Tender For Development And Beautification Work Of Jatayu Park Based On Nath Corridor Theme On The Land Of Horticulture Department Near 100 Foot Road Delapir.
Tender Value
7.31 Crore
Estimated cost
Bid Submission
20 Nov 2026
24 days left
EMD
14.64 Lakhs
Bank guarantee accepted
Document Fee
20000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Development And Beautification Work Of Jatayu Park Based On Nath Corridor Theme On The Land Of Horticulture Department Near 100 Foot Road Delapir.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil.D.S.R. Item No. 2.8.1 |
| 2 | Providing & laying cement concrete 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.8 |
| 3 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriagefor all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 350 kg /cum All works upto plinth level RCC as in fdns and footings of colums and plinth beam and bases of column. DSR Item No. 5.33.1.1 |
| 4 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cum (level 1 to lvl-5) D.S.R. Item No. 5.33.2.1 |
| 5 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominalsize derived from natural sources)..DSR Item No. 4.2.2 |
| 6 | Mild steel or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an overall rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage and over lapping and hooks and authorised overlapping shall be measured . D.S.R. Item No. 5.22.1 |
| 7 | Centering and shuttering including strutting, propping etc. and removal of form for footings/PB, rough finished surface of conc. D.S.R. Item No. 5.9.1 |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roof , landings, balconies, acessess platformD.S.R. Item No. 5.9.3 |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.D.S.R. Item No. 5.9.2 |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for Lintel Beams, Plinth Beams, Girders, bressumers and cantiliversD.S.R. Item No. 5.9.5 |
| 11 | Brick work in foundation 1st class b/work in 1:4cement and couarse sand mortar in fdn and plinth incl. supply of all materials , labour and t& P required for proper completion of the workD.S.R. Item No. 6.2.1 |
| 12 | Brick work in SUPER STRUCTURE in 23 cm thk wall with 1:4 cement and coarse sand incl. all materials labour annd t&p etc. for proper completion of work.D.S.R. Item No. 6.4.1 |
| 13 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksD.S.R. 2023 Item No. 10.1 |
| 14 | 12 mm thk plaster (1:4) with cement & Coarse Sand (Fair Face)D.S.R. Item No. 13.4.1 |
| 15 | Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80 |
| 16 | Finishing walls with Acrylic Smooth exterior paint of required shade :-New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10sqm.).D.S.R. Item No. 13.46.1 |
| 17 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new workD.S.R. 13.62.1 |
| 18 | Construction of granular sub base (G.S.B.) by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, compete at per clause 401. (Analysis Rate), |
| 19 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator,filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.D.S.R. 2023 Item No. 16.91.2 |
| 20 | Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20 mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10 mm wide filled with same mortar including ruled pointing etc. complete as per direction ofengineer-in-charge.D.S.R. 2023 Item No. 16.92 |
| 21 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, EliteBrown, Cat Eye or equivalent.D.S.R. 2023 Item No. 11.55.1 |
| 22 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approvedby Engineer-in-charge).D.S.R. Item No. 16.69 |
| 23 | Providing and laying in position specified grade of cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)D.S.R. Item No. 5.1.3 |
| 24 | Earth Filling including cartageEarth work cutting on in embankment in ordinary soil earth work in embankment to be in 20cm layers including watering dressing and compacting the soil to achieve 95% proctor density and also including the surface required level and slops and also including lift 1.50m and lead 8km.D.S.R. No. 1.1.2 |
| 25 | FOAM BUBBLER IN LINE FOUNTAIN OF PREMIERE WORLD FOR MAKE 1. Fountain comprises of Foam Bubblers in Line. Fountain consists of 08 nos. Foam Bubblers with ball joint nozzles Nozzles are made of Brass- nickel/Chrome plated. High quality 2.Supplying, Installation & Testing of Pump set & electric panel comprise of totaling 7.5 HP monosumbersible pump set (Kirloskar/Equivalent.) Panel comprises of motor main switch, contactors, overload relays, switch fuses, light sequencer, push button on off switches, 3. Supplying, Installation & Testing of Pump set & electric panel comprise of totaling 7.5 HP monosumbersible pump set (Kirloskar/Equivalent.) Panel comprises of motor main switch, contactors, overload relays, switch fuses, light sequencer, push button on off switches4. supplying , Installation & Testing of 3 core Submersible cable for pump & 4 core 1.5 sqm double insulated cable for luminaries with cable ties. 5. Transportation, Installation & Testing of Fountain. |
| 26 | 1.75 MTR DIA HALF BALL FOUNTAIN OF PREMIERE WORLD FOR MAKE (Pool size req: 6 Mtr Dia) 1. Fountain consists of multiple nozzles on stick creating the mist in half ball shape. Nozzles are made of Brass- nickel/Chrome plated. High quality 2.Supplying, Installation & Testing of Pump set & electric panel comprise of totaling 5 HP monosumbersible pump set (Kirloskar/Equivalent.) Panel comprises of motor main switch, contactors, overload relays, switch fuses, light sequencer, push button on off switches, 3. Supplying , Installation & Testing of 21w LED LIGHTS .The housing, top cover and bracket are all in polished stainless steel, fasteners are also stainless steel, Design is extremely compact, Special measures have been taken for protection of components and sealing, totally protected against ingress of water 4. supplying , Installation & Testing of 3 core Submersible cable for pump & 4 core 1.5 sqm double insulated cable for luminaries with cable ties. 5. Transportation, Installation & Testing of Fountain. Make: Premiere World Fountain |
| 27 | Providing and fixing 5 feet long straight bench comprising MS fabricated frame, supports, seat/backrest, necessary fasteners, anti-corrosive primer and two coats of approved paint, complete in all respects as per approved drawing/designRate as per Ramayan Vatika (P.S.) |
| 28 | Aerated white water jet. Nozzle made of aluminium alloy – epoxy coated. This aerating jet fountain is especially designed to aerate, distribute and circulate water in pools, lakes, waterbodies etc. to improve and maintain water quality. Fountain comprises of necessary accessories made of steel – galvanized/epoxy coated and/or extruded aluminium alloy and/or aluminium. (make- premierworld ) Approx. height of water effects : Calyx jet –380mm, Center jet – 910mm Pumpset & control panel : Supply, Installation, Testing & Commissioning of Pumpset & electric panel comprise of totaling 1.5 hp monosumbersible pumpset (Kirloskar/Sona/Premier Fountains’ make). Submersible with grouting bolts. Special Large area mesh filter for each Pump. Filter’s body made from galvanized steel & filter’s mesh made from stainless steel. Pump suction covered with large area mesh filter, filter body made from galvanized steel, filter mesh made from stainless steel, three phase, 380-440V AC, 50 cycles supply with foundation bolts and 3 core flat PVC flexible copper conductor double insulated submersible cable Electric panel comprises of steel sheet paint finish enclosures with hinged front door, back-wall mounting type with provision for incoming & outgoing cable entry. Panel comprises of motor main switch, contactors, overload relays, switch fuses, light sequencer, push button on off switches, indicating lamps etc. complete with internal wiring. Lighting system shall be connected by a separate switch and fuse but shall not be energized unless pump is first switched on .Control Panel: Control Panel in sheet steel paint finish enclosure with front hinged door back wall mounting type provision for incoming and outgoing cable entry, delay timer for star delta starting of motors complete with internal wiring. The electrical panel shall be protected against dust and jets of water per rating IP55 and shall have been tested and certified by a Government of India Test Laboratory. Panel comprises of motor main switches, contactors, overload relays, push button on off switch, switch fuses, indicating lamps etc. complete with internal wiring. Lighting system shall be connected by a separate switch and fuse but shall not be energized unless pumps are first switched on. LUMINARIES SYSTEM :03 nos LED21w wpl100 Waterproof luminaries with array of high output of LEDs housed in compact enclosure.(make:Premierworld)Make: Premiere World Fountain |
| 29 | Providing and fixing laser cut Acrylic Backlit letters (Acrylic Font) With LED backlit illumination made from approved quality cast acrylic sheet of required thickness (minimum 3–5 mm or as specified) for signage/branding work, including cutting as per approved design, polishing of edges, drilling holes, and fixing on wall surface with SS studs, spacer, adhesive or suitable fixing arrangement, complete in all respects including alignment, finishing, and cleaning as directed by Engineer-in-Charge.The rate shall include all materials, labour, tools, scaffolding, transportation, wastage, and installation complete as per approved drawing and site requirements.P.S. |
| 30 | C.C. 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)D.S.R. Item No. 4.1.3 |
| 31 | Centering and shuttering including strutting, propping etc. and removal of form for columns, pillers, piesr, abutment , post and strutsD.S.R. Item No. 5.9.6 |
| 32 | Class 150 Brick work in 1:3 cement and Coarse Sand of 1.25 finentss modulusbut in Parapet including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12 cms.D.S.R. Item No. 6.13.1 |
| 33 | Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150 mm to 300 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to 1S:2185 (Part 3) in super structure above plinth floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).Make: Ultratech /ACC/AmbujaD.S.R. Item No. 6.47 |
| 34 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)D.S.R. 13.5.1 |
| 35 | Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to IS: 2547 (Part -1 & II) 1976, applied on hacked / uneven background such as bare brick/block/ RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc. completeD.S.R. 13.78 |
| 36 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm.Make: Dulex, Asian Paints, BergerD.S.R. Item No. 13.45.1 |
| 37 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : 13.48.1 Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @Make: Dulex, Asian Paints, Berger0.75 ltr /10 sqmD.S.R. Item No. 13.48.1 |
| 38 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.1 Second class teak woodD.S.R. Item No. 9.1.1 |
| 39 | Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match themarble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.D.S.R. Item No. 11.51.1 |
| 40 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: DSR 22.7.1(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofingcompound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 andapproved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.D.S.R. 22.7.1 |
| 41 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finishof tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board Make: Armstrong, Gyproc by Saint-Gobin/Hunter DouglasD.S.R. ITEM No. 12.45.3 |
| 42 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Make: TATA/JINDE/APL Apollo TubesD.S.R. Item No. 10.28 |
| 43 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.Make : Ozone/Hettich/GrassD.S.R. Item No. 25.8 |
| 44 | Providing and fixing Stainless Steel H Shape Door HandleMake : Ozone/Hettich/GrassMR |
| 45 | Providing & Fixing Floor Lock Make : Ozone/Hettich/GrassMR |
| 46 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. dsr 9.82 Make : Ozone/Hettich/Grass |
| 47 | Providing, supplying, installing, testing and commissioning of sensor-operated automatic toughened glass door system, comprising of the following:Glass: 12 mm thick clear toughened (tempered) safety glass, conforming to relevant IS standards, with polished edges.Door Type: Automatic sliding/swing door system with motion sensor operation.Frame & Structure: Aluminium alloy frame (powder-coated/anodized finish) or frameless patch fitting systemTop track system with concealed mechanism (for sliding type)Automation System: Microprocessor-based control unitMotion sensor (infrared/radar based) with adjustable sensitivityBrushless DC motorEmergency stop and manual override facilityBattery backup (minimum 30–60 minutes operation)Hardware & Fittings:Stainless steel patch fittings (SS 304 grade)Floor spring (for swing type, if applicable)Door handle (SS finish)Rubber gaskets, EPDM sealsLocking arrangement (if required)Accessories:Safety sensor (anti-collision feature)Guide rails, rollers, stopper, and all necessary fixturesInstallation:Complete installation including alignment, fixing, wiring, testing, calibration, and making the system fully operational.Performance Requirements:Smooth, noiseless operationOpening/closing speed adjustableSafety compliance as per manufacturer standardsMake : Ozone/Hettich/Grass |
| 48 | Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge. Upto 10m. HeightD.S.R. 8.17 |
| 49 | Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge. dsr 8.22 |
| 50 | Providing and fixing copper pins 7.5 cm long 6 mm diameter for securingadjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2coarse sand), including making the necessary chases.D.S.R. 8.16 |
| 51 | Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides withpolymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neatD.S.R. 2023 Item No. 14.86 |
| 52 | Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.D.S.R. Item No. 16.72 |
| 53 | Providing, supplying, transporting and installing customized FRP Jatayu Sculpture of size 8000 mm width × 5000 mm height, fabricated in FRP as per approved design, drawing and sample, including all materials, moulding/fabrication, finishing, surface treatment, painting/colouring, detailing, loading, unloading, transportation to site and complete installation/erection at site, all complete as required and as directed by the Engineer-in-Charge.Market Rate |
| 54 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screwsD.S.R. Item No. 9.21.1 |
| 55 | Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to IS: 2202 (Part I)On one side onlyD.S.R. Item No. 9.22.1 |
| 56 | Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: 20 mm Dia D.S.R. 1.21.1 |
| 57 | Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: 25 mm DiaD.S.R. 1.21.2 (Rate: 145.00x0.755x0.97)=106.19 |
| 58 | Providing and fixing of junction box 200 x 250 mmPWD SI No 154 elctrical SOR 2018 |
| 59 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregateD.S.R. Item No. 11.3.1 |
| 60 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. D.S.R. Item No . 8.5 |
| 61 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite workD.S.R. Item No. 8.3.2 |
| 62 | Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.76 |
| 63 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarsesand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase D.S.R 2021No 12.21.1 |
| 64 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. D.S.R. No.12.22.1 |
| 65 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipeshaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufacturedfrom high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top coverD.S.R. Item No. 10.6.1 |
| 66 | Providing and fixing ball bearing for rolling shutters.D.S.R. Item No. 10.7 |
| 67 | Extra for providing mechanical device chain and crank operation for operating rolling shutters.Exceeding 10.00 sqm and upto 16.80 sqm in the areaD.S.R. Item No. 10.8.1 |
| 68 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge: make: Visaza/ Italicadsr 11.53 |
| 69 | Providing, fabricating, supplying, and fixing Glass Reinforced Concrete (GRC) decorative arch, ornamental panels, and columns of approved design and pattern, manufactured with high-grade cement, fine aggregates, alkali-resistant glass fiber, and suitable admixtures. The work includes molding, casting, curing, finishing, transportation to site, and installation with necessary MS framework, anchor fasteners, scaffolding, and all accessories complete, as per drawings and directions of the Engineer-in-Charge. The surface shall be finished smooth and ready to receive paint or protective coating.Market Rate |
| 70 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primerD.S.R. Item No. 13.41.1 |
| 71 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)D.S.R. Item No. 10.15.1 |
| 72 | Antiskid tilesProviding and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08 and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size600 x 600 mm (Make : Simpolo/Johnson)DSR 11.41A.3.1 |
| 73 | Extra for grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm dsr 11.48.2 |
| 74 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick.D.S.R. Item No. 11.26.1 |
| 75 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Make : Simpolo/Johnson)DSR 8.31 |
| 76 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels plain white marble/ udaipiur green marble / zebra balck marble area of slab over 0.50 sqmD.S.R. Item No. 8.2.2.2 |
| 77 | Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete.DSR 9.77 |
| 78 | Supply & Fixing of 150mm dia PVC pipe 6Kg per cm Square Pressure.Make : Astral, Prince, Kissan. RatePSR |
| 79 | Providing & laying cement concrete 1:5:10 (1 cement : 5 coarse sand :10 graded stone aggregate 40mm nominal size) alround PVC pipes including bed concrete as per standard design.D.S.R. 2023 Item No. 19.2.2 |
| 80 | Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :D.S.R. 2023 Item No.18.33 |
| 81 | Brick work in foundation 1st class b/work in 1:4cement and couarse sand mortar in fdn and plinth incl. supply of all materials , labour and t& P required for proper completion of the workAnalysed Rate |
| 82 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)RCC Work for Raft Footing, Drain Walls, Culverts Slab.D.S.R. Item No. 5.1.2 |
| 83 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, plascing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. D.S.R. Item No. 5.22.6 |
| 84 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.300 mm diaD.S.R. Item No. 23.1.1.1 |
| 85 | Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size diaD.S.R. 2023 Item No. 23.4.3 |
| 86 | Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. D.S.R. 2023 Item No. 23.7 |
| 87 | Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.D.S.R. 2023 Item No. 23.5 |
| 88 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality Circular shape 560 mm internal diameterL D- 2.5D.S.R. 2023 Item No. 19.19.3.1 |
| 89 | Providing & Fixing of Footrest making with 1.40meter long mild steel bar of 20mm diaAnalysis |
| 90 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.D.S.R. Item NO. 23.1.1.3 400 mm dia |
| 91 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level.D.S.R. Item No. 23.2.1.3, 400mm dia |
| 92 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size diaD.S.R. Item No. 23.3.3 |
| 93 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.D.S.R. Item No. 23.8 |
| 94 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.D.S.R. Item No. 23.12 |
| 95 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of : 200 mm diaD.S.R. Item No. 23.13.3 |
| 96 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.D.S.R. Item No. 23.14.3 |
| 97 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia.D.S.R. Item No.23.15.3 |
| 98 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 50 mm dia nominal boreD.S.R. Item No. 18.12.6 |
| 99 | Providing and fixing gun metal gate valve with C.I. wheel of approvedquality (screwed end) D.S.R. Item No.18.17.4 |
| 100 | Supply of 100mm dia Johnson screen.Kirlosker/CromptonP..S. |
| 101 | Supply of submersible pump of make KSB 3.00 HP with control panel, support wire etc. complete.Kirlosker/CromptonP.S. |
| 102 | Supply and fixing of finolex of copper cable ISI marked submersible cable of size 6 sq mmMake : Astral/Polycab/HavellsP.S. |
| 103 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white plastic seat and lidMake: JaquarD.S.R. Item No. 17.2.1 |
| 104 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.Make: JaquarD.S.R. Item No. 17.7.4 |
| 105 | Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.Semi rigid pipe : 32mm diaMake : Finolex/AstralD.S.R. Item No. 17.28.1.1 |
| 106 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. D.S.R. Item No. 17.31 |
| 107 | Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal boreMake : JaquarD.S.R. Item No. 17.16A |
| 108 | Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms.Make: JaquarD.S.R. Item No. 17.71 |
| 109 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.110mm diameterMake : Finolex/AstralD.S.R. Item No. 12.41.2 |
| 110 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm Make : Finolex/AstralD.S.R. Item No. 12.43.2 |
| 111 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.Make : Finolex/AstralD.S.R. Item No. 12.44 |
| 112 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 20mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.7.2 |
| 113 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.7.3 |
| 114 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.Concealed work including cutting chases and making good the walls etc.15mm dia nominal outer dia pipesMake : Finolex/AstralD.S.R. Item No. 18.8.1 |
| 115 | 20mm dia nominal outer dia pipesD.S.R. Item No. 18.8.2 |
| 116 | 25mm dia nominal outer dia pipesD.S.R. Item No. 18.8.3 |
| 117 | Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions15mm nominal bore.D.S.R. Item No.18.21.2.1 |
| 118 | Providing & fixing CP brass bib cock of approved quality conforming to IS 893115mm nominal boreMake : JaquarD.S.R. Item No. 18.49.1 |
| 119 | Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal boreMake : JaquarD.S.R. Item No. 18.53.1 |
| 120 | Providing and fixing gun metal gate valve with wheel of approved quality.25mm dia nominal boreMake : JaquarD.S.R. Item No. 18.17.1 |
| 121 | Providing and fixing gun metal gate valve with wheel of approved quality.20mm dia nominal boreMake : JaquarD.S.R. Item No. 18.17.1A |
| 122 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete. 25 mm nominal bore Make : Jaquar D.S.R. Item No. 18.18.3 |
| 123 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Make : Finolex/AstralD.S.R. Item No. 18.48 |
| 124 | Providing & laying PVC Pipe 100mm diameterMake : Finolex/AstralPWD SOR 730A |
| 125 | Providing & laying PVC Pipe 150mm diameterMake : Finolex/AstralPWD SOR 730B |
| 126 | Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.100mm diameter S.W. PipeD.S.R. Item No. 19.2.1 |
| 127 | 150mm diameter S.W. PipeD.S.R. Item No. 19.2.2 |
| 128 | Providing and fixing square mouth S.W. Gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design: 150 x 100 mm. size P type With Sewer bricks conforming to IS : 4885D.S.R. Item No. 19.4.1 |
| 129 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Range of four half stall urinals with 10 litre P.V.C. automatic flushing cistern.Make : JaquarD.S.R. 17.5.4 |
| 130 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board510x1040 mm bowl depth 250 mmD.S.R. Item No. 17.10.1.1 |
| 131 | Supplying and fixing of semi circle foam fountain with all necessary equipments(including Nozzle, Light, SMPS, Submersible pump, RGB controller, GI Ring, 1mm four core) all as per direction of Engineer in charge ( Analysed rate)Make : Premiere Fountain |
| 132 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.10.3 Electrical 2025 |
| 133 | Wiring for circuit/sub-main wiring along with earth wire with the following size of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-Charge 2X1.5 sqmm +1x1.5 sqmm earth wire D.S.R. Item No. 1.14.1 Electrical 2025 |
| 134 | 2X2.5 sqmm + 1x 2.5 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.2 Electrical 2025 |
| 135 | 2X4.0 sqmm + 1x 4.0 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.3 Electrical 2025 |
| 136 | 2X6.0 sqmm + 1x 6.0 sqmm earth wireMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.14.4 Electrical 2025 |
| 137 | Supplying and drawing co-axial TV cable RG-6 graded, 0.7 mm solid copper conductor PE insulated,shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.19 Electrical 2025 |
| 138 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. TV antenna socket outletMake: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.24.7 Electrical 2025 |
| 139 | Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-Charge D.S.R. Item No. 1.25 Electrical 2025 |
| 140 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.Make: Schneider/Jaquar /Northwest or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 1.26 Electrical 2025 |
| 141 | Supplying and fixing following size/modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module(75mm X 75 mm )D.S.R. Item No. 1.27.1 Electrical 2025 |
| 142 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch,connection etc. as required.D.S.R. Item No. 1.31 Electrical 2025 |
| 143 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,connection etc. as required. D.S.R. Item No. 1.32 Electrical 2025 |
| 144 | Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/woodedn block including connectionetc. as required. D.S.R. Item No. 1.33 Electrical 2025 |
| 145 | Supplying and fixing brass batten/angle holder including connectionetc. as required.D.S.R. Item No. 1.34 Electrical 2025 |
| 146 | Instalation,testing & commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLSCFL/LED lamps per fitting, complete with all accessories including connection etc. as required.D.S.R. Item No. 1.35 Electrical 2025 |
| 147 | Installation, testing and commissioning of prewired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. PVC insulated, copper conductor, single core cable etc. as required. D.S.R. Item No. 1.41 Electrical 2025 |
| 148 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.D.S.R. Item No. 1.45 Electrical 2025 |
| 149 | Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.D.S.R. Item No. 1.49 Electrical 2025 |
| 150 | Installation of exhaust fan in the existing opening, including making good the damage, connections, testing, commissioning etc. as required. upto 450 mm sweep.D.S.R. Item No. 1.50.1 Electrical 2025 |
| 151 | Extra for fixing the louvers / shutters complete with frame fro exhaust fans of all sizes. D.S.R. Item No. 1.51 Electrical 2025 |
| 152 | Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, `C` curve including connections, painting etc. as required.D.S.R. Item No. 1.57 Electrical 2025 |
| 153 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Disect Current(BLDC) motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value(CM/M/W) minimum 6, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per IS: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise= 75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.Make: Schneider / Crompton / Bajaj / or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 9.2.3 Electrical 2025 |
| 154 | Supplying and fixing following way, single pole and neutral sheet steel, MCB distribution board, 240 V on surface /recess complete with , tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge 12 way, Double doorD.S.R. Item No. 2.3.3 Electrical 2025 |
| 155 | Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' series, miniature circuit breaker (MCB) suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single PoleD.S.R. Item No. 2.10.1 Electrical 2025 |
| 156 | Double Pole Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single PoleD.S.R. Item No. 2.10.3 Electrical 2025 |
| 157 | 6 Way TPN Make: Schneider/MDS Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-Charge Single Pole D.S.R. Item No. 2.24.2 Electrical 2025 |
| 158 | Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.Make: Legrand / Schneider Electric / ABB / or equivalent make as per the direction of Engineer-in-ChargeSingle PoleD.S.R. Item No. 2.11 Electrical 2025 |
| 159 | Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc, with charcoal/cock and salt as required. Make: As approved in U.P.P.W.D & C.P.R.I.D.S.R. Item No. 5.4 Electrical 2025 |
| 160 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) D.S.R. Item No. 5.9 Electrical 2025 |
| 161 | Supplying and Laying of 6 SWG G.I wire at 0.50 metre below ground level for conductor earth electrode, including connection / terminating with G.I. thimble etc. as required.Make: As approved in U.P.P.W.D & C.P.R.I.D.S.R. Item No. 5.7 Electrical 2025 |
| 162 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mmMake: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.10.7.1 Electrical 2025 |
| 163 | Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sqmm. (19mm) Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No. 11.1.2 Electrical 2025 |
| 164 | Supply of following size of 1.1 KV grade multicore aluminium conductor PVC sheathed armoured cable as per IS 1554.16 sq. mm 4 core PWD SOR 501(i)Make: Polycab / Finolex/RR Kabel or equivalent make as per the direction of Engineer-in-Charge |
| 165 | Supplying, Installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operatingvoltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -50C to 400C, internal surgeprotection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80,UGR (Unified Glare Rating) < 19, Flicker free (flicker should be below 5%), life time (LED, Driver &electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained tilllife ends, CCT 3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be confirming to relevant BIS standards. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc.as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Wattoutput . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall besubmitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trimBGSLO Sleek Recess RD 9W WH LEDMake: Bajaj / Jaquar / Go Green or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.8.1.2 Electrical 2025 |
| 166 | LED Batten light (System lumen efficacy >135lm/Watt) Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140- 270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard DeviationColor Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted.. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) 18- 22 WattMake: Bajaj / Jaquar / Go Green or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.8.11.1 Electrical 2025 |
| 167 | S/f of 340 mm wide x 101.6 mm deep(3.0\\") Concealed Box PWD SOR Item No. 1151c |
| 168 | LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt)Supplying, installation, Testing & Commissioning of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. Complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5-year OEM warranty. System lumen efficacy >135 lm/Watt output. LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in- Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm) LED Sqaure Ceiling light 24Watt.BPSLR Surface 24W LED WH SQ SDMake: Bajaj / Jaquar / Go Green or equivalent make as per the direction of Engineer-in-ChargeD.S.R. Item No.8.8.3 Electrical 2025 |
| 169 | Supply of 300mm dia sweep PVC body, 900±10% RPM Exhaust fan with guard and mounting arrangement.300mm sweep. Make: Bajaj / Usha/Atomberg |
| 170 | Providing, supplying, installing, testing and commissioning recessed LED downlight (12W, warm white, 3000K, die-cast aluminium body, IP20, BIS approved, Philips/Schneider/Wipro/Crompton or equivalent), complete with driver and all accessories.Make: Bajaj / Jaquar / Go Green |
| 171 | Providing, supplying and fixing 7/9 Watt LED Bulb, suitable for 230 V, 50 Hz AC supply, with required holder/base and all necessary accessories, including removal/replacement of existing bulb wherever required, connection, testing and commissioning, complete in all respects as per specifications and direction of Engineer-in-Charge.Make: Bajaj / Jaquar / Go Green |
| 172 | Providing and fixing recessed COB LED spotlight (7W–12W, adjustable beam, warm white) for feature walls and decorative panels, complete.Make: Bajaj / Jaquar / Go Green |
| 173 | SUBHEAD V-MAIN L. T. PANELSPANELSupply, installation, testing and commissioning of electrical panel, modular type, front accessible only, free floor standing confirming to Minimum IP:43 degree of protection. The panel sheet structure shall undergo seven tank pre-treatment process before painting. The sheet steel shall be all of 2.0mm thick CRCA sheet. All the openable compartments of the panel shall be completely shrouded and provided with padlocking arrangement on all compartments including bus bar and cable alley chambers. The panel height shall not exceed 2200mm and the maximum operating height for any switchgear shall not be more than 1700mm. The panel shall be provided with minimum 75mm base channel frame fabricated from ISMC sections. All bus bar links in the panel shall be solid bus bars with coloured PVC shrinkable sleeves, no wires will be acceptable. Continuous earth bus shall run alround the panel with earthing studs provided at minimum 2 places. The control wiring shall be carried out with minimum 1.5/2.5 sqmm copper wires and adequate number of NO/NC, potential free contacts incorporated for remote operation of the starters. Proper sized cable termination gland plates shall be provided on cable alleys and knockouts for same shall be provided during fabrication stage itself. The panel shall be provided with a thermostatically controlled heating arrangement (200 W) to take care of high humidity conditions. A 5A socket service outlet (single phase) shall be provided in one of the compartments as ervice outlet in the panel. Panel shall be so designed at to have minimum 20% spare feeders/space. Panel shall undergo epoxy powder coated paint, colour as per IS:5 requirement. All cable terminations shall be from top. The complete panel shall be fuse less type, for control circuits 2A/6A MCB's to be used.All bus bars shall be of aluminium, electrolytic grade only. Maximum design density shall not exceed 1 Amps/Sqmm. All bus bars shall be insulated with coloured heat shrinkable PVC sleeved. All bus bar supports shall be non hygroscopic DMC/SMC supports.The panel shall be manufactured in conformance to requirements of local electrical inspector and it shall be contractors responsibility to get initial approval of drawings and also final approval of complete electrical works related to this section. Make:Schneider/Jaquarl/Northwest The minimum clearances between bus bars shall be as follows : Phase to phase - minimum 20mm Phase to neutral-minimum 15mm mtr PANELIncoming : One (1) No 100 Amp. 4P MCCB of 25KA Breaking capacity mtring : One (1) No. Sets Multifunction mtr nos incoming One (1) No. of Phase Indication Lamp nos incoming Bus Bar : One (1) No. 150 Amp.TPN aluminimum bus bar of suitable length.Outgoing : Phase indication lamps on nos outgoing to be provided. 01 No.63 Amp 4P MCB. (10 KA) 19 No.63 Amp DP MCB. (10 KA) 02 No.40 Amp DP MCB. (10 KA)Panel described as above. N.S |
| 174 | EXTERNAL ELECTRICAL WORKSSCHEDULE ITEMS (AS PER P.W.D. SOR Item No. 2022 SCHE. 2018/DSR 2018)NON - SCHEDULED ITEMS (AS PER MARKET RATES )SUB-HEAD-I (SUBSTATION EQUIPMENTS)TRANSFORMER100KVA 11KV/433V Dyn11 Copper Wound Oil Type Transformer with OCTC +5% to -10% in steps of 2.5% , Class of Insulation: A, Temperature rise limits of 40 deg.C over ambient of 50 degrees. Losses (As per IS tolerances) No load losses -2.7kW, Full load losses - 7.7kW and all accessories and confirming to As per IS 1180 Level 2 & Testing paramtr as per IS 2026 complete with all fittings and accessories as per specifications attached etc as required at site.N.S. (P.S.) |
| 175 | H.T. VCB (11KV) (P.S.)Design, manufacturing, testing at works, supply of HT Panel as per specification and comprising of the following :-a. INCOMER630 A Vacuum circuit breaker of 26.3 KA ruputuring capacity at 11 KV rated, totally enclosed,air insulated metal clad housing, floor mounting, vertical isolation,vermin proof,fully interlocked horizontal drawout type having double isolation.Manually and motor operated, spring charged( release closing mechanism) trip free type,triple pole truck mounted draw out, vacuum circuit breaker, incorporating mechanical as well as electrical ON/OFF indication. Spring charge/discharge mechanical indicator.630 amp air insulated but encapsulated,PVC insulated Copper bus bars.C.T. chamber with C.T.'s 40/5.15 VA burden for protection (class 5P 10).Following protection shall be provided:1 Nos IDMT relay with instantaneous 2 nos. over currrent (50, 50 N) element and 1 no. instantaneous earth fault element(50-50N).(O/C setting 50%-200% and E/F setting 20%-80%)All wiring necessary for the above including inter-connections. The size of the conductor should not be less than 2.5 sq. mm. Copper wire where required. Test terminal block, fuses/2A SPMCB , circuit labels,set of phase, indication lamps etc. as per standard practise as under.Red - Breaker close (ON)Green - Breaker open (OFF)Amber - auto tripClear - trip circuit healthywhite - 3 nos. one per phaseControl :- T-N-C (Trip, Neutral. Close) breaker control switch with indication arrangement.Blue spring chargedTerminal boxes with single gland trifucating cable box suitable for 11 KV Aluminium XLPE (E) cable of size 3C x 150 Sq. mm. for incoming/outgoing breaker.HT Danger Plate.(as per IS specification)2 Runs of 40 X 5 mm earth bus shall be provided for the full length of the panel.Power Pack, Battery power pack shall be rated for minimum five (5) trippings. For DC power one no. source selector switch to be incorporated i.e. one source from power pack and other from outside.Necessary D.C. supply healthy indication lamp (White Colour), switch with alarm.Surge supressor as required.DC Voltmtr, 0-30 Volt, Digital type.HT Panel switchboard complete with all interconnections, labels, wiring etc, complete as described above in item nos.A and B and as per specifications.N.S. |
| 176 | Providing, supplying and fixing of EDGAR LIGHT 3.5 m high decorative pole with RUBUS 27W LED luminaire, complete with all necessary fittings and accessories, of approved make BAJAJ, including 3.5 m high pole of suitable material and finish, LED luminaire, mounting arrangement, base plate, anchor bolts, nuts, washers, brackets, cable entry arrangement, internal wiring, junction box, termination, earthing connection, erection, alignment, grouting/fixing of pole in suitable foundation, testing and commissioning, including all labour, tools, tackles, transportation, loading, unloading and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj/Go Green/JaquarModel/Type: Edgar Light – 3.5 m DA Pole with RUBUS 27WLight: RUBUS 27W LEDHeight: 3.5 mUnit: Each (No.)Market Rate |
| 177 | Providing, supplying and fixing TULIP LIGHT 25W DA MARCUS 3.0 m high decorative pole, complete with all necessary fittings and accessories, of approved make, including 25W LED luminaire, 3.0 m high decorative pole, mounting/bracket arrangement, base plate, anchor bolts, nuts, washers, cable entry, internal wiring, junction/terminal box, earthing connection, fixing in suitable foundation with cement concrete, grouting, erection, alignment, testing and commissioning, including transportation, loading, unloading, labour, tools, tackles and all incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Light Type: Tulip LightLuminaire: 25W LEDPole: DA Marcus, 3.0 m heightUnit: Each (No.)Make: Bajaj/Go Green/JaquarMarket Rate |
| 178 | Providing, supplying and fixing ALGARVE LED BOLLARD LIGHT of approved make and model, complete with all necessary fittings and accessories, including LED bollard luminaire, suitable mounting/fixing arrangement, base plate, anchor fasteners, nuts, washers, cable entry, internal wiring, junction/terminal arrangement, earthing connection, suitable RCC/PCC foundation, grouting, erection, alignment, testing and commissioning, including transportation, loading, unloading, labour, tools, tackles and all incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Product: Algarve LED Bollard LightType: LED Outdoor Bollard LightMake: Approved makeWattage: As per approved manufacturer/modelUnit: Each (No.) |
| 179 | Providing, supplying and fixing 4.0 m high TRINGA Column Light with remote control, TRI-Colour Light Column, Model BLSLC 50W LED TRI 4M, of approved make BAJAJ, complete with all necessary fittings and accessories, including 50W LED tri-colour luminaire, 4.0 m high decorative column/pole, remote-control arrangement, LED driver/control gear, mounting brackets, base plate, anchor bolts, nuts, washers, cable entry, internal wiring, junction/terminal box, earthing connection, fixing/erection on suitable RCC/PCC foundation, grouting, plumbing and alignment, testing and commissioning, including transportation, loading, unloading, labour, tools, tackles and all incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: BajajModel: BLSLC 50W LED TRI 4MType: Tringa Column Light / Tri-Colour Light ColumnHeight: 4.0 mWattage: 50W LEDControl: Remote ControlUnit: Each (No.) |
| 180 | Providing, supplying and fixing LED Spike/Bush Light, SPYKZ, Model BGSBL 9W LED WW, 9W LED, Warm White 3000K, with die-cast aluminium housing designed for rugged outdoor usage and IP65 protection, of approved make BAJAJ / Go Green / Jaquar or equivalent approved make, complete with LED luminaire, integral/compatible LED driver, adjustable mounting bracket with spike, fixing accessories, electrical connection, cable termination, earthing, testing and commissioning, including all labour, tools, tackles, transportation, loading, unloading and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj / Go Green / JaquarPreferred Make: BajajModel: SPYKZ – BGSBL 9W LED WWWattage: 9WCCT: 3000K Warm WhiteHousing: Die-cast aluminiumProtection: IP65Type: LED Spike / Bush LightUnit: Each (No.) |
| 181 | Providing, supplying and fixing Wall Focus Light, BAJAJ AMAZE, Model BJFL 50W LED I, 50W LED floodlight, 5700K, having toughened glass, pressure die-cast aluminium housing, IP66 ingress protection and suitable mounting arrangement, complete with LED driver/control gear, wall-mounting MS/GI bracket, anchor fasteners, nuts, bolts, washers, cable entry, internal wiring, junction/terminal arrangement, electrical connection, earthing, aiming and alignment, testing and commissioning, including all labour, tools, tackles, transportation, loading, unloading and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj / Go Green / Jaquar Model: AMAZE – BJFL 50W LED IWattage: 50W LEDCCT: 5700KType: LED Floodlight / Wall Focus LightHousing: AluminiumFront Cover: Toughened glassProtection: IP66Unit: Each (No.)Market Rate |
| 182 | Providing, supplying and fixing 30W Static White MERC Square Projector Light, Item Code BA SP B 120W (WHWW), of approved make BAJAJ / Go Green / Jaquar or equivalent approved make, complete with LED projector luminaire, LED driver/control gear, die-cast aluminium housing, suitable mounting bracket/adjustable aiming arrangement, anchor fasteners, nuts, bolts, washers, cable entry, internal wiring, junction/terminal arrangement, electrical connection, earthing, fixing, aiming and alignment, testing and commissioning, including all labour, tools, tackles, transportation, loading, unloading and all necessary accessories and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj / Go Green / Jaquar Type: MERC Square Projector LightSpecified Wattage: 30W Static WhiteItem Code: BA SP B 120W (WHWW) — to be verified against approved manufacturer's datasheetLight Colour: Static WhiteUnit: Each (No.) |
| 183 | Providing, supplying and fixing BA 50W RGBW MERC Square Projector Light of approved make BAJAJ / Go Green / Jaquar or equivalent approved make, complete with LED projector luminaire having RGBW colour-changing facility, LED driver/control gear, die-cast aluminium housing, suitable optical assembly, adjustable mounting bracket, anchor fasteners, nuts, bolts, washers, cable entry, internal wiring, junction/terminal arrangement, electrical connection, earthing, fixing, aiming and alignment, testing and commissioning, including all labour, tools, tackles, transportation, loading, unloading and all necessary fittings, accessories and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj / Go Green / Jaquar or equivalent approved makePreferred Make: BajajType: MERC Square LED Projector LightWattage: 50WLight Source: RGBW / RGB + WhiteColour Control: RGB colour-changing with white light facilityHousing: Die-cast aluminiumMounting: Adjustable surface/floodlight mounting bracketUnit: Each (No.) |
| 184 | Providing, supplying, erecting, testing and commissioning of 30W All-in-One (AIO) LED Solar Street Light (Hybrid), Model 30W-SOLAR BSZSL 30W LED HYB-STANDARD HYBRID, of approved make BAJAJ / Go Green / Jaquar or equivalent approved make, complete with high-efficiency solar photovoltaic module, rechargeable battery, MPPT/PWM solar charge controller, LED luminaire, integrated control electronics, automatic dusk-to-dawn operation, suitable battery backup, 5.0 m high octagonal galvanized steel pole, pole top/bracket, foundation bolts, base plate, RCC/PCC foundation, cable/connectors, internal wiring, earthing, installation, testing and commissioning, including transportation, loading, unloading, labour, tools, tackles and all other necessary fittings, accessories and incidental works, complete in all respects as per manufacturer's specifications and direction of Engineer-in-Charge.Make: Bajaj / Go Green / Jaquar or equivalent approved makePreferred Make: BajajModel: 30W-SOLAR BSZSL 30W LED HYB-STANDARD HYBRIDType: All-in-One LED Solar Street Light – HybridLED Power: 30WPole: 5.0 m high octagonal steel poleSystem: Solar PV + Battery + Hybrid control systemOperation: Automatic dusk-to-dawnUnit: Each (No.) |
| 185 | Providing, supplying, installing, testing and commissioning Bajaj PRAZE LED Floodlight, Model PRAZE F 210L WH NB-A5 TG SD, 150W, 5700K, with pressure die-cast aluminium housing, toughened glass, secondary lens optics, IP66 protection and suitable narrow/medium beam optical arrangement, complete with LED driver/control gear, mounting bracket, clamps, anchor fasteners, nuts, bolts, washers, electrical cable connection, cable glands, lugs, termination, earthing and aiming/alignment, including all labour, tools, tackles, transportation, loading, unloading and incidental works, complete in all respects as per manufacturer's specifications, approved lighting design and direction of Engineer-in-Charge.Make: BajajModel: PRAZE F 210L WH NB-A5 TG SDWattage: 150WCCT: 5700KType: LED FloodlightHousing: Pressure die-cast aluminiumFront: Toughened glassProtection: IP66Beam: NB-A5, approx. 60°Unit: Each (No.) |
| 186 | Supply & fixing of 9 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 155 mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.PWD SOR 2024 ELEC. ITEM NO. 645 |
| 187 | SUB-HEAD-XVI: IT/ NETWORKING, & CCTV SYSTEM-ACTIVE & PASSIVE COMPONENTPASSIVE COMPONENT( STRUCTURED CABLING SYSTEM PASSIVE) Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG solid copper conductors for Connectivity of Hub room to End Point. Approved Makes: Belden/Siemon/Panduit/Derwiser/ Rit |
| 188 | Supply, Installation, Testing & Commissioning of CAT6 information outlet (I/O) for Data, Voice, Wifi and Camera at user end.Approved Makes: Belden/Siemon/Panduit/Derwiser/ Rit |
| 189 | Supply, Installation, Testing & Commissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination at rack end. |
| 190 | Supply, Installation, Testing & Commissioning of CAT6 patch cord 3 feet for rack side switch to jack panel connectivity. |
| 191 | Supply, Installation, Testing & Commissioning of CAT6 patch cord 7 feet for information outlet (I/O) to end user device connectivity. |
| 192 | Supply, Installation, Testing & Commissioning of 1, 2 and 4 port face plate white for I/O fixing at user side. |
| 193 | Supply, Installation, Testing & Commissioning of 42 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. |
| 194 | Supply, Installation, Testing & Commissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts. |
| 195 | Supply, Installation, Testing & Commissioning of of Access Switch 24 Port POE+ Access Switches with switching capacity of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4 x 10G SFP+ uplink ports, should have support for 9 switch Stacking with bandwidth of minimum 120 Gbps. Should support min 2GB internal DRAM, 2GB internal Flash memory, 32K MAC address, 4k Multicast Routes, Should have static Routing from day 1 and upgradable to support OSPF and VRRP with 1 year support. Make: Bose/Bosch/Honeywell |
| 196 | SUB-HEAD-XVII: IP CCTV SYSTEMSupply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support upto 128GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : line crossing , perimeter intrusion ,Face detection(deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 40 meters , IP 67 , IK10 ,POE.Make: Bose/Bosch/Honeywell |
| 197 | Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : line crossing , perimeter intrusion ,Face detection (deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 50 meters , IP 67 , IK 10 housing , POE.Make: Bose/Bosch/Honeywell |
| 198 | Supply, installation, testing and commissioning of 64 channel NVR , ONVIF compliant , recording bandwidth 640 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ45 ethernet , iOS smartphone support , 8 HDD support , each HDD slot support upto 8 TB HDD , RAID support , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse .Edge analytics of poposed cameras must be integrated with NVR . Artificial Intelligence Support having face recognition with compatible deep learning supported cameras, AI-Face registered quantity upto 10,000 ,A.I maximum captured quantity 200,000. . UL,CE,FCC certified.Make: Bose/Bosch/Honeywell |
| 199 | Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk. Make: WD/Sandisk/Seagate |
| 200 | Supply, Installation, Testing and Commissioning of Full HD 55\\" LED Professional Display Panel. Sony/Panasonic/Samsung |
| 201 | Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7- Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5\\" SATA 6Gb/s Hard Drive; Operating system: Windows 11 Professional 64 Bit or latest |
| 202 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 25mm diaD.S.R. Item No. 1.21.2 |
| 203 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32mm diaD.S.R. Item No. 1.21.3 |
| 204 | Supply, Installation, Testing and Commissioning of LCD / LED monitor capable of displaying the output of the CCTV system in the location specified at site- 31.5 inches TV with KVMsplitter & HDMI cable.Make: Sony/Samsung/LG |
| 205 | Poviding & Fixing Designer dust bin Monkey type with all fitting & acces. required for complition of job complete.(P.S.) |
| 206 | Providing, Fixing Horse Rider (Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play (SKU: OKP_STA_024) or equivalent as aproved by engineer in charge.Market Rate |
| 207 | Providing & Fixing Fish Rider (Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play (SKU: OKP_STA_029) or equivalent as aproved by engineer in charge.Market Rate |
| 208 | Providing & Fixing MERRY GO ROUND (Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play or equivalent as aproved by engineer in charge.Market Rate |
| 209 | Providing & Fixing MONKEY BAR-SIMPLE (Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play (SKU: OKP_STA_009) or equivalent as aproved by engineer in charge.Market Rate |
| 210 | Providing & Fixing PLAY 2 SEATER SEA-SAW(Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play SKU: OKP_STA_017 or equivalent as aproved by engineer in charge.Market Rate |
| 211 | Providing & Fixing SWING-A-ONE(Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete.Make: Okay Play ( | ECONOMY MODEL – 8 SKU: OKP_STA_014) or equivalent as aproved by engineer in charge.Market Rate |
| 212 | Providing & Fixing two way Slider (Made from non toxic durable LLDPE and plastic material, Adjustable height suitable for both indoors & outdoors, weather resistant & waterproof, Anti oxidation, Anti slip base & Anti UV) with all fitting & acces. required for complition of job complete. Make: Okay Play (FUNSTATION ECONOMY MODEL – 14, SKU: OKP_EMS 14) or equivalent as aproved by engineer in charge.Market Rate |
| 213 | Providing & Fixing two way Slider PLAYSTATION with all fitting & acces. required for complition of job complete. Make: OK PLAY MEADOW SKU: OKP_NP2 or equivalent as aproved by engineer in charge.Market Rate |
| 214 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).D.S.R. 2025 Item No. 2.1 |
| 215 | Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).D.S.R. 2025 Item No. 2.2 |
| 216 | Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% forpayment).D.S.R. 2025 Item No. 2.3 |
| 217 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) :D.S.R. 2025 Item No. 2.4.1 Screened through sieve of I.S. designation 20 mm |
| 218 | Supply & plantation of Trees upto 8ft to 10ft height well settled, all indigenous varieties (local) as per listed below, location and quantities shall be as per drawingMangifera Indica (Mango), Bacopa Monnieri (Brahmi), Terminalia Tomentosa (Asna), Azadirachta Indica (Neem) & Bambusa Bambos (Baans)Terminalia Arjuna (Arjun), Tectoria Grandis (Sagaun), Shorea Robusta (Saal), Stereospermum Tetragonum (Padal), Anogeissus Latifolia (Bakli), Madhuca Longifolia (Mahua) & Diospyros Malabarica (Gaub) Saraca asoca (ashok), Ficus religiosa (peepal), Ficus benghalensis (bargad), Aegle marmelos (bel) & Phyllanthus emblica (aonla) Pterocarpus Santalinus (rakta chandan), Butea monosperma (dhaak), Artocarpus altilis (kathal) & Santalum album (chandan) Saraca Asoka (Sita Ashok), True Cinnamon (Nag Kesar), Mangolia Champaca (Champa) & Mimusops Elengi (Maulsari) Saussurea Ggossypiphora (Mratyusanjeevani), Azadirachta Indiac (Neem) & Adiantum Venustum (Hansraj) |
| 219 | Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area. (two application) i/c cost of chemical) and as per direction of officer-in-charge.and as per directionof officer-in-charge.D.S.R. 2025 Item No. 2.56 |
| 220 | Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge. D.S.R. 2025 Item No.2.33 |
| 221 | Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately) D.S.R. 2025 Item No. 2.13 |
| 222 | Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment).D.S.R. 2025 Item No. 2.25 |
| 223 | Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. D.S.R. 2025 Item No. 4.88 |
| 224 | Providing and Displaying Budded Rose (H.T. variety) 3 to 4 healthy branch 30 cm and above ht. well developed with one and above flower plant in 20 cm Earthen Pot, as per direction of the officer-in-charge. D.S.R. 2025 Item No. 4.91 |
| 225 | Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge. D.S.R. 2025 Item No. 5.13 |
| 226 | Providing and Displaying Cyprus golden well shaped developed with good colored foliage fresh & healthy 60 to 75 cm ht in 30 cm Earthen Pot as per direction of the officer-in-charge. D.S.R. 2025 Item No. 5.17 |
| 227 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge. D.S.R. 2025 Item No. 5.28 |
| 228 | Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. D.S.R. 2025 Item No. 6.1 |
| 229 | Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. D.S.R. 2025 Item No. 6.3 |
| 230 | Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. D.S.R. 2025 Item No. 6.10 |
| 231 | Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 6.14 |
| 232 | Providing and stacking of Ophiopogon jaburan (variegated) ,full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. D.S.R. 2025 Item No. 6.21 |
| 233 | Providing and stacking of Alstonia scholaris of height 150-165 cm. in bagof size 25 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 7.4 |
| 234 | Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 7.13 |
| 235 | Providing and stacking of Cassia siamea of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 7.17 |
| 236 | Providing and stacking of Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 8.2 |
| 237 | Providing and stacking of Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.7 |
| 238 | Providing and stacking of Cassia laevigata of height 45-60 cm. in earthenpots of size 20 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 8.11 |
| 239 | Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 8.14 |
| 240 | Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 8.54 |
| 241 | Providing and stacking of Allamanda violacea of height 30 cm to 45 cm. in poly bag of size 20 cm as per direction of the officer-in-charge. D.S.R. 2025 Item No. 9.2 |
| 242 | Providing and stacking of Clerodendrum thomsoniae of height 30 cm.to 45 cm in 20 cm size of poly bag & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 9.6 |
| 243 | Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. D.S.R. 2025 Item No. 9.14 |
| 244 | Providing and Stacking of Aprajita Blue well developed in poly bag of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 11.17 |
| 245 | Providing and Stacking of Aprajita White well developed in poly bag of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 11.18 |
| 246 | Providing and displaying of Aglaonema Snow-White hybrid (three in one), having ht. 30 cm & above with 6 to 8 leaves, bright colour, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot. (Specimen ) & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.4 |
| 247 | Providing and displaying of Araucaria cookie having ht. 75 cm to 90 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.14 |
| 248 | Providing and displaying of Araucaria cookie having ht. 1.20 cm to 1.50 cm, straight, well developed, fresh and healthy with lush green leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.16 |
| 249 | Providing and Stacking of Ashwagandha of ht. 30 cm with multi branches in Poly bag of size 20 cm.as per direction of the officer-in-charge.D.S.R. 2025 Item No.11.3 |
| 250 | Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.D.S.R. 2025 Item No.9.9 |
| 251 | Providing and stacking of Jasmine grandiflorum (chameli) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.D.S.R. 2025 Item No.9.8 |
| 252 | Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of theofficer-in-charge.D.S.R. 2025 Item No. 5.12 |
| 253 | Providing and stacking of Plumeria acutifolia of height 120-135 cm. with 2-3 branches in HDPE bag of size 30 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.67 |
| 254 | Providing and stacking of Plumeria rubra of height 120-150 cm. with 2-3 branches in HDPE bag of size 30 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.72 |
| 255 | Providing and stacking of Tabernaemontana coronaria (Chandni single) veriegated of height 105-120 cm., multibranched, bushy in big size HDPE bag as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.63 |
| 256 | Providing and displaying of Livistona palm having ht. 60 cm to 75 cm, well developed with 8 to 10 leaves, fresh & healthy foliage in 30 cm size of Earthen pot/Plastic pot. as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.50 |
| 257 | Providing and displaying of Money Golden leaves mounted on moss stick 90cm ht., having 3 s at equal distance, well developed with full of fresh, shinning and healthy leaves from bottom to top in 25 cm size of Earthenpot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.54 |
| 258 | Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 6.10 |
| 259 | Providing and displaying of Croton golden (Broad Leaves) having ht. 60 cm to 75 cm with 3 to 4 branches, well developed, fresh and healthy leaves in 25 cm size of Earthen pot/Plastic pot. & as per direction of theofficer-in-charge.D.S.R. 2025 Item No. 3.27 |
| 260 | Providing and displaying of Croton Golden specimen having ht. 90 cm to 1.05 cm with 5 to 6 branches, well developed, fresh and healthy foliage in 30 cm size of Earthen pot/Plastic pot as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.28 |
| 261 | Providing and displaying of Croton Petra Bangalore variety having ht. 60 cm to 75 cm with 4 to 6 branches, well developed, fresh and healthy colorful leaves in 25 cm size of Earthen pot/Plastic pot & as per direction of theofficer-in-charge.D.S.R. 2025 Item No. 3.33 |
| 262 | Providing and Stacking of Curry leaf of height 75-90 cm in poly bag of size 25 cm as perdirection of the officer-in-chargeD.S.R. 2025 Item No. 11.2 |
| 263 | Providing and displaying of Dracaena Victoria having ht. 30 cm & above, well developed with full of leaves, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.46 |
| 264 | Providing and stacking of Cestrum nocturnum (Raat ki Rani) of height 60 75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.13 |
| 265 | Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.14 |
| 266 | Providing and displaying of Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.17 |
| 267 | Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge.D.S.R. 2025 Item No. 3.18 |
| 268 | Providing and Displaying Ficus Long Island topiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No. 5.21 |
| 269 | Providing and Displaying Ficus reginold well developed fresh & healthy foliage 60 to 75 cm spread 105 to 120 cm ht., Bushy in 35 cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No. 5.25 |
| 270 | Providing and stacking of Foxtail palm of ht. 120-150 cm bottom girth 15 20 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.42 |
| 271 | Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3 4 branches in earthen pots of size 20 cm as per direction of the officer-in-chargeD.S.R. 2025 Item No. 8.30 |
| 272 | Providing and Displaying Cyprus Golden Conical Shape 150 to 165 cm ht., with fresh and healthy Golden colour foliage in 35cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No. 5.18 |
| 273 | Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.24 |
| 274 | Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.54 |
| 275 | Providing and stacking of Hibiscus rosasinensis of height 90-105 cm., bushyin big size HDPE bag as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.37 |
| 276 | Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.D.S.R. 2025 Item No.6.29 |
| 277 | Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.7.48 |
| 278 | Providing and stacking of Bauhinia blakeana (Kachnar) Yellow of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.7.7 |
| 279 | Providing and Stacking of Karonda of ht. 45-60cm in Poly bag of size 25 cm. as per direction of the officer-in-charge.D.S.R. 2025 Item No.11.11 |
| 280 | Providing and Displaying Latania Rubra Palm well developed with fresh & healthy foliage 150 to 180 cm ht. with 6 to 7 leaves in big 35 cm Cement Pot as per direction of the officer-in-chargeD.S.R. 2025 Item No. 5.35 |
| 281 | Providing and stacking of Lagerstroemia flosreginae of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.50 |
| 282 | Providing and Stacking of Lemon grass of ht. 30cm with multi branches in Poly bag of size 20 cm. as per direction of the officer-in-charge.D.S.R. 2025 Item No. 11.10 |
| 283 | Providing and stacking of Pinus longifolia (Pinus) of height 90-105 cm. in cement pots of size 35 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 7.65 |
| 284 | Providing and stacking of Murraya Koenigii spreng (Kadipatta/meetha neem) of ht 45-60 cm well developed in earthen pots of size 20 cm. per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.47 |
| 285 | Providing and stacking of Melia azedarach (Bakayan) of height 120-135 cm. in big poly bag of size 25 cm as per direction of the officer-in-chargeD.S.R. 2025 Item No. 7.54 |
| 286 | Providing and Displaying Petunia hybrid different variety in different colour well developed with fresh and healthy foliage in full bloom in 25 cm Earthen Pot/Plastic Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No. 4.50 |
| 287 | Providing and stacking of Tabernaemontana divaricata (Chandni double) of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No. 8.64 |
| 288 | Providing and displaying of Phoenix palm having ht. 75 cm to 90 cm with 10 to 15 or more leaves, well developed, fresh and healthy in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.67 |
| 289 | Providing and stacking of Ficus infectoria (Pilkhan) of height 150-165 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.7.32 |
| 290 | Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-chargeD.S.R. 2025 Item No.7.70 |
| 291 | Providing and displaying of Raphis palm having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction ofthe officer-in-charge.D.S.R. 2025 Item No.3.70 |
| 292 | Providing and displaying of Raphis palm specimen having ht. 1.50 m to 1.65 m with 40 to 50 lush green suckers, well developed, fresh & healthy foliage leaves in 40 cm size of Earthen Pot/Chali/Tray & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.71 |
| 293 | Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.3 |
| 294 | Providing and Displaying of Rubber variegated, well developed, having 45 to 60 cm ht.with fresh, healthy leaves in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.90 |
| 295 | Providing and displaying of Dracaena song of India specimen (three in one), having ht. 60 cm & above, well developed, fresh and healthy with good foliage in 25 cm size of Earthen pot/Plastic pot & as per direction ofthe officer-in-charge.D.S.R. 2025 Item No.3.39 |
| 296 | Providing and stacking of Spathodea campanulata of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.7.82 |
| 297 | Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.6.8 |
| 298 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.28 |
| 299 | Providing of Schefflera Green (three in one), mounted on moss stick 90 cm, well developed with full of fresh & healthy leaves from bottom to top with rich foliage in 25 cm size of Earthen pot/Plastic pot.as per direction ofofficer-in-charge.D.S.R. 2025 Item No.3.78 |
| 300 | Providing and displaying of Schefflera Varieged, mounted on moss stick 90 cm ht., 3 to 4 s placed in each pot at equal distance, well developed with full of fresh & healthy bright leaves from bottom to top in 25 cm size ofEarthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.79 |
| 301 | Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.3.14 |
| 302 | Providing and stacking of Syngonium golden of height 30-45 cm. with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.D.S.R. 2025 Item No.6.26 |
| 303 | Providing and stacking of Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.D.S.R. 2025 Item No.8.69 |
| 304 | Providing and Displaying Travelers palm well developed with fresh & healthy foliage 120 to 150 cm ht. in 35 cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.42 |
| 305 | Providing and Displaying Travelers palm well developed with fresh & healthy leaves foliage 210 to 240 cm ht specimen in 40 cm Cement Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.43 |
| 306 | Providing and stacking of Washingtonia filifea palm stem ht. 120-135 cm with 8-10 healthy leaves lush green leaves well developed in big size HDPE Bags as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.44 |
| 307 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mmD.S.R. 2025 Item No.2.4.1 |
| 308 | Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.D.S.R. 2025 Item No.4.88 |
| 309 | Providing and Displaying Cyprus golden well shaped developed with good colored foliage fresh & healthy 60 to 75 cm ht in 30 cm Earthen Pot as per direction of the officer-in-charge.D.S.R. 2025 Item No.5.17 |
| 310 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-chargeD.S.R. 2025 Item No.5.28 |
| 311 | Providing and stacking of Alpinia Variegated (three in one) having ht. 30 cm and above, with fresh and healthy variegated foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.D.S.R. 2025 Item No.6.1 |
| 312 | Providing and stacking of Asparagus marrie, well developed 15 to 20 leaves, full of branches and foliage in 25 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-chargeD.S.R. 2025 Item No.6.3 |
| 313 | Providing and stacking of Cuphea chinensis of ht. 20-30 cm full of branches and healthy foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-chargeD.S.R. 2025 Item No.6.10 |
| 314 | Providing and stacking of Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..D.S.R. 2025 Item No.6.14 |
| 315 | Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge.D.S.R. 2025 Item No.6.21 |
| 316 | Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.8.14 |
| 317 | Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.8.54 |
| 318 | Providing and stacking of Allamanda violacea of height 30 cm to 45 cm. in poly bag of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.9.2 |
| 319 | Providing and stacking of Clerodendrum thomsoniae of height 30 cm.to 45 cm in 20 cm size of poly bag & as per direction of the officer-in-charge.D.S.R. 2025 Item No.9.6 |
| 320 | Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-chargeD.S.R. 2025 Item No.9.14 |
| 321 | Providing and Stacking of Aprajita Blue well developed in poly bag of size 20 cm as per direction of the officer-in-chargeD.S.R. 2025 Item No.11.17 |
| 322 | Providing and Stacking of Aprajita White well developed in poly bag of size 20 cm as per direction of the officer-in-charge.D.S.R. 2025 Item No.11.18 |
| 323 | IRRIGATION SYSTEMDRIP IRRIGATION SYSTEM FOR PLANTATION - ASYSTEM HEAD UNIT SNAD FILTER + BACKWASH ASSLY 2.5\\"P.S. |
| 324 | SCREEN FILTER 2.5\\"P.S. |
| 325 | ASSLY FOR FILTER 2.5\\"P.S. |
| 326 | PRESSURE GAUGE + STOP COCKP.S. |
| 327 | PRV P.S. |
| 328 | NRVP.S. |
| 329 | NETWORK - FINOLEX HDPE & PVC PIPESHDPE PIPE 75 MM PN4 (TANK TO PLOT)P.S. |
| 330 | PVC PIPE 75 MM 4KG/CM2P.S. |
| 331 | PVC PIPE 63 MM 4KG/CM2P.S. |
| 332 | EMITTING SYSTEMFINOGOL PLAIN LATERAL 16 MMP.S. |
| 333 | DRIPPER 8 LPHP.S. |
| 334 | START TO END SET FOR DRIP LINE 16 MMP.S. |
| 335 | BARBED COUPLER 16 MMP.S. |
| 336 | TEE 16 MMP.S. |
| 337 | ELBOW 16 MMP.S.. |
| 338 | ELBOW 16 MMP.S.. |
| 339 | BALL VALVE 63 MMP.S. |
| 340 | FLUSH VALVE 63 MMP.S. |
| 341 | VALVE BOX 12\\"P.S. |
| 342 | Pump: Crompton Greaves 10.00 Hp pump with necessary accessories.(Market Rate) P.S. |
| 343 | Providing and fixing H.D.P. container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery upto destinatin hoisting and fixing of accessories such as inlet,outlet over flow of all tanks capacity above 1000 to 20,000 litresD.S.R. 18.48 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 26, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 24 daysNov 21, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender