Tender For Providing And Installation Of High Mast Flag At Mcd Park In Palam Vidhan Sabha Ac-37 Under Swr-Ii , New Delhi During 2026-27. (Sh:- Civil & Electrical Works).
Tender Value
28.61 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
10 days left
EMD
57231
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing And Installation Of High Mast Flag At Mcd Park In Palam Vidhan Sabha Ac-37 Under Swr-Ii , New Delhi During 2026-27. (Sh:- Civil & Electrical Works).
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.1.1) All kinds of soil |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 3 | Extra for every additional lif of 1.5 m or part thereof in excavation / banking excavated or stacked materials.3.1) All kinds of soil |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 5 | Foundations, footings, bases for columns |
| 6 | Columns, piers, abutments, pillars, posts and struts |
| 7 | Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/ Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.5.1) Concrete of M10 grade with minimum cement content of 220 kg /cum |
| 8 | Extra for shuttering in circular work (20% of respective centering and shuttering items) |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.7.1) Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 10 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.8.1) All works upto plinth level |
| 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:9.1) Cement mortar 1:4(1 cement :4 coarse sand) |
| 12 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :10.1) Gang saw cut stone |
| 13 | 30 mm thick White sand stone |
| 14 | 30 mm thick Red sand stone |
| 15 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 16 | 40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement: 5 coarse sand) with joints finished flush. |
| 17 | Red sand stone |
| 18 | White sand stone |
| 19 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 20 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.14.1) Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) |
| 21 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 22 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.16.1) 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. |
| 23 | Deduct on account of GST as per correction factor @0.973 on DSR 2023 Items as per SE(TAS)CPWD O.M. No. 158/SE (TAS)/GST/2024/02-E dated 08/08/2024 (DSR Items Rs.1056220- x 0.973= 1027702/-) i.e..= (Rs.1056220-Rs.1027702=(-) Rs -28518) |
| 24 | Add 4.03% Cost Index on DSR Items (As per OM no DG/Cost Index/13 Dated 07-01-2026) |
| 25 | Supply of tall polygon Flag Mast at individual site. Flag mast shaft shall be in equal sections, hot dip galvanised and section designed suitably for wind velocity as per IS 875 and approved by engineer in charge. (Indicative minimum parameters shall be as per technical data sheet). The shaft shall be PU painted with a coating of etch primer, primer and PU paint.17.1) 35 meter height in 4 equal sections. |
| 26 | Supply of high tensile foundation bolts having minimum yield strength of 600N/sq. mm manufactured from special steel for flag mast along with nuts, washers, anchor plates and templates at individual site and as per direction of Engineer-in-Charge. (Indicative minimum parameters shall be as per technical data sheet.)18.1) For 35 meter tall polygon flag mast 16 nos M 30x 1000mm Long |
| 27 | Supply of Indian National Flag of size proportion (3:2) made out of 100% knitted polyester fabric with reinforced super-strong nylon webbing on all 3sides & rope/toggle sleeve & eyelets at induvial site and as per direction of Engineer-in-Charge.19.1) Flag size 10972.8mm x 7315.2mm ( 36 ft x 24 ft) for 35 meter flag mast. |
| 28 | Installation (Erection), testing, commission of the Flag Mast with the help of suitable equipment’s including assembly of shafts & operating system all complete i/c. electric connections aviation light, testing & commissioning etc. as required as per direction of Engineer-in- charge. including hoisting of flag of all size and as per direction and approval of Engineer-in-charge (Height shall be measured from top of resting platform).20.1) 35-meter-tall flag mast. |
| 29 | Supply of system at induvial site for raising lowering of Flag with followings i) double drum winch and motor suitable for 6 mm dia galvanised wire rope for flag hoisting and integral power tool for the raising and lowering of Flag. ii) 6 mm dia alvanised wire rope for flag hoisting complete with all clamping arrangement for flag. iii) 3 nos additional 6 mm dia safety wire ropes. iv) Lightning finial with ornamental fibre dome. v) Aviation’s brackets 2 nos vi) LED aviation wiring with 3C x 2.5 sq mm Copper armoured cable of suitable length and as per direction of Engineer-in- Charge. (Minimum parameters shall be as per specifications)21.1) For 35 meter high flag mast. |
| 30 | Extra labour for laying circular brick masonary on curved on plan for a mean radious not exceeding 6 m |
| 31 | Fixing of high tensile foundation bolts having minimum yield strength of 600N/sq. mm manufactured from special steel for flag mast along with nuts, washers,anchor plates and templates at individual site and as per direction of Engineer-in-Charge. 35 mtr Flag Mast |
| 32 | Drilling of bore hole of 100 to 150 mm dia including providing labour and material required for carrying out soil testing for bearing capacity of soil complete as per direction of Engineer-in-Charge performing standard penetration test as per IS-2131-1981, taking disturbed and undisturbed samples at every 1.5 mtr interval or at change of starta as per relevent IS specifications complete including drilling in all types of soil, other than boulders and rock showing soil profile, depth of water table filled up soil, rocky strata etc net safe / allowable bearing capacity at a required depth directed by Engineer-in-Charge. Preparation and submission of detailed conducting soil test vsoil investigation |
| 33 | Mobilization and Transportation of (providing and bringing at site) equipement, machinery , T&P etc required for carrying out standard penetration test, soil investigation etc for bearing capacity testing. |
| 34 | Wet cleaning of National Flag Whenever & wherever required with using Chemical Compound etc., as required for Size 36 Feet x 24 Feet including cost of taking down and hoisting of flag, cost of +conveyance/ transportation /labour etc. all complete and as per direction of Engineer-in-charge |
| 35 | Making arrangment for taking half Down or Half Hosting the National Flag with full dignity and rehosting the National flag during national mourning all complete i/c man power & necessary transportation etc as per direction of Engineer-in-Charge. |
| 36 | Disposal of silt/sludge/rubbish/earth/mixed malba by mechanical transport fitted with GPS Mechanism including loading and unloading with lead and lifts upto nearest authorized MCD dumping ground sanitary land fill site or available PWD sie complete as per direction of emgineer-in-charge.(Payment will be made on production of print out of GPS mechanism & MCD receipt for payment of ground tax). MCD dumping ground/sanitary land fill tax if any shall be reimbursed separately on production of receipt. |
| 37 | ELECTRICAL WORK |
| 38 | Supplying & erection of flange mounted hot dip galvanized (min 70 Micron) octagonal poles of 5 mtrs. height made from 3 mm thick HT steel plate having bottom dia of 130 mm & top dia of 70 mm complete with window full sleeve type cover arrangement at a height of 0.5 / 2 mtrs from the base for cable termination block etc. and galvanized base plate of size 200 mm x 200 mm x 12 mm thick on the existing cement concrete pedestal as required i/c supplying and fixing of the following in the window box provided for cable termination :-a) Supplying and fixing 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. G.I strips 4mm thick of suitable length and having suitable size tapped holes - 10nos. as reqd.b) Supplying and fixing of 63 Amp terminal block suitable for 25sq.mm conductor -4 nos. & shorting links – 5nos. on DIN channel i/c providing and fixing DIN channel of suitable length – 2 nos. on the existing laminated sheet.c) Supplying and fixing 6 Amp, SPMCB, ‘C’ Characteristics Curve - 2 No. Earth stud-2Nos. welded at suitable height two nos. washers, springs washers & nuts.d) Cable support clamp suitable for 2 Nos of 4x25sqmm cable. |
| 39 | Providing and laying in position (1:2:4) reinforced cement Concrete foundation of size 500 mm (L) X 500mm wide and 1200mm deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement ring of cold twisted bars of 12 mm dia 1350mm long (approx) 6 and reinforcement ring of cold twisted bar of 8mm dia -2200 mm (approx) 8 nos. (with 150 mm spacing) as requried with positioning of foundation bolts and provoding 63 mm dia (O.D.) DWC, HDPE pipe of 0.3 mtrs. length for cable entry & exit as reqd. |
| 40 | Supplying and fixing 4 Nos. 16 mm dia X 600 mm long GI foundation bolt (EN8 grade) with nuts, washer including 2 Nos. template of 3mm thick size 240mm x 240mm with 4 nos. 28mm dia holes, to match with PCD of Pole base plate as reqd. |
| 41 | Fabrication, designing, supplying & Fixing of 1.0 mtr length & suitable dia for fixing on 70 mm dia pole galvanized flood light pole bracket with tightening bolt etc. as per existing design of brackets of roads where the street light pole bracket to be fixed i/c fixing top on 5.0 mtr height existing pole as reqd. |
| 42 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (40 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.33.1 ) 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 43 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 44 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 45 | Providing and fixing/laying 6 SWG dia G.I. wire on surface/recess/ in pipe for loop earthing along with existing cable as required. |
| 46 | Supplying and Laying of following size XLPE insulated PVC outer sheathed armoured Copper cable suitable for rated voltage of 1100 Volts ISI marked conforming to IS: 7098-1988 with upto date amendments i/c laying direct in existing DWC/GI/Hume pipe, connection complete etc. as reqd.37.1) 3 core 2.5 sq.mm |
| 47 | SITC of 350W SMD LED Flood light fixture with System efficacy of 110 lm/W (38675 lumens). Luminaire shall be made up of LM6/ADC12 Alloy, non-corrosive, pure polyster powder coated die-cast aluminium housing duly powder coated with PC lens. Luminaire should be available with 10° beam angle option. All external hardware must be of SS304 grade. LM 80-08 compliant LEDs of EMC/ceramic package of wattage of 5W from reputed makes should be provided. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Maximum LENS dome top temperature shall be less than 95°C at 45°C ambient temperature. Luminaire shall have an IP66 and IK10 protection. It should be capable to operating under ambient temperature range of 0°C to +45°C. The LED shall be compliant with LM80-08 standard with L70 life of 5000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used be with CCT 3000°K / 4000°K / 5700°K / 6500°K (As per ANSI Bin), CRI of Minimum 70 and SDCM < 5. LEDs must be driven at max 70% of the rated current. MCPB with Aluminium core and copper thickness of 35 micron to be used for LED mounting. LED Driver shall be silicone potted, Integrated type, Isolated, Constant Current with range 150-270V AC. Driver Efficiency > 90% & 6 KV internal surge protection with additional 10KV SPD mounted inside armature and firmly fixed to the housing. Power factor greater than 0.95 and total harmonic distortion (THD) of less than 10% should be integral to the luminaire. LED Driver must have short circuit, open circuit, Auto cut-off protection for low and high input voltage. Individual drivers should be provided with individual modules along with ventilated enclosure to hide the wirings. Driver must be with Aluminium casing. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL authorized lab to verify above parameters. Compliance to Indian Standards of IS10322 Part 5 / Section 5:1967; 16105 : 2012; IS 16106 : 2012; IS 15885 (Part2/Sec1) : 2012; IS 16108 : 2012. |
| 48 | Supplying and Laying of following size XLPE insulated PVC outer sheathed armoured aluminium Conductor/Copper cable suitable for rated voltage of 1100 Volts ISI marked conforming to IS : 7098-1988 with upto date amendments i/c laying direct in existing DWC/GI/Hume pipe, connection complete etc. as reqd. |
| 49 | 3 x 10 Sq.mm (Copper conductor armoured cable for motor to aviation light) |
| 50 | 3.5 x 25 sq.mm (Aluminium armoured cable) |
| 51 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 52 | 3 X 10 sq. mm (22mm) |
| 53 | 3½ X 25 sq. mm (28mm) |
| 54 | Supply, installation, testing & commissioning of Outdoor type Feeder Pillar panel suitable for 415 V, 3 phase ,4 wire 50 Hz AC supply system fabricated in compartmentalized & segregated design from CRCA sheet steel of 2 mm thick for frame work and 1.6 mm for covers, with 3 mm gland plates i/c cleaning & finishing complete with powder coating in approved shade, Having 4 strip aluminium bus bar of 350 Amp capacity double door with locking arrangement for protection from rain, dust, final fixed on M.S. Angle iron frame work of size 50 mm x 50 mmx 6 mm and 90 cm long legs out of which 40 cm duly grounded in cement concrete, entire panel shall have a common aluminum earth bar of size 25 mm x5mm at the rear with 2 Nos. earth stud, solid connection form main bus bar to switch gear with required size of Alu. bus bar & control wiring with 1.5 sqmm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates, duly grouted in cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Stone aggregate 20 mm) and having following accessories mounted inside the cubical panel board i/c making connection, interconnection with aluminium thimbles & duly painted with one coat of red oxide & two coats of superior quality enamel paint complete etc. as required. (The panel should by fabricated from CPRI approved manufacturer) |
| 55 | Providing & Fixing of following electrical accessories/switches etc in the above existing Replaced Feeder Pillar including making connection testing, commissioning etc. complete as reqd. (In Above) |
| 56 | 6 A, to 32 A, ratings, SP MCB, \\"C\\" curve, 10 KA breaking capacity |
| 57 | 6 A, to 32 A, ratings, TP MCB, \\"C\\" curve, 10 KA breaking capacity |
| 58 | 6 A, to 32 A, ratings, TPN MCB, \\"C\\" curve, 10 KA breaking capacity |
| 59 | 3 pole MNX Contactor 12 Amp |
| 60 | Digital Volt Meter (0-500) with selector switch |
| 61 | Digital Ammeter (0-600) with selector switch |
| 62 | CT (125/5) |
| 63 | LED Indicator Lamp |
| 64 | Digital Timer |
| 65 | Danger Plate |
| 66 | SITC of 75 VA Double Aviation obstruction Light complete with neon lamp light set fitting, comprising an aluminium housing with polycarbonate enclosure, including all necessary accessories and arrangements for mounting/fixing the light on the existing flag mast using Hydra crane or equivalent equipment. The item shall also include necessary wiring, termination, testing, and making necessary electrical connections with the existing system, complete in all respects. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender