&F framed work such as grills, grating, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work for water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge. |
| 12 | S&F rolled mild steel sections as in roof trusses (framed), trussed, purlins, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar work conforming to Fe-410-W(Gde-E-250) quality A, complete all as specified and as directed by Engineer-in-Charge. |
| 13 | S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins, posts where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, Fe-410-W (Gde-Fe-250) quality-A complete all as specified and as directed by Engineer-in-Charge. |
| 14 | S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 410-W (GdeE- 250) quality A complete all as specified and as directed by Engineer-in-Charge. |
| 15 | M&L for preparation of new steel surfaces of any descripetion over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. |
| 16 | Supply and fixing anodised aluminum frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed by Engineer-in-charge.Note:- Weight of Aluminium section shall be ascertained by the BOO to be convened by the GE. |
| 17 | S&F 5mm thick ACP sheet fixed at site over plastered/ frame work surfaces including all fixing arrangements, adhesive/ stainless steel screws, etc., including shuttering arrangement upto 7 metre height complete all as specified and as directed by Engineer-in-Charge. |
| 18 | Supplying and fixing 3D projected lettering or figures (in Hindi or English) made of Stainless Steel (SS) 304L grade, with a sheet thickness of not less than 1 mm. Each letter or figure shall have a 3D projection/depth not exceeding 40 mm, a height of 45 cm, and a width of 30 cm. including fixing the letters at site over plastered walls at heights ranging from 3 to 10 metres on multi-storey buildings using hidden SS screws, anchors, or industrial adhesives, complete all as specified and directed by the Engineer-in-Charge.Note : Theme fonts of letters shall be approved by GE before procurement. |
| 19 | Returning, filling in and including spreading, levelling and well ramming not exceeding 25 cm thick in soil complete all as specified and as directed by Engineer-in-Charge. |
| 20 | Removing excavated materials not exceeding 50 metre and depositing where diretected at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed by Engineer-in-Charge. |
| 21 | cutting into or through concrete with or without reinforcement, upto a depth of 30 cm into concrete walls and trimming surface as required, girth exceeding 30 cm complete all as specified and as directed by Engineer-in-Charge. |
| 22 | S&F heavy duty top guide rollers/wheels with bracket |
| 23 | S&F heavy duty bottom load bearing guide rollers/wheels with bracket |
| 24 | Supplying and fixing automated sliding gate motor system, featuring a heavy-duty AC 2500 kg power lifter kit with an integrated control unit, operated on 230 V AC power supply, utilizing a heavy-duty rack and pinion drive mechanism to achieve a travel speed of 0.2 metre/sec, including provn and installation of a limit switch assembly, key-type manual over-ride release, thermal overload safety protection, one pair of wireless safety sensors (photocells), a hardwired push-button station and two hand held remote control transmitters, complete all as specified and as directed by the Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender