Tender For Repair/ Maintenance Of Floor, Plinth, Roof, Joinery And Other Connected B/R Works In Wsa At Af Stn Suratgarh
Tender Value
35 Lakhs
Estimated cost
Bid Submission
23 Nov 2026
11 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganganagar → Rajasthan
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/ Maintenance Of Floor, Plinth, Roof, Joinery And Other Connected B/R Works In Wsa At Af Stn Suratgarh
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 06-Nov-2026 | Corrigendum_01 | Date | 23-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | BOQ (REPAIR/ MAINT OF FLOOR, PLINTH, ROOF, JOINERY AND OTHER CONNECTED B/R WORKS IN WSA AT AF STN SURATGARH) |
| 2 | Demolition of brick masonry built in cement mortar including all quoins, arches and removing from site etc. complete all as specified and directed. |
| 3 | M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cm 1 : 6 complete all as specified and as directed by Engr-in-Charge. |
| 4 | All as per Ser item No 2 here in before but using old bricks |
| 5 | Demolition of cement concrete (un-reinforced ) of any description in ground floors and paving not exceeding 15 cm thick (below or above the ground level) and removing rubbish from the premises. complete all as specified and directed. |
| 6 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site complete all as specified and direcetd. |
| 7 | Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each and removing from site complete all as specified and direcetd. |
| 8 | Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each and removing from site complete all as specified |
| 9 | M&L Factory made Pressed steel frames of size 105mmx60mm made of 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, complete all as specified. |
| 10 | M&L for PCC 1:3:6 type C0 (using 12.5mm graded stone aggregate) as in hold fast iron fixing and back filing of pressed steel door frame including necessary form work all as specified. |
| 11 | S&F 35 mm thick 2nd class Hard wood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated completely all specified and directed. |
| 12 | S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified. |
| 13 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification. |
| 14 | S&F butt hinges, medium weight, cold rolled, mild steel 100 mm long (ISI marked), complete all as specified. |
| 15 | S&F Aluminum handles, 150 mm size cast type complete all as specified and directed. |
| 16 | S&F aluminum tower bolt 150 mm size cast type complete all as specified and directed. |
| 17 | S&F aluminium anodised, barrel tower bolt of extruded section and fixed, 200mm long (ISI marked), complete all as specified. |
| 18 | S&F aluminium alloy, 16mm dia and 250mm long anodised, sliding door bolt with hasp, staple (bolt type) with and fixing clips of sheet, cast or excluded sections and fixing bolts and sliding bolts of excluded sections or cast aluminum alloy and fixed, complete all as specified. |
| 19 | S&F as in replacement Stainless Steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks, wire staples or beading etc, complete all as specified and directed. |
| 20 | S&F fancy type stainless steel 20 mm dia curtain rod thickness of pipe not less than 1.0 mm including stainless steel brackets and stainless steel end knobs fixed with plugs & screws, complete all as specified and directed. |
| 21 | S&F of 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type back side and one face is covered with decorative face veneer with lipping/frame to match, fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 22 | S&F in replacement brass 4 Lever mortice lock, vertical type,size 100mm complete all as specified . |
| 23 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fastenersof required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snapbeading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-chargeNote :- Glass/wire glass shall be measured and paid separately. |
| 24 | M & L for anodised Aluminium frame works such as grills with frames and frame guard bars and similar works. Complete all as specified and directed. |
| 25 | S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, holdfast and concrete bed block complete with outer side glazing bars shutter and inner side wire mesh shutter including glass panes, dovetailed or welded complete all as specified and directed. |
| 26 | S&F powder coated any colour Anodised aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 27 | M&L sheet glass 5.5mm thick, ordinary quality and glazing with, rubber packing exc 0.5 sq m in each pane complete all as specified and as directed by the Engineer-in-Charge |
| 28 | S & F as in replacement Aluminium die cast body door closer hydraulically regulated designation No. 3, universal type suitable for door shutter 851 to 1000 mm in width and 61 to 80 Kg in weight complete all as specified and directed. |
| 29 | Supply & fixing Aluminium powder coated glazed three track sliding window of frame 92 x 38x 1.5 mm thick and sliding shutter of section 40 x 18 mm x 1.5 mm including 4 mm thick sheet glass ordinary quality in two track shutters and in one track stainless steel wire cloth, .56 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel staples including all fitting such as aluminium handle of size 100 mm and locking arrangements with each moving leaf aluminium jali, MS Grill with 30 mm x 5 mm flat iron Square bar @ 10 cm c/c complete all as specified and directed by the engineer in charge. |
| 30 | M&L Granite of thickness not less than 18 mm of any type work(table rubbed and polished) in steps, jambs,pillars windows cill cooking platform and like including pointing in white/colour cement and pigment to match with shade of granite including bull nosing of external,including demolition of stone slab and tiles of any description or thickness complete all as specified and as directed. complete all as specified and directed. |
| 31 | M&L for 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub base,flooring, pavings etc complete all as specified and as directed. |
| 32 | M&L for PCC 1:2:4, type B-0 using 12.5mm graded crushed stone aggregate as in coping, benching, complete all as specified & directed. |
| 33 | M & L TMT bars 8 mm dia and cut to length, bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed. |
| 34 | M&L for Plain cement concrete 1:2:4 type B-O (12.5mm graded stone aggregate) 40 mm average thickness as roof finished, complete all as specified and directed by Engineer-in-Charge |
| 35 | M&L 1st quality Vitrified ceramic tiles of thickness not less than 9 mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 15 mm thick screed bedding in CM (1:6), complete all as specified and directed. |
| 36 | M&L 1st quality Vitrified ceramic tiles 10mm thick (square/ rectangular) polished area of each tiles not exceeding 0.36 Sqm for vertical surfaces skirting/Dado etc., set and jointed in neat cement slurry and pointed in white or colour cement to match with and including provision of 10 mm thick screed bedding in CM (1:4), complete all as specified and directed. |
| 37 | M&L for providing and laying 60mm thick factorymade chamfered edge cement concrete paver block of M-35 grade conforming to IS: 15658:2006 with lates amendments with approved colour design & pattern as in footparth, hape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of fine sand, compacting and proper blocks into the sand bedding layer hrough vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all a specified and directed |
| 38 | M&L 75mm cement concrete (1:2:4) Type B2 , 40 mm stone graded agg as in path/hardstanding, finished even and smooth w/o using extra cement. complete all as specified and directed. |
| 39 | M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 , using 40 mm graded crushed stone aggregate as in floor, laid in slope of 1:12 and surface finished even and smooth without using extra cement including making joint at 2.5 m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand). Complete all as specified and directed. |
| 40 | Demolition of stone slabs/ tiles of any description or thickness in floors, aprons etc, laid, bedded and pointed in any mortar and removing rubbish from the premises. Complete all as specified and directed. |
| 41 | M&L for First quality glazed ceramic coloured tiles of (450x350mm) x 7 mm thick, laid on vertical surfaces of wall such as skirting, dados and risers to steps etc laid over and including 10mm thick cement plaster in CM (1:4) set and jointed in neat cement paste of honey like consistancy and pointed in white or coloured cement to match the shade of tiles with & including dismantling of existing tiles of any description ,complete all as specified and directed by the Engineer in Charge. |
| 42 | M&L for First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sq.m but not exceeding 0.18 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed of cement mortar (1:6) including pointing in white cement with pigment to match the shade of tiles,with & including dismantling of existing tiles of any descriptioncomplete all as specified and directed by the Engineer in charge. |
| 43 | M&L for machine cut polished kota stone slab flooring of size of Kotastone not less than 550 mm x 550 mm and 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 20mm thick screed bed in cement mortar 1:6, rubbing, grinding and polishing to achieve mirror finish, complete all as specified and directed. Note : Kota stone shall be laid in one piece for treads and risers for step, window cills and moulding/rounding of edge properly. |
| 44 | M&L for polished kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab, laid over and including 10mm thick rendering in cement mortar 1:4, rubbing, grinding, rounding of edges and polishing to achieve mirror finish, complete all as specified and directed.Note : Kota stone shall be laid in one piesce for treads and risers for step, window cills and moulding/rounding of edge properly. |
| 45 | Taking down cement plaster on brick or concrete wall surfaces etc including raking out joints, hacking for key, scrubbing down with water and removing rubbish from the premises etc. complete all as specified and directed. |
| 46 | M&L for 12 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement as on wall complete all as specified and directed. |
| 47 | Material and labour for 15 mm thick rendering in cement mortar 1:4 mixed with approved water proofing compound on fair faces of brick surfaces or concrete surfaces, surface finished even and smooth without using extra cement all as specified and directed.Note: Water proofing compound shall be measured and paid separately. |
| 48 | M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces of roof projection/ ceiling and surface finished even and smooth without using extra cement, complete all as specified and directed. |
| 49 | M&L for rough cast plaster with a mixture consisting of crushed stone or fine gravel aggregate of size 6mm to 8mm as directed, mixed with coarse sand, fine sand and cement in the ratio of 1:1:1, finished even rendereing with under coat 15mm thick cement and sand mortar 1:3 complete all as specified and directed |
| 50 | M&L for preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. |
| 51 | Applying two coats of exterior acrylic emulsion (weather proof treatment ), in plain patterns, over new rough cast plastered surfaces , including preparation and using primer,complete all as specified and directed. |
| 52 | M&L for prepration of new or previously untreated wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed. |
| 53 | M&L for preparation of new plastered or unplastered surfaces of wall and applying two coats of oil emulsion distemper over 1.5 mm thick JK/Birla wall care putty to achieve smooth finish surface, complete all as specified and directed. |
| 54 | M&L for preparation of old plastered wall surfaces and applying one coat of white wash complete all as specified and directed. |
| 55 | M&L for preparing old surfaces of walls by complete removal of existing treatment by sanding and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance interior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm with rollers.complete all as specified and as directed. |
| 56 | M&L for Preparation of old painted wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint, complete all as specified and directed by Engineer-in-Charge. |
| 57 | M&L for Preparation of old painted steel surfaces of any description not otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engineer-in-Charge. |
| 58 | M&L for prepration of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 59 | M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash all as specified & directed by Engineer-in- Charge. |
| 60 | M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Exterior Emulsion Paint (in Camouflage pattern) with approved Tint over a coat of Primer (as per Manufacturer's instructions) and 1 mm thick putty, complete all as specified and as directed by Engineer-in-Charge. NOTE: Rates quoted by the tenderer shall be deemed to be included with following application as under :-(a) The surfaces shall be cleaned to remove loose dirt or dust,lichen, algae, fungi or any organic growth by use of stiff brush, washed well and allow water to dry.(b) All cracks, voids and minor damages shall be patched/repaired prior to application of paint with white cement putty or with Plaster of Paris. |
| 61 | M&L for Complete Removal of existing Surfaces Treatment and applying Two Coats of Exterior Emulsion Paint (in Plain/New Camouflage pattern) with approved Tint over a coat of Primer (as per Manufacturer's instructions) 1 mm thick putty, complete all as specified and as directed by Engineer-in-Charge.NOTE: Rates quoted by the tenderer are included with following apllication as under :- (a) The surfaces shall be cleaned to remove loose dirt or dust, lichen, algae, fungi or any organic growth by use of stiff brush, washed well and allow water to dry. (b) All cracks, voids and minor damages shall be patched/repaired prior to application of paint with white cement putty or with Plaster of Paris. |
| 62 | M&L for applying two coats of distemper oil emulsion on old plastered surfaces over a coat of Chalk whitening on wall including preparation of surfaces complete all as specified |
| 63 | S&F in replacement vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap 100 mm bre and necessry lime concrete inl making good to floor. Complete all as specified and directed. |
| 64 | S&F in replacement viterous china wash down water closet pan, white (pedestal pattern), including plastic water closet seat, black/white, closed pattern with recessed bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern) and inlcuding flush pipe set of CP jet with PVC pipe of superior quality complete all as specified and directed. |
| 65 | S&F in replacement, PVC valveless, dual type, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float , 32 mm dia PVC long bend flush pipe 90cm long, complete all as specified and directed. |
| 66 | Supply and fixing in replacement, wash hand basin vitreous china flat back 600 x 450 mm size white, first quality, with and including PVC waste coupling 32mm size, PVC waste pipe 32mm bore, brackets of Mild Steel angle iron (35mmx35mmx5mm) of suitable size including two coat of synthetic enamel paint over a coat of primer over angle iron brackets to walls complete all as specified and as directed. |
| 67 | S&F as in replacement 15mm bore Pillar taps cast copper alloy, with capstan head, fancy type, chromium plated, weight not less than 665 gm screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe |
| 68 | SS&F in replacement stop/angle valves concealed type, 15mm bore, fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, both ends screwed for iron pipe or for union etc., complete all as specified and directed. |
| 69 | S&F in replacement Gun-metal, globe or gate valves of 20mm dia, with iron wheel head, screwed both ends for iron pipe, complete all as specified. |
| 70 | S&F in replacement PVC connection 15mm dia, 450 mm long, hot water grade with brass chromium plated nuts and washers at both ends, complete all as specified. |
| 71 | S&F in replacement bib tap, 15mm bore, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed. |
| 72 | S&F in replacement, 15mm bore, WHB/Sink mixer, fancy type, chromium plated weight not less than 1 kg, cast copper alloy, with capstan heads, screwed down, high pressure, with or without lettered `Hot’ or `Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified. |
| 73 | S&F in replacement towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed. |
| 74 | S&F in replacement 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 75 | S&F in replacement Towel Rack 600mm long, Chromium Plated, without Lower Hangers but with 3 No. Hooks, complete all as specified and as directed. |
| 76 | S&F Health faucet mild steel chromimum plated auitale for 15mm dia pipe with 1.25m long long flexible tube ABS wall hook including making connections and fixed and complete all as specified. |
| 77 | S&F as in replacement Rotational moulded plythelene white water storage tank tripple layered white coloured, 1000 litres capacity (cylinderical vertical with cxlosed top) hoisted with thread tank cover and fixed in position including GI tank nipple & with union(two nos each), including 20mm for ball valve brass high pressure, with polythene float and fly nut complete all as specified and directed. |
| 78 | All as per srl item No 76 here in before but tank of capacity 500 litre |
| 79 | M&L for Galvanised iron tubing 15mm bore,medium grade,with all fittings fixed to walls or ceiling or laid in floors, in concealed pipe work including making good the chases etc in cement mortar(1:3) after fixing of pipe,incuding taking down of old rusted/u/s GI pipe removal from site. complete all as specified and directed.(Rates for cutting of chases is included in respective items of taking down).complete all as specified and directed |
| 80 | M&L for Galvanised iron tubing 20mm bore,medium grade,with all fittings fixed to walls or ceiling or laid in floors, in concealed pipe work including making good the chases etc in cement mortar(1:3) after fixing of pipe,incuding taking down of old rusted/u/s GI pipe removal from site, complete all as specified and directed.(Rates for cutting of chases is included in respective items of taking down).complete all as specified and directed |
| 81 | Cleaning and removing all scales and dirt etc from tanks of cap 500 Ltr and from mouths of circulating pipe etc for any capacity ltrs capacity of tanks and removing rubbish from the premises as directed by eningeer -in-charge. (Note: Date of cleaning to be written on the tank after cleaning) |
| 82 | All as per srl item No 80 here in before but capacity 1000 Ltr |
| 83 | Dismantling for Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified. |
| 84 | S&F Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructionscomplete all as specified and directed. |
| 85 | M & L rolled mild steel as in framing for cladding and the like fixed with angle cleats and connecting plates Fe410-W (Gde-E-250) quality-A all as specified and directed by Engr-in- charge |
| 86 | Dismantling structural steel or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 87 | M&L 10 mm thick screed plaster on roof in CM 1:4 using WPC (WPC shall be measured and paid separately) |
| 88 | M&L APP based polymeric membrane 3 mm thick having weight 3 Kg/Sqm reinforced with polyster non-mover fabric (not less than 150 gm/sqm) laid over a tack coat of bitumen 85/25 @ 1.2 kg/m2 on surface by forced applicantion . Complete all as specified and directed. |
| 89 | Dismantling brick tiles or terracing tiles, single layer on roofs and removing from site. |
| 90 | Demolition of mud in roofs, any thickness including plastering and leeping and removing from site. |
| 91 | 40 mm thick brick tiles laid on roof and joints grouted jointes in cement mortar 1:3 mixed with 5% crude oil by weight of cement complete all as specified and directed. |
| 92 | All as per srl item No 90 here in before but using old brick tiles. |
| 93 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness with grid of any type and pattern including cover fillets and removing from site complete all as specified and directed by engr-in Charge. |
| 94 | S&F min 6 mm thick designer sheet false ceiling with GI frame work incl all necessary drilling, cutting to fix electrical items complete all as specified and directed with floowing:(a) GI sheet channel 30x25x20mm of 24 Gauge fixed with rawl plug and screws 450 mm centre to centre along with perimeter of wall.(b) GI sheet channelmade to shape 50x40x40mm of 24 Gauge placed @ 600 mm centre to centre from perimeter of wall except long wall (in one span)(c) GI sheet intermediate runners of size 45x10x10mm of 24 Gauge fixed @ 1200 mm centre to centre leaving frame of one side wall (in other span)(d) GI sheet 25mm wide & 20 mm gauge suspenders fixed with steel fasteners to roof, ceiling @ 1200 mm centre to centre incl plugging in RCC slab. |
| 95 | S&F decorative PVC Wall lining fluted louvers consisting of 8mm thick Plain/ colour PVC sheet inclusive of solvent cement and fixing at site complete all as specified & directed by Engr -in charge. |
| 96 | Supply only Integral waterproofing compound.complete all as specified and directed |
| 97 | M & L as in replacement 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each panes as specified |
| 98 | M&l for chequered cement concrete tile 30cm*30*cm*25mm thick set ,jointed and pointed in cement slurry and pigments laid over and including screed bed 20 mm thick in CM 1:6 as in floors complete all as specified and directed by engr-in-charge |
| 99 | S&F in replacement PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls, Type 'B', ISI marked of 110mm bore. complete all as specified and directed |
| 100 | S&F in replacement PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls or laid in floor, Type 'B', ISI marked of 75mm bore. complete all as specified and directed |
| 101 | S& F as in replacement PVC (SWR) bend with access door of any radius of 110mm bore. complete all as specified and directed |
| 102 | S& F in replacement PVC (SWR) bend with access door of any radius of 75mm bore. complete all as specified and directed |
| 103 | S&F in replaceement plastic water closet seat cover white /colour ,closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified |
| 104 | S&F in replacement Bib Tap 15mm bore , 2-in-1, Cast Copper alloy, Chromium Plated, suitable for fixing of Jet including Flange screwed down ,complete all as specified and as directed. |
| 105 | S&F in replacement 15mm bore dia,cast copper alloy, fancy type,chromium plated, two way angle valve cock (concealed type) ,complete all as specified and as direcetd. |
| 106 | S&F in replacement vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union (fixing to trap and waste pipe) fixed, including urinal spreader , complete all as specified and as directed. |
| 107 | S&F in replacement vitreous China Urinal, Half stall type (White) , including providingand fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush/waste pipe, grating and Union for discharge pipe. (inclusive of fixing supply pipe to trap, waste pipe and urinal spreader) , complete all as specified and as directed. |
| 108 | S&F in replacement for vitreous china urinal partition white of size 310x700 mm.complete all as specified and as directed. |
| 109 | M&L Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors all as specified by Engineer-in-charge. |
| 110 | Earth filling over embankments of traverses around holes etc including clearing of small bushes complete all as specified and directed by the Engineer in Charge.Note: (i) Earth , shall be brought by contractor from out side MOD land of any lead at his own arrangement. (ii) The Earth brought at site shall be stack in proper trapezoidal shape andmeasurement before placing it in traverse / embankment and explosive store.(iii) All cost of procurement of earth/tibba including cost of transportation, compaction, royalties, tax etc shall be deemed to be included in the unit rate quoted by the contractor. |
| 111 | M&L for polymer-modified, free-flow, non-shrink micro-concrete of approved make and specification for structural repair/strengthening of RCC members(coloumn, chajja,beamand front faciaand retaining wall, including removal of loose, damaged and honeycombed concrete, cleaning and preparation of the exposed surface and reinforcement, application of approved anti-corrosion protective coating to exposed reinforcement in two coats and application of approved bonding agent over the prepared concrete substrate, followed by placing/pumping of ready-to-use micro-concrete of required grade and thickness, including formwork/shuttering wherever required, proper compaction, finishing, curing, removal of shuttering, protection of treated surface and all necessary tools, plants, labour, scaffolding, leads, lifts and incidental works, complete all as specified and as directed by the Engineer-in-Charge note:-(a)Site for application is at various locations in patches and height varies up to 12M.(b) reinforcemnent shall be measured and paid separately |
| 112 | Removal of soil/muddy soil/grass/vegetation by manual/mechanical means in drains(not exceeding 1.5m deep) ,culverts including dressing of sides and bottoms without damaging the drain wall and PCC , including getting out the excavated soil and disposal of the same excavated soil as directed, within a lead of 250m from drain complete all as specified and directed by Engr-in-Charge |
| 113 | Removal of soil/muddy soil/grass/vegetation(of any heihgt and width) by manual/mechanical means from Plinth including cleaning of bottoms without damaging the PCC and toe wall, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 250m from drain complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
| 114 | Removal of soil/muddy soil/grass/vegetation(of any heihgt and width) by manual/mechanical means from Plinth including cleaning of bottoms without damaging the PCC and toe wall, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 250m from drain complete all as specified and directed by Engr-in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 06, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 23, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 11 daysNov 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysNov 25, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender