Tender For Improvement To Pft Infrastructure Of 10 Ascand Misc Works At Af Stn Bihta.
Tender Value
18.87 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
18 days left
EMD
37740
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Patna → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement To Pft Infrastructure Of 10 Ascand Misc Works At Af Stn Bihta.
BOQ
| Sl. No. | Item Description |
| 1 | B/R WORKS |
| 2 | PCC type B-1 (1:2:4), using (20 mm graded stone aggregates) as in surface channel and drain etc complete all as specified. |
| 3 | Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, complete all as specified and directed by Engineer-in-charge. |
| 4 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in as in lintels over 1.5 metre clear span, cills, steps, seismic and other similar band, plinth courses, lacing courses , copings, kneelers, apex stones, bed plates, water troughs and the like complete all as specified. |
| 5 | Brick with fly ash brick, straight or curved on plan exc 6m mean radius built in cement mortar (1:6), complete all as specified. |
| 6 | Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet and edges will be painted to match with printed sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified. |
| 7 | Factory made solid PVC moulded door shutter, 28-30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2 mm thick plain colur PVC sheet on back face, as shown on page 181 of MES Schedule Part-II, complete all as specified. |
| 8 | Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300 mm long, complete all as specified. |
| 9 | Aluminium anodised barrel tower bolt of extruded section 150mm long, ISI marked, complete all as specified. |
| 10 | Stainless steel 100 mm long butt hinges with stainless steel screws, ISI marked complete all as specified. |
| 11 | Steel windows for industrial buildings, fixed type, with glazing bars, complete all as specified and directed by Engineer-in-Charge. |
| 12 | Anodised aluminium snap grid frame work of size 605mm x 605mm for false ceiling complete with acessories all as specified and shown on serial page No.186 section 8 of SSR Schedule Part-II 2020. |
| 13 | Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 14 | 8mm thick Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid, complete all as specified and directed by Engineer-in-Charge. (Frame work for ceiling shall be measured and paid separately) |
| 15 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 16 | Framed mild steel work such as grills, grating, ladder etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified. |
| 17 | Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 18 | Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 19 | 50 mm thick PCC type B-1 (1:2:4), using 20 mm graded stone aggregates as in damp proof couarse, complete all as specified. |
| 20 | Glazed ceramic coloured tiles 7-8 mm thick, area of each tile exc. 0.13 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified |
| 21 | Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 0.18 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 22 | Machine cut Kota stone slab 18-22mm thick on vertical surfaces as in staircase riser skirting/ dado etc over and including 10 mm thick rendering in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified |
| 23 | Only Polishing of existing kota stone Floor 20-25mm thick with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete all as specified and directed by Engineer-in-Charge. |
| 24 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6), complete all as specified. |
| 25 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified.NOTE:-WPC will be measured and paid for separately under respective item of BoQ. |
| 26 | Supply only integral water proofing compound, ISI marked, complete all as specified |
| 27 | Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two layer & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer. |
| 28 | Prepration of new plasterd wall surfaces of any description & applying Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer complete all specified |
| 29 | Plain sheet glass 4 mm thick ordinary quality and glazing with rubber gasket in squares n. exc. 0.5sqm in each pane complete all as specified. |
| 30 | Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron (new) surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified. |
| 31 | Steel tubes ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified of size: - |
| 32 | 15 mm bore |
| 33 | 20 mm bore |
| 34 | 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, complete all as specified including the following acessories: -(i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, complete all as specified.(iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, complete all as specified.(iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, complete all as specified. |
| 35 | Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete. |
| 36 | Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, complete. |
| 37 | 15 mm pillar taps, chromium plated, screwed down high pressure, with or without lettered `Hot' or Cold with long screwed shanks and fly-nuts, screwed for iron pipe, complete. |
| 38 | Hand health fuccets with 1200mm long connecting pipe and holder, complete all as specified and directed by Engineer-in-charge. |
| 39 | Vitreous China wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with 1.50 metre long flexible stainless steel braided tube, soft close ISI marked PVC seat & cover, complete all as specified |
| 40 | Vitreous China wash basin, white, oval type, size 565 x 355 x 265 mm, ISI marked, including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe, complete all as specified. complete all as specified. |
| 41 | PVC low level flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, complete. |
| 42 | Looking mirror 600 x 450 mm, selected quality glass 5.5 mm thick, mounted on PVC ply not less than 6 mm thick, and provision of PVC frame alround fixed with chromium plated brass screws and rawl plugs, complete. . |
| 43 | Toilet paper holder, vitreous China, box type,complete all as specified and directed by Engineer-in-charge. |
| 44 | Stainless steel soap dish, fixed to wall with SS screws and PVC rawl plugs, complete. |
| 45 | PVC connections 15 mm size of length 600 mm with PTMT nuts, complete all as specified. |
| 46 | 75 mm external dia pipe uPVC pipes, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors / fixed to wall as SWR pipes, complete all as specified |
| 47 | 75 mm external dia pipe uPVC/PVC bend any radius with access door complete all as specified. suitable for uPVC soil waste discharge pipes complete all as specified |
| 48 | Cast iron 100 mm floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified. |
| 49 | Reinforced concrete pipes 150 mm bore, class NP-2, laid and jointed complete with collars, laid in trenches and jointed, ISI marked, complete all as specified. |
| 50 | Concrete bed to drain pipes 150 mm bore including packing under, and haunching against the sides of pipes after they are laid and tested; in Cement concrete 1:3:6 type C-2, complete all as specified. |
| 51 | Cutting into existing manholes for connecting new drains 150mm dia, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, & reforming benching as required, complete all as specified. |
| 52 | E/M WORKS Please Enable Macros to View BoQ information |
| 53 | E/M WORKS Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender