Tender For Special Repair To Bldg No 36 Mall Road Of 1 Up Air Sqn Ncc Under Ge (East) Agra.
Tender Value
49.89 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
15 days left
EMD
99800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Agra → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Bldg No 36 Mall Road Of 1 Up Air Sqn Ncc Under Ge (East) Agra.
BOQ
| Sl. No. | Item Description |
| 1 | Taking down existing roof treatment including all loose and de-bonded concrete/ screed, loose particles, dirt etc & Debris should be removed from Bldg. Roof substrate must be pressure-washed with water with, a minimum working pressure of 1,400 psi is to be used to and/or remove all dirt, dust, chalking and waste products. Remove algae, mold by using bleach solution or biowash etc complete all as specified and directed. |
| 2 | M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in roof kerbs, paddings, mud stops slightly chamfered or rounded in edges including required grove cutting and including water proofing compound @ 3% by weight of cement complete all as specified and directed. |
| 3 | M&L for applying 10 mm thick plaster in CM 1:4 including water proofing compound @ 200 ML each 50 kg by weight of cement finished even and smooth complete all as specified and directed. (water proofing compound shall be paid/measured saparatly ) |
| 4 | Supply only integral water proofing compound liquid admixture for mortar complete all as specified and directed. |
| 5 | M&L preparation of newly plasterd surface of roof incl cleaning the surfaces by using wire brush / pressure hose and applying high performance polythelene liquid membrane water prooing coating cold applied in two coats @ 1.5 kg/sqm two coats spray /brush applied with an elongnation of 300 % to 700 % and tensile strength of not less than 3 N/sqm as per ASTM D2370, crack bridging ability of 3.5 mm as per ASTM C1305, shore a hardness of not less than 60 as per ASTM D 2240. the item incl applying epoxy primer @ 0.15 Kg/Sqm and geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufactures instruction complete all as specified and directed. |
| 6 | Dismantling floor, hearth wall tiling including cement mortar bedding (but not backing) including rubbish off the premises complete all as specified and directed. |
| 7 | M&L for Virified double charged colour Ceramic joint free tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match ceramic coloured tiles joint free decorative (square/ rectangular) area of each tiles sqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. |
| 8 | M&L for Virified colour joint free ceramic tiles 10 mm thick (square/ rectangular)polished, area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm in skirting/vertical surface etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. |
| 9 | M&L for 7 to 8 mm thick non skid ceramic coloured tiles joint free (square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed with white cement and coloured pigment to match the tiles over 15mm thick screed bed in CM 1:6.complete all as specified and directed. |
| 10 | M&L for Coloured Glazed ceramic tiles 450x350x7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick rendering in CM 1:4 on brick wall complete all as specified and as directed. |
| 11 | Dismantling stone slabs of any description or thickness in floors / dados, etc laid bedded and pointed in any mortar complete all as specified and directed. |
| 12 | M&L Granite 20 mm thick in steps, pillars, window cills, pillars, window cills, cooking platforms and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rounding edges of stone slab one edge and including 20 mm thick screed bed or bedding layer of cment mortar (1:6) complete all as specified and as directed. |
| 13 | M&L Machine cut kota stone slab flooring 20-22 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 14 | M&L Kota stone slab 20-22mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed complete all as specified and as directed |
| 15 | Dismentling wall and ceiling board or insulation board /slabs/blanket any thickness including cover fillets etc all as specified and directed. |
| 16 | S&F in repair 605x605mm snap grid of powder coated galvanized iron of angle of size 23 mm x 23 mm of 30 gauge (Perimeter), T section of size 23 mm x35 mm main and 23 mm x 27 mm (intermediate) of 30 gauge suitable for false ceiling including GI wire 6 mm thick @ 1200 mm centre to centre both ways for hanging arragement complete all as specified and directed. |
| 17 | M&L for 4mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed. |
| 18 | M&L for refixing of 4 mm thick non asbestos fibre cement building board designer as in ceiling of size 600 x 600mm fixed to GI snap grid frame work complete all as specified & directed. |
| 19 | Preparation of old steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. |
| 20 | Dismentling wall panneling board or insulation board /slabs/blanket any thickness including cover fillets etc complete all as specified and directed. |
| 21 | S&F solid PVC Wall Lining for wall panelling consisting of 5 mm thick printed colour PVC sheet inclusive fixing with all accessories complete all as specified and directed. |
| 22 | M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame complete all as specified and directed. |
| 23 | Demolition of brick work or stone/boulder masonary built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed. |
| 24 | M&L Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed. |
| 25 | Dittto all as item No 24 above but except bricks complete all as specified and directed. Note:- (1) Bricks obtained from item No 23 shall be reused after cleaning. (2) No extra payment shall be made for clearing of old bricks. |
| 26 | M&L brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius in half brick thick wall built in CM 1:4 complete all as specified and directed. |
| 27 | Taking down cement / lime plaster, and any kind wall cladding tiles/brick stone of any discription on bricks or stone walls/ceiling etc including racking out joints, hacking for kay, scrubbing down with water complete all as specified and directed. |
| 28 | M&L for 15mm thick plastering in CM 1:6 on brick surfaces of walls & finishing the surface even & smooth complete all as specified and directed. |
| 29 | M&L for 15mm thick plastering in CM 1:4 on brick surfaces of walls & finishing the surface even & smooth complete all as specified and directed. |
| 30 | M&L for washed stone grit plaster on exterior walls in two layers , under layer 12mm thick cement plaster 1:4 ( 1 cemant : 4 coarse sand ) furrowing the under layer with scratching tool , applying cement slurry on the under layer @ 3 Kg of cement per sqm , top layer 15 mm th cement plaster 1 :1 / 2 :2 ( 1 cement : 1/2 coarse sand : 2 stone chipping 10 mm nominal size ) in panels with groove all arround as per approved pattern incl. scrubbing and washing the top layer with brushes and water to expose the stone shipping complete all as specified and directed. |
| 31 | Forming groove of uniform size 15 mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens nailed to the under layer incl. removal of wooden battens, repair to the edges of panels and finishing the groove complete all as specified and directed. |
| 32 | M&L for rendering 10mm thick in two coats each 5 mm thick plastering on concrete surfaces of ceiling in CM 1:3, finished the surface even & smooth complete all as specified and directed. |
| 33 | M&L for preparation of old plastered or unplastered surfaces of ceiling and applying one coat of white wash complete as specified and directed. |
| 34 | M&L for preparation of newly plastered surfaces of ceiling and applying three coat of white wash complete all as specified and directed. |
| 35 | M&L for applying Two or more coats of acrylic emulsion polymer paint (wateproof rain coat having, Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new plastered surfaces of wall including preparation and over 3 mm thick wall care putty complete all as specified & directed. |
| 36 | M&L for applying Two or more coats of acrylic emulsion polymer paint (wateproof rain coat) having, Alkali & fungal resistance, dirt resistance exterior paint of required shade over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old plastered surfaces of wall care putty over old plastered surfaces of wall including complete removal of existing treatment of wall and over 3 mm thick wall care putty complete all as specified & directed. |
| 37 | Complete removal of existing treatment of old plastered or unplastered surfaces of walls and applying two coats of oil bound distamper over a coat of 3 mm thick wall care putty complete all as specified and directed. |
| 38 | Preparing new plastered or unplastered surfaces of walls and applying two coats of oil bound distamper over a coat of 3mm thick wall care putty incl rubbing complete all as specified and directed. |
| 39 | Taking down chowkats or frame with shutter (without taking off shutters from the frame) not exc 1.5 Sqm each complete all as specified and directed. |
| 40 | All as per item No 39 before but exc 1.5 Sqm and not exc 4.00 Sqm each complete all as specified and directed. |
| 41 | S&F factory made uPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. Comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed.(Glass shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made complete all as specified and directed. |
| 42 | S&F factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead /double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed . (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be madecomplete all as specified and directed. |
| 43 | S&F 08 mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including all fixing acesscess cutting to shape, drilling holes required. complete all as specified and directed. |
| 44 | S&F , 5.5 mm thick sheet glass selected quality and fixed with glazing clip to window shutter complete all as specified and directed. |
| 45 | S&F of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 52 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy-duty stain less steel pivot hinges shall be provided per shutter. The windows should be panelled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self-expanding, screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes etc as specified and directed. |
| 46 | S&F of ventilator made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 48x50mm, centre mullion should be of 48x50mm, section for shutter should be of 52x 25mm and rebate for Glazed shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Handle, stay, 2 nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float glass with rubber gaskets including fixing the frames in concrete/masonry wall by means of self expanding screws, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc., complete for finished item of work. |
| 47 | M&L Mild steel farmed work as in doors (as in ckowkats/shutter frame) or gates of angle or other section with guest plates rail, brasses rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to GdeFe-410-W(Gde-E-250)quality-B including shop coat of red oxide including prepration of surface before fixing complete all as specified and directed. |
| 48 | M&L for Mild steel, plain, black sheet 1 mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, ncluding bending or turning up, mitred angles, etc. as required complete all as specified and directed. |
| 49 | S&F 30mm thick flush door shutter, with particle board core construction , and plywood face pannels , commercial type on the both sides complete all as specified and directed. |
| 50 | S&F Factory made single extruded WPC (wood polymer composite) solid door/window/ cesetory windows & other frames / chowkhat of decorative type/wood grain printed colour of size 50x100 mm comprising of virign PVC polymer of K value 58-60 (suspension grade) calciam Calcium carborate and naturan fibers (wood powder/ rice husk/ wheat husk ) and non toxic additives (maximum toxity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwd with full body threated star headed SS screw having minimum frame dencity of 750 kg/ cum. Srew withdrowl strenghth of 2200 N (Face) & 1100 N (Edge). minimum comp ressive strenth of proof. water/modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer froff water /moister proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasterners of required dia and lenth completed as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. variation in profile dimension on plus side shall be acceptable but no extra payment on this account shall be made |
| 51 | S&F factory made single extruted WPC ( wood polymer composite ) solid decorative type/wood grain printed color flush door shutter of size 35 mm thick comprising of virson polymer of k value 58-60 (Suspension Grade ) calcium carbonate and natural fibers (wood powder/rice husk /wheat husk and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum dencity of 650 kg/cum and screw withdrowl srength of 1800 N (face) & 900 N (Edge). mimimum compressive strength 50 N/mm2, modulud of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof. water/molstrureproof and fire retardent. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and including S & with stainless steen butt hinges of required size with neccesory full body treaded star headed counter sunk S>S screw completed as specified and directed. |
| 52 | Resecuring or easing adjusting to door shutter of any description or any type area of each door exc 2 Sqm without taking down complete all as specified and directed. |
| 53 | Resecuring or easing adjusting to door shutter of any description or any type area of each door exc 1 sqm but not exc 2 Sqm without taking down complete all as specified and directed. |
| 54 | Resecuring or easing adjusting to chowkat of any description or any type area of each exc 1.5 sqm but not exc 4 Sqm with out taking down complete all as specified and directed. |
| 55 | S&F aluminium (extruded section) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 56 | M&L for providing, PCC 1:3:6 type C-1 (using 20mm graded aggregate) for embedding hold fasts/coping /padding including necessary form work etc.complete all as specified and directed. |
| 57 | S & F, 150mm floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 58 | S&F in repair drapery (curtain) rod 25mm dia Stainless steel grade 304 approved quality and colour including side cups,fixing arrangement with drilling holes in walls brackets etc complete all as specified and directed. |
| 59 | Demolition of cement concrete in ground floor and paving n exc 15cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed. |
| 60 | M&L 75 mm thick Cement concrete type C-2, 1:3:6 using 40mm graded aggregate complete all as specified and directed. |
| 61 | Taking up or down 15mm dia steel tubing and connections etc complete all as specified and directed. |
| 62 | S&F 15 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 63 | Taking up or down 20 mm dia steel tubing and connections etc complete all as specified and directed. |
| 64 | S&F 20 mm bore GI tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 65 | S&F in repairs oval type wash basin superior quality 537x439 mm size incl fitted with granite top/baroda green stone over precast RCC slab including waste coupling and incl suitable size CP bottle trap connected upto grating complete all as specified and directed. |
| 66 | M&L for demolition of reinforced cement concrete of any description and in any position complete all as specified and directed. |
| 67 | M&L for Reinforcement cement concrete (Nominal Mix) 1:2:4 type B1 (using 20mm stone aggregrate ) as in slab supported on wall for wash hand complete all as specified and directed |
| 68 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work and fair finished surface not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 69 | S&F mild steel bars 10 mm dia and over (TMT) cut to length bent to shape required including cracking, bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel conforming to Fe-410-0 or Fe-410-S. complete all as specified and directed. |
| 70 | S&F mild steel bars 5 mm dia and over up to 10 mm dia in stirrups space and binders. (TMT) cut to length bent to shape required including cracking,bending spirally for hooping ends and binding with and including mild steel wire not less than 0.90 mm dia quality of steel. complete all as specified and directed. |
| 71 | S&F in repairs Flushing jet spray for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed. |
| 72 | S&F Vitreous china wash down water closed pan (Pedestal Pattern ) with 'P' and 'S' trapp including connection to trap and cistren and flush pipe (excl flushing cistren)and making good to disturbed surface of floor all fixed as in repairs all as specified and directed. |
| 73 | S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket or PPR pipe etc making good disturbed portion complete all as specified and directed. |
| 74 | S&F in repair 15 mm bore CP Angle valve two way fancy type with wall flane, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified & directed. |
| 75 | S&F in repair 15 mm bore, single lever brass chromium plated wash basin mixer wothout popup waste with 450mm braided hoses opal prime fixed to wash hand basin complete all as specified and directed. |
| 76 | S&F in repairs toilet paper holder with flat recessed type stainless steel, chromium plated or stainless steel with necessary brass nuts & rubber washers, covered with chromium plated spring complete all as specified and directed. |
| 77 | S&F in repair of plastic WC seat cover and mild steel chromium plated or aluminised hinging device as etc complete all as specified and directed. |
| 78 | S&F in repairs Flushing Health Faucet for pedestal pattern WC incl .flexible pipe and brass chromium plated nuts and bolts and water pipe of size 1150 mm long between dia & fixed completed all as specified and directed. |
| 79 | S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed. |
| 80 | S&F in repairs 10litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and PVC connections 15mm size with PTMT nuts of length 450mm inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbe portion complete all as specified and directed. |
| 81 | S&F in repair brass C P tubular towel rail, 60 cm long, 20mm bore, chromium plated complete all as specified & directed |
| 82 | S&F CI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 100 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. |
| 83 | S&F CI floor trap, plain with grating including jointing with solvent cement (Diameter of outlet 75 mm), jointing to waste pipe and fixed in cement concrete 1:2: 4 (type B1) mixed with pedilite water proofing liquid @ 200ml in 50 kg cement, inlcuding taking out of old unserviceable connections etc, connecting up new and making good disturbed portion complete all as specified and directed. |
| 84 | S&F 100 mm bore cast iron soil, waste vent sand cast pipes in any length with or without ears, with cement joints fixed to walls including making good disturbe portion to match the existing complete all as specified and directed. |
| 85 | S&F 75 mm bore cast iron soil, waste vent sand cast pipes in any length with or without ears, with cement joints fixed to walls including making good disturbe portion to match the existing complete all as specified and directed. |
| 86 | S&F in repair two way angular valve , 15mm dia, cast copper alloy,CP fancy type with long shank and cup screwd down, high pressure ,screwed both ends for iron pipes or for unions and fixed in pipe all as specified and directed. |
| 87 | S&F in repair CP soap dish brass chromium plated, size 100 x 60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. |
| 88 | S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. |
| 89 | M&L 100 mm long aluminium anodized handle cast type complete all as specified and directed. |
| 90 | S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. |
| 91 | S&F Aluminium alloy, anodised, 250 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 92 | S&F in repairs Vitreous China Urinal, full stall type complete including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing arounds urinal back in cement , fixing of nozzles for discharge of water flushing pipe and grating and union for discharge pipes etc complete all as specified & directed. |
| 93 | Removing or dismantling of damage / cracked/ concrete /loose concrete / plaster of celing/ wall/ chajja/ facia to expose the sound and hard concrete using a suitable mechanical device or by hammer and chisels etc complete all as specified & directed. |
| 94 | M&L for providing and applying on beam, col, ceilings surface by one part alkaline based material with corrosion inhibitors and dispersing agents for exposed steel surface after cleaning to loose scale or oxidized chips from bars, having bulk density 1.25. The material to be applied to the rusted metal with brush for complete wetting of rusted metal surface and allowed to react for 16-24 hours. After 24 hours, a white layer will appear which will protect further corrosion of metal / steel after about 5-7 days, before applying protective coating, the surface should be wire brushed and thoroughly cleaned for dust with dry cloth etc to make surface dust free complete all as specified and directed. |
| 95 | M & L for applying bonding agent for bonding old to new concrete surface likes chajja/ beams/ celings/ columns/ facia etc by high performance modified Styrene- Butadiene Rubber ( SBR ) base binder . Applying of binder is as 10 sqm/ per litr ( including necessary arrangements in multy storey bldgs up to height 7 mtr ) etc complete all as specified & directed. |
| 96 | M & L for applying 25 mm thick ( average ) smart care repair mortar ready to use single component polymer modified repair mortar for repair of RCC members likes beams, columns, chajja , facia , mortar having good compressive strength of not less than M-30 and shrinkage resistance, mixing as per manufacture instruction etc ( including necessary arrangements in multy storey bldgs up to height 7 mtr ) complete all as specified & directed. |
| 97 | S&F galvanised welded steel wire fabric as extra reionforcement to RCC members like ceilings, chajja’s, beams, columns parapet walls, waste slab etc including all cutting and waste (wt not exc 4.00 kg/Sqm) complete all as specified and directed. |
| 98 | S&F in repair powder coated aluminium section for fixed partition with extruded built up standard tubular section as per required size & Wt. of section can not be less than 0.55 Kg / Rm ,appropriate Z section and other section of approved make confirming to IS 733 and IS 1285 including 5 mm thick Plain glass in upper portion and 8 mm thick ACP/APP sheet of any colour fixing with dash board fasterners of required dia and size including necessary fitting up the gaps at jucntions i.e. at top and bottom and sidewith required EPDM/rubber/neoprene gasket etc. Aluminium sections shall be smooth rust free straight mitred including clar angle aluminium snab beading for glazing/panelling CP brass/stainless steel screws all as specified and directed . |
| 99 | S&F in repair 500 ltrs capacity rotational moulded polyethylene white colour water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of water tank complete all as specified & directed. |
| 100 | S&F in repair 1000 ltrs capacity rotational moulded polyethylene white colour water storage tank double layered, ISI engraved (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of water tank complete all as specified & directed. |
| 101 | S&F in repairs 5 mm thick bevelled edge mirror of selected quality glass of required size and shape with 50x20 mm teak wood polished beading mounted on 6 mm thick commercial ply wood / ACP / PVC and fixed to wooden plugs with chromium plated brass screw and cup washers complete all as specified and directed. |
| 102 | Demolition of cement concrete in ground floor and paving n exc 15 cm thickness (below or above the ground level) built in cement mortar complete all as specified and directed . |
| 103 | M&L,cement concrete 1:4:8 type D2 (40 mm graded stone aggregate ) in foundation filling and mass concrete complete all as specified and as directed. |
| 104 | M & L for coloured designer chequered tiles 300 X 300 exterior grade 20 mm thick laid over 15 mm thick screed bed in CM 1:6 set & jointed in neat cement slurry with pigments to match the tile, complete all as specified |
| 105 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; all as specified and directed |
| 106 | S&F 18mm thick plain solid PVC decorative choice for cup board and kitchent cabinet /almirah shutter suitalbey fixed in MS angle frame work as per specification ( Ms frame work shall be measured and paid seperately complete all as specified and directed. |
| 107 | S&F 100mm long alluminium handles, cast type, anodized and fixed complete all as specified and directed. |
| 108 | S&F in continuous (Piaano) hinges MS Bright finish width of flap 30 mm when open complete all as specified and directed. |
| 109 | S&F Brass magnet catcher suitable for CB/cabinet shutter complete all as specified and directed. |
| 110 | Dismantling asbestos cement (corrugated, semi-corrugated sheet/ North light curve, Ridge etc.) sheets in roof coverings complete all as specified and directed. |
| 111 | Cutting Chases, pinning in brick/Concreate wall making good to facing where required and pointing in cement mortar 1:3 ends of edges of landing, steps cills sunshade shelves lintles etc and cutting chase for concealed water tubing or or concealed conduit wiring. etc and making good cutting N. exceeding 10 CM girth complete all as specified and directed. |
| 112 | S&F of Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 113 | Preparation of old steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed |
| 114 | S&F for MS framed work confirming to Fe-410-O or Fe-310-O as in Gates including pintle hinges, stops, rolling wheets , MS Sheets , hand made sliding bolts,grill/gratings, as in sliding gates etc. side hung type complete all as specified and directed. |
| 115 | Taking down carefully existing unserviceable copper / aluminum point wiring of any description & in any position with and ncluding taking out existing unserviceable conduits or battens of any description with sunken boxes/junction boxes and all fitting, accessories & fixtures such as switches, ceiling roses, pendants, regulators, socket, light fittings, lamp holders etc but excluding tube light fittings and making good the disturbed surface of walls, floors, ceiling etc to match with the existing surfaces complete all as specified and directed. |
| 116 | M&L point wiring with 1.5 sqmm multi stranded copper conductor 1100 volts. grade FRLSH PVC insulated unsheathed cable with proper colour coding drawn in including PVC concealed conduit not less than 20 mm dia with all accessories and FRLSH PVC insulated 1.5 Sqmm multi standard unsheathed copper wire for continues earth, including cutting and chasing of wall surface for laying PVC conduit and modular sunken box and connecting earth and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCB's or bus bar shall be done through proper size copper/brass thimbles. Note :Conduit shall be fixed on surface of roof with necessary saddles where concealing of conduit is not feasible at no extra cost for the following :- (a) One light /fan point controlled by one switch |
| 117 | (b) One 5 pin socket outlet 5 Amps on independent board |
| 118 | (c) One 5 pin socket outlet 5 Amps on same board |
| 119 | (d) One bell/buzzer point controlled by one push button on the same board with other switches or independent |
| 120 | All as per item No 116 here in before but with cable size 4 Sq mm for one 5 pin 15/16 Amps socket out let on independent board and multistrand insulated copper earth continuity conductor of size 4 sqmm all as specified and directed. |
| 121 | S&F modular switch piano single pole, one way 6 Amps 1 module, complete all as specified and directed. |
| 122 | S&F modular switch piano flush type 16 Amps single pole one way, one module, complete all as specified and directed. |
| 123 | S&F modular socket outlet 2/3 pin 6 Amps combined 2 module, complete all as specified and directed. |
| 124 | S&F modular socket multipurpose 3 pin 6/16 Amps combined 2 module, complete all as specified and directed. |
| 125 | S&F Modular Bell push 6A 1 module pole, one way, complete all as specified and directed. |
| 126 | Supply and fixing in repair call bell, Ding dong type, 230 volts AC single pole complete all as directed. |
| 127 | S&F for ceiling rose PVC Polycarbonate isolated body 62.5 x 25 mm, three terminals, complete all as specified & directed. |
| 128 | S&F modular cover plate with frame (inner and outer) 1 module for mounting switch and sockets complete all as specified and directed. |
| 129 | S&F modular cover plate with frame (inner and outer) 2 module for mounting switch and sockets complete all as specified and directed. |
| 130 | S&F modular cover plate with frame (inner and outer) 3 module for mounting switch and sockets complete all as specified and directed. |
| 131 | S&F modular cover plate with frame (inner and outer) 6 module for mounting switch and sockets complete all as specified and directed. |
| 132 | S&F modular cover plate with frame (inner and outer) 8 module for mounting switch and sockets complete all as specified and as directed. |
| 133 | S&F blank spacer plate for single module complete all as specified and as directed. |
| 134 | S&F 20 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 20W, luminaire lumens > 2000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surge protection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certification and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified and directed. |
| 135 | S&F 10 watt LED battan surface / wall mounted with specially designed powder coated aluminum housing, high optically efficient polycarbonate diffuser, in built electronic driver duly pre-wired upto terminal block, power consumption < 10W, luminaire lumens > 1000 lms, driver efficiency > 85%, power facor > 0.95 THD < 20% as per IEC 61000-3-2, colour temp - 6500 K Surge protection 2.5 KV, 50000 burning hrs (min) as per L 70 criteria, two stages isolated constant current operated driver with range 150 - 270 VAC and safety extra low voltage safe level < 60 VDC as per IEC standard with LM 70 & 80 certification and connecting the same to electric source with & using PVC sheathed and insulated three core copper conductor cable of size 0.75 Sqmm and fixing arrangements for fixing the light fitting, complete all as specified and directed. |
| 136 | S&F LED security light compact & trendy of 35 watt with aluminium pressure diecast housing, IP 65 protection, luminaire lumens > 3000 lumens/W and in built electronic driver prewire upto terminal block with driver efficiency > 85 %, power factor > 0.95, as per IEC 61000-3-2, colour temp 6500 K Surge protection 3.5 KV, 50000 burning hrs (min) as per L70 Criteria, multi stage constant current operated driver with range 150-270 VAC and safety exra low voltage safe load < 60 VDC as per IEC standards with LM 70 & 80 certification complete all as specified, fixed to pole or wall of buiding with and including suitable Bracket made out of 25 mm dia GI light grade pipe, 1.0 m long bent to shape by cutting & welding as required & directed and fixed with two Nos of FI clamps 50x6 mm to be tightened with suitabe size of bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer, and including connecting the fitting to electric source with & including twin twisted copper flexible wire of size 0.75 Sqmm including all accessories and fixing arrangements for fixing the light fitting complete all as specified & directed. |
| 137 | S&F LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. |
| 138 | Disconnecting & taking up or down existing unserviceable sub main wiring of copper/aluminium conductor of any description, any size & in any position including taking out existing unserviceable conduits or battens of any description and making good the disturbed surfaces to the existing surfaces complete all as specified and directed. |
| 139 | M&L for sub main wiring using two 2x 6 sqmm single core FRLSH PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn in and including concealed PVC conduit (Medium grade) of dia not less than 20 mm with standard accessories along-with one run of PVC (green colour) insulated , unsheathed, stranded copper conductor of size 6 Sqmm as earth continuity conductor connected to earth dolly complete all as specified and directed. (NOTE : Two run of single core PVC cable with one run of earth conductor and conduit /batten shall be measured as one unit.) |
| 140 | Disconnecting and taking down old unserviceable distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces to the existing surfaces complete all as specified and directed. |
| 141 | S&F in repair/replacement of sheet metal enclosure Vertical TPN DB 4 way as per IEC 61439-3, Suitable for Flush Mounting and Surface Mounting, With 160 A Copper Busbar for each phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management, fully insulated busbar & shrouded Neutral bars, Improved Pan assembly for ease of installation, Prefitted masking sheet, Reversible Door for IP- 43 DB's, With provision for 160 Amps MCCB as incomer and SP/TP MCB's as outgoing complete all as specified and directed. |
| 142 | S&F sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 8 way with IP-43 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed. |
| 143 | S&F sheet metal enclosure MCB distribution board. Single pole & neutral 240 volts 12 way with IP-43 protection double door complete with appropriate size bus bar and neutral link complete all as specified and directed. |
| 144 | S&F in repair sheet metal enclosure with socket plug top and MCB single pole and neutral with two pin and earth plug top with one SP MCB 20 Amp 240 volt complete all as directed all as specified and as directed. |
| 145 | S&F MCB SP 5 to 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed. |
| 146 | S&F MCB SPN 32 Amp ('C' curve) having short circuit rating 10KA, 240 volts complete with connection testing and commissioning. Complete all as specified and directed. |
| 147 | S&F in repair MCCB 4 pole, 160 Amps, 50 Hz, Icu=25 KA at 415 volts with thermal magnetic alongwith adjustable magnetic protection for current setting Icu=Ics = 100% with adjustable over load setting (minimum 70% to 100%) value from 10 to 15 times of related capacity as per IEC-60947-1 and 60947-2 standard complete all as specified and directed. |
| 148 | M&L for earthing complete with galvanized earth plate electrode 600 x 600 x6mm thick burried directly in ground vertically to a depth not less than 2.25 M below normal ground level ) with top edge of the plate not less than 1.50 M below normal ground level , connected to and including galvanized steel wire 4mm dia as earth lead soldered and riveted to earth plate by means of nuts, bolts, check nuts & washers, of galvanized iron or steel with connected to test point and testing on completion including 15mm GI light grade pipe for earth lead protection from earth point to earth plate, including provn adequate quantity of charcoal dust mixed with 35 % common salt to a packed thickness of not less than 15 cm in alternate layers of charcoal and salt on all sides of earth plate with 20mm bore medium grade GI Pipe for watering,GI check nut, funnel and wire mesh with and including all necessary excavation & earth work in soft/loose soil, returning filling in, removal of surplus soil to a distance 50 metre,,PCC 1:3:6 type C-1 as in earth pit, 40 mm thick RCC cover using cement concrete 1:2:4 type B-1 reinforced with & including 8 mm dia mild steel TMT bar @ 100 mm c/c Both way with suitable handle for lifting arrangement & including form work complete all as specified and shown in electrical plate No 3 of MES SSR Part I 2009 and as directed. NOTES:- (i) On testing, after completion of Job, if desired earth resistance is not obtained, the earthing shall be redone at without any extra cost by contractor. |
| 149 | Dismantling, taking down exisitng ceiling fan/Exhaust fan and deposited to E/M store for re-fixing and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed. |
| 150 | S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete all as specified and directed. Please Enable Macros to View BoQ information |
| 151 | S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m, complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender