Tender For Repairing And Various Work Of Public Toilets, Urinal And Rain Basera Toilets From Ward No. 01 To 20 Bhinmal
Tender Value
4.95 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
7 days left
EMD
9900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalore → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairing And Various Work Of Public Toilets, Urinal And Rain Basera Toilets From Ward No. 01 To 20 Bhinmal
BOQ
| Sl. No. | Item Description |
| 1 | Brick work with machine moulded perforated bricks of classdesignation 125 conforming to IS: 2222 -1991 in superstructureabove plinth level upto two stories in cement mortar 1:6 (1 cement :6 coarse sand) : 24.4.2 |
| 2 | Repairs to plaster of thickness 12mm to 20mm in patches of area2.5 sq. metres and under including cutting the patch in propershape, raking out joints and preparing and plastering the surface ofthe walls complete including disposal of rubbish to the dumpingground within 50metres lead.With cement mortar 1:4 (1 cement : 4 fine sand) |
| 3 | Repair to damaged RCC slabs, beams and columns etc forstrengthening with cement mortar 1 : 2 in following steps i) Choppinglose and cracked concrete to required depth, cleaning the exposedsurface of steel and concrete with wire brush and sand papering ,cleaning of concrete surface with water as necessary and gettingdried. ii) Applying Epoxy primer on the exposed steel bars. iii)Applying Epoxy hardener and resin mix (as per manufacturer’sspecification) on concrete and steel bars with brush. iv) Spreading dry cement mortar 1 : 2 mix over epoxy treated wet surface andallow it to dry for one day. v) Plastering the surface with cementsand mortar 1 : 3 upto depth of 30mm complete. vi) Cure theplastered surface for 15 days All work including scaffolding etc.complete in all respect |
| 4 | Providing and fixing fine dressed sand stone/approved stoneTraditional work as per existing matching geometrical designincluding moulding work with fine finishing, fixing with thambli byproper adhesive and white cement with pigment including makinggroove etc. complete in all respect. |
| 5 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm drybrick honey comb shaft with bricks of class designation 75 and S.W.drain pipe 100 mm diameter, 1.8 m long complete as per standarddesign With bricks |
| 6 | 30mm thick factory made panel PVC door shutter consisting offrame made out of M.S. tubes of 19 gauge thickness and size of19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on either side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. panelling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification &drawing (for W.C. and bathroom door shutter). |
| 7 | Providing and fixing wood panelling or panelling and glazing inpanelled or panelled and glazed shutters for doors, windows andclerestory windows (Area of opening for panel inserts excludingportion inside grooves or rebates to be measured). Panelling forpanelled and glazed shutter 25 mm to 40 mm thick 5 mm thick.28.7.4.2 |
| 8 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. 32.15 |
| 9 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs toscratches etc. complete 33.46 |
| 10 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade Old work (one or more coats) |
| 11 | Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface) |
| 12 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 13 | P & F 1st quality Vitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufacture) with water absorption less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grouting the joints with white cement and matching pigment etc complete.Size 450 mm X 450 mm |
| 14 | Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 15 | Constructing masonry Chamber 30x30x50 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :With bricks |
| 16 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and the base support for tank |
| 17 | Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in-charge . for additional technical parameters of product/ work, refer Annexure \\"A\\" attacheded with this BSR 15 Watt |
| 18 | Supply & Fixing of phenolic laminated board of 6.4 mm thick forfresh air fan/exhaust fan up to size of 300 mm on existing windowframe including cost of board, cutting of hole , Nut bolts etc. asrequired.All as per pre approved by Engineer in-charge. Foradditional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 19 | Providing & Fixing of BEE Star rated copper wounded double ballbearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR .1200 mm Sweep BEE 1 Star rated (service value >=4.0 to < 4.5 ) |
| 20 | P & F ISI marked (IS :3854) 16 amp. flush type non modular switch CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 21 | P & F ISI marked (IS:3854) 6 amp. flush type non modular switchwith CM/L no. printed and made out from industrial gradePolycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technicalparameters of products/ work , refer Annexure \\"A\\" attached withthis BSR . |
| 22 | Providing & Fixing of of 3/5 pin 6 amp. flush type non modularsocket made out from industrial grade Polycarbonate or fireresistant ABS material, brass terminal with Porcelain based backcover & captive screws including cutting hole in tile and makingconnection testing etc. as required.All as per pre approved byEngineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR |
| 23 | Providing & Fixing of 3/6 pin 16 amp flush type non modular socket made out from Industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 24 | Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure 'A' attached with this BSR.Short point (up to 3 mtr.) |
| 25 | Medium point (up to 6 mtr.) |
| 26 | Long point (up to 10 mtr.) |
| 27 | Supplying and drawing FR PVC insulated & unsheathed flexiblecopper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR.2 x 1.5 sq.mm |
| 28 | 2 x 2.5 sq.mm |
| 29 | S&F following sizes (dia.) of ISI marked virgin material MMS (IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988) accessories as required in recess including cutting the wall, covering conduit and making good the same as required. Foradditional technical parameters of product / work refer Annexure 'A' attached with this BSR.25 mm |
| 30 | Providing & Fixing of 6 amp. Combined flush type non modularsocket and switch set as per PWD specification for electricalWorks,made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . |
| 31 | Providing & Fixing of 16 amp. Combined flush type non modularsocket and switch set with indicator and fuse set as per PWDspecification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached withthis BSR . |
| 32 | Providing & Fixing of of Double ball bearing, copper woundedcapacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \\"A\\" attached with this BSR . 225 mm sweep |
| 33 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P.brass pillar taps,32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever require : White Vitreous China Wash basin size 630x450 mm with a pair of 15mm C.P. brass pillar taps |
| 34 | Providing and fixing C.P. brass bib cock of approved qualityconforming to IS:8931 15 mm nominal bore. |
| 35 | Providing and fixing C.P. brass long nose bib cock of approvedquality conforming to IS standards and weighing not less than 810gms.15 mm nominal bore. |
| 36 | Providing and fixing C.P. brass angle valve for basin mixer andgeyser points of approved quality conforming to IS:8931..15 mm nominal bore. |
| 37 | Providing and fixing PTMT angle stop cock 15 mm nominal bore.Weighing not less than 85 gms. |
| 38 | Providing and fixing PTMT soap Dish Holder having length of138mm, breadth 102mm, height of 75mm with concealed fittingarrangements. Weighing not less than 106 gms |
| 39 | Providing and fixing Unplasticised P.V.C. connection pipe withPTMT Nuts collar and bush of approved quality and colour. 15 mm nominal bore with 30cm length |
| 40 | U-PVC Single socketed rain water pipe confirming to IS : 13592Class \\"A\\" 110 mm dia |
| 41 | P.T.M.T. Ball Cock 15mm Complete with Epoxy Coated AluminiumRod & H.D. Ball |
| 42 | Chlorinated Polyvinyl - chloride (CPVC) pipe 15 mm outer dia. |
| 43 | Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm outer dia. |
| 44 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required .W.C. pan with ISI marked white solid plastic seat and lid |
| 45 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 46 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.450MM long towel rail with total length of 495mm, 78mm wide andeffective height of 88mm, weighing not less than 170gm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 24, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender