Defence Statutory Bodies & Commissions/Committees Closing in 0 days TDR #58175659

Tender For Provn Of Toilet Hard Standing And Security Lights Near Qm Office Of 17 Corps Zone Wksp Under Ge Narangi

Issued by Statutory Bodies & Commissions/Committees · Kamrup Metro, Assam
Tender Value
43.59 Lakhs
Estimated cost
Bid Submission
19 Nov 2026
0 days left
EMD
87192
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender for Provn Of Toilet Hard Standing And Security Lights Near Qm Office Of 17 Corps Zone Wksp Under Ge Narangi

Corrigendum

Sr No Corrigendum Date Corrigendum Type New Submission Date
1 12-Nov-2026 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 19-Nov-2026

BOQ

Name of Work:- PROVN OF TOILET HARD STANDING AND SECURITY LIGHTS NEAR QM OFFICE OF 17 CORPS ZONE WKSP UNDER GE NARANGI
Sl. No. Item Description
1Surface excavation n exc 30 cm deep and average 15 cm in soft/loose soil and getting out in Soft / Loose soil etc complete all as specified and as directed.
2Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in Soft / Loose etc complete all as specified and as directed.
3Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed.
4Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and getting out in soft / loose soil etc complete al as specified and as directed.
5Spreading and levelling in layers n exc. 25 cm thick incl well ramming including watering as required etc complete all as specified and as directed.[Notes : Earth reqd for filling under floor obtained from Item no 1 and 2]
6Removing excavated material not exc 50.00 mtre and depositing where directed. at a level not exc 1.5 mtr above the starting point etc complete all as specified and as directed.
7M&L for Hard core with broken stone or boulder of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick water and rammed to a true surfac etc all as specified and as directed.
8M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area etc complete all as specified and as directed.
9M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) etc complete all as specified and as directed.
10M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface etc complete all as specified and as directed.
11M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area etc complete all as specified and as directed.
12M&L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall etc complete all as specified and as directed.
13M&L for plain cement concrete (1:4:8) type D-2, with using 40 mm graded stone aggregates as in foundations and mass concrete etc complete all as specified and as directed.
14M&L for cement concrete (1:3:6) type C-2 (using 20mm graded aggregate) as in hold fast of chowkat etc complete all as specified and as directed.
15M&L for cement concrete (1:2:4) type, B1 using 20 mm graded stone aggregates as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.
16M&L for providing plain cement concrete (1:2:4) type B-0 with using 12.50 mm graded stone aggregate as in surface channels and drains complete all as specified and directed.
17M&L for Pre-cast cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes / drain cover etc) and similar work including necessary form work and set in CM (1:6) etc complete all as specified and directed.
18Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and as directed.
19M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in Foundation, including rafts, footings, plinth beam etc complete all as specified and as directed.
20M&L for Reinforced cement concrete M-25 (desing mix) with using 20 mm graded stone aggregates as in slab supported on walls, beam and columns in floors, roofs landing balconies canopies etc complete all as specified and as directed.
21M&L for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in Chajja etc complete all as specified and as directed.
22M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed.
23M&L for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in col, pillars, piers, posts and struts etc complete all as specified and as directed.
24Supply only Liquid water proofing compound complete all as specified and as directed.
25M&L Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) etc complete all as specified and as directed.
26M&L Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) etc complete all as specified and as directed.
27M&L Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in Cm (1:4) etc complete all as specified and as directed.
28M&L for Damp proof course 40 mm thick in cement concrete (1:2:4) type B-0 to horizontal or vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m etc complete all as specified and as directed.
29M&L for Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of green marble complete all as specified and as directed.
30M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.
31M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to etc complete all as specified and as directed.
32M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) with Rough finished surfaces of concrete (Flat) etc including edges of roof slab etc complete all as specified and as directed.
33M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edge, rough finished surfaces of concrete etc complete all as specified and as directed.
34M&L for formwork to sides and soffits of floor or roof beam, beam and haunching, girders, bressummers, lintels cantilevers, shelves including supports, overhangs etc also splays between floor and beam with rough finished etc complete all as specified and as directed.
35S&F 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed.
36S&F Factory made single extruded WPC (Wood Polymer Composite) coloured solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant etc complet all a specified and as directed.
37S&F 35mm thick Providing and fixing factory made single extruded coloured WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, etc complete all as specified and as directed.
38Supply and fixing factory made uPVC white colour Three track three panels sliding window/ Vent with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. Comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed. by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) [Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made]
39S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed.
40S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed.
41S & F 100mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed..
42S&F Mild Steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed.
43S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed.
44S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple etc complete all as secified and as directed.
45M&L for framed work as in grills, grating etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed balusters walks ways, railing framed work of water tanks and similar work etc complete all as specified and as directed.
46M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed.
47All as per item No 46 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed.
48S&F Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed.
49M&L for 75 mm thick PCC (1:3:6), type C-1, using 20 mm graded aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade \\"A\\" complete all as specified and directed.
50M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed.
51M&L for Sand filling under floors or in foundations including watering and consolidation all as specified and directed.
52M&L for Rubber Moulded glossy finished pre-cast concrete interlocking coloured paving Block of glass fibre reinfoced vibro compacted any shape and size confirming to IS-15658-2006 of 60 mm thick, M-35 grade to match with grey cement and pigment etc complete all as specified and as directed.
53M&L for cement concrete type B-0 (1:2:4) (12.5mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed.
54M&L for Rendering 10 mm thick in CM (1:3) for backing coat of tiles / dado etc complete all as specified and as directed.
55M&L for Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes etc complete all as specified and as directed.
56M&L Glazed ceramic tiles (Coloured) as in vertical surface 600X1200mmX7 to 9 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and as directed.
57M & L for Non - skid joint free matt finished ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed.
58M&L for rendering for ceiling 5 mm thick in CM (1:3) on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed.
59M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surface finished and smooth without using extra cement etc complete all as specified and as directed.
60M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed.
61M&L for rendering 15 mm thick in CM (1:4) on other than fair faces of brick work or concrete surface mixed with water proofing compound where ever is reqd as per manufacture instruction finished even and smooth without using extra cement etc complete all as specified and as directed. Notes : WPC shall be measured and paid seperately
62M&L for 10 mm cement plastering in CM (1:3) as in horizontal and vertical surface of brick work or concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed. Notes : WPC shall be measured and paid seperately
63M&L for applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017, 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed.
64S&F Steel work as in tubular trusses as in col, rafters, purlins etc. complete using ERW or induction butt welded tubes etc complete all as specified and as directed.
65M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe.290.Gde-E-165 etc complete all as specified and as directed.
66S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.
67S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.
68S&F 18mm thick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in wall panelling / cub board shutter, Kitchen shelves and modular kitchen shutter, shelves, drawers etc over 0.90 mm thick decorative laminate type 1, of surface finish (both side of shutter), colour and pattern as approved, fixed with approved adhesive as per maker's instructions etc complete all as specified and as directed.
69M&L for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed.
70M&L for Preparing new plastered suface of walls and applying two coats distemper oil emulsion, white or tinted over a coat of primer etc complete all as specified and as directed.
71M&L for preparation Newly plastered surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance (Apex Ultima), dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces etc complete all as specified and as directed.
72M&L for preparing newely plastered surface of ceiling and applying two coats distemper oil emulsion, white or tinted over a coat of primer etc complete all as specified and as directed.
73S&F 4mm thick sheet Figured glass, pin head type and glazing with oil putty in squares in not exc 0.5 sq.m in each pane etc complete all as specified and as directed.
74M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.
75S&F vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat , black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed.
76S&F Viterous china squatting pan orrisa pattern of size 580X440 mm white with integral foot rest 'P' trap including connecting to trap incl S trap or P trap and flush pipe anti-symphonage pipe etc complete all as specified and as directed.
77S&F Oval shpaped vitreous china wash basin white, flat back, size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets and including, 32 mm bore waste CP coupling and 32mm bore LDPE pipe 600 mm long and 15 mm bore 450 mm long PVC connection etc complete all as specified and directed.
78S&F Viterous China urinals, Full Stall stall type, complete including providing and fixing plugs, beddings urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, incl urinal spreader 15 mm bore, suitable size of 15 mm bore PVC connection 450 mm long and 40 mm dia bore 600 mm long LDPE incl 40 mm dia bore waste coupling etc complete all as specified and as directed.
79S&F PVC deo flushing cistern valveless with flushing out valve low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets & connection to pipe etc 15 mm dai bore PVC connection 450 mm long complete all as specified and as directed.
80S&F 15 mm dia bore Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.
81S&F 15 mm Centre hole Basin mixture W/o Pop Up all as specified and as directed.
82S&F 15 mm dia bore Bib Cock long body with wall falnges of Cat Part No - P-6808 of Marco series of Prayag incl fixing etc complete all as specified and as directed.
83S&F 15 mm dia bore CP fancy type long body Angular stoop cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed of Cat Part No - P-6808 of Marco series of Prayag etc complete all as specified and as directed.
84S&F Bib Cock 2 way double handle with CP flange fancy type long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed etc of Cat Part No - P-6812 of Marco series of Prayag etc complete all as specified and as directed.
85S&F in bevelled edge looking mirror 7 to 8 mm thick area exc 1.0 sqm but not exc 1.50 sqm mirror of selected quality glass fixed with 4 nos of Studs incl polishing the edges etc complete all as specified and as directed.
86&F 15 mm dia bore Brass health faucet with 1.00 mtr tube & hookd incl fixing etc of Cat Part No -CPHF-6 of Prayag etc complete all as specified and as directed.
87S&F Jet Spreay SS-20 (Butterfly) with 1.0 mtr tube incl fittings of Cat Part No -CPJ-5 of Prayag etc complete all as specified and as directed.
88S&F ABS soap dish with brass stand of Cat Part No -CAP-4 of Parayag series incl fixing etc complete all as specified and as directed.
89S&F 125mm bore dia Stainless steel shower roses with arms with or without swivel joints, any size, including fixing to steel pipe or union etc Cat Part No -CHOH-8 of Parayag series incl fixing etc complete all as specified and as directed.
90S&F Corner Glass Shelf (with brass bracket Bracket) of 200mm long of Cat Part No - DAP-29 of prayag series incl fixing etc complete all as specified and as directed.
91S&F Glass Shelf 300mm Long of Cat Part No - CPA-32 of Prayag Series series incl fixing etc complete all as specified and as directed.
92S&F Stainless Steel Towel Rail Cubix of Cat Part No - CPA-46 of Prayag series incl fixing etc complete all as specified and as directed.
93S&F Brass Towel ring with Round Flange of Cat Part No - CPA-2 of Prayag Jaquar series incl fixing etc complete all as specified and as directed.
94S&F GI Tubes, 15 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.
95S&F GI Tubes, 20 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.
96S&F rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs incl 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic etc complete all as specified and directed.
97S & F 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and as directed.
98S&F 75 mm dia bore PVC (SWR) multi floor trap with grating including jointing with solvent cement etc complete all as specified and as directed.
99S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed.
100S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed.
101S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc complete all as specified and directed.
102S&F PVC bends (any radius) of 110mm dia with access door etc complete all as specified and as directed.
103S&F PVC bends (any radius) of 75mm dia with access door etc complete all as specified and as directed.
104S&F 110 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed.
105S&F 75 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed.
106S&F PVC vent cowls of 110mm dia etc complete all as specified and as directed.
107M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate complete all as specified and directed.
108M&L for laying of PVC (SWR) 150 mm (Internal dia of pipes) single socketed, in any length with rubber ring joints, laid in trenches or in floors etc complete all as specified and directed.
109M&L Soakage wells excavation, in any type of soil, foundation in PCC (1:3:6), walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size of sokage well (1.80 mtr dia X3.00 mtr deep) etc complete all as specified and directed.
110M&L Polyethylene Septic Tank of 50 user, Black Colour, Diameter of pipe 1600mm, length 3200, wall thickness 16mm, no of chamber 03 nos , no of maholes 0-2 nos, size of manhole 550mm dia with 160mm dia int let and out let pipe with Provn of Air Vent pipe incl fixing arrangement etc complete all as specified and as directed. Notes : Excn, PCC RFR and Removal shall be measured and paid sepaterly under relevant items
111M&L Point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in and including PVC Conceled Conduit with all accessories including fabricated MS/PVC terminal boxes fixed flush box and cover plate ( for modular Switch socket ) with wall surface for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as directed.
112S&F switch modular type 6 Amp 240 Volts single one way (ISI marked).
113S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as directed.
114Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified.
115Supply and fixing in repair LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.
116S & F in repair LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.
117Supply & fix MCB DB of sheet metal enclosure double door SPN 8 way with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate all as directed.
118S&F MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and directed.
119S&F in repair/replacement MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified.
120Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified.
121S&F in repair/replacement LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and directed.
122M&L for street light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 1.5.0 mtrs complete all as specified and directed.
123Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009.
124S& F steel tubes medium grade galvanised 20 mm bore with all fittings and fixed complete to walls and ceilings and laid in floors complete all as directed.
125S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and directed.
126Cutting existing steel tubing of 40mm for alterations or additions complete all as directed by engineer-in-charge.
127Supply & Laying in trenches or fixing on wall or passing through pipe or in cable ducts, 1100 volts grade 3.5/4.0 core XLPE(FRLS) , armoured, electric power cables (heavy duty) with aluminium conductor of Size 10x4 core complete all as specified.
128M&L for erection of steel tubular steel tubular swaged pole type 410 SP - 31 (9.00 metres long) including cast iron base plate, finial taper plug and and painted with two coat of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.
129M&L for connection of junction box to street light luminaire using wiring with two runs (P-N) of single core 1.5 Sqmm (nominal area) FR PVC insulated and unsheathed multi-stranded copper conductor cable 1100 volts grade and one run of FR PVC insulated and unsheathed multi-stranded copper conductor of size 1.5sqmm single core as earth continuity wire drawn through PVC conduit(Heavy grade) and tiding the same by aluminium strip with the pole complete all as specified and directed. (Note : Two single core 1.5 Sqmm cable and one single core 1.5 Sqmm earth conductor cable and one run of PVC conduit shall be measured as one run)
130Supply and fix street light junction box of size made of high quality polycarbonate with IP-66 protection (Dust and vermin proof according to IEC-60529) Totally insulated made of halogen and silica free recyclable material having high quality gasket made out of polyurethane with MCB, DP, 10KA, 6 Amps to be fixed on Din rail , with locking arrangement with cable gland suitable upto 16 sqmm cable and necessary fixing arrangements such as clamps, nuts, bolts etc all as specified & directed by Engr-in-Charge.
131Excavating in trenches, n exc 1.5 m wide and exc 1.5 m but n exc 3.0 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.
132M&L for cement concrete (1:4:8) type D-2 using 40 mm graded crushed stone aggregate as in foundation complete all as specified and directed by Engineer- in-charge.
133M&L for PCC (1: 3 : 6) type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in mass concrete including necessary form work for coping to the new/existing Steel Poles complete all as specified and directed.
134Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.
135M&L for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified. Please Enable Macros to View BoQ information
136M&L for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 58175659
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 43.59 Lakhs
LAST DATE 19-11-2026
Authority
Authority Name Military Engineer Services
Work Description Tender for Provn Of Toilet Hard Standing And Security Lights Near Qm Office Of 17 Corps Zone Wksp Under Ge Narangi
Basic Detail
Tender No 8296/B/E8
Bidding Type Tender
Location
City Kamrup Metro
State Assam
Key Dates
Publish Date 12 Nov 2026
Submission Date 19 Nov 2026
Open Date 21 Nov 2026
Finance
Tender Value 43.59 Lakhs
Tender Fee 500
EMD 87192
Exemption Available
Document List
3c7110fa-d801-49d4-90a3-ae979e4896d3.html
8296Tender.pdf
BOQ_892124.xls
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Nov 12, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Nov 19, 2026
18:00 IST

Corrigendum-1 Issued

Clarifications on tender conditions and amendments issued.

Today
Nov 19, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Today
Nov 21, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 2 days

Tender Documents

Download All (ZIP) ↓
html

3c7110fa-d801-49d4-90a3-ae979e4896d3.html

pdf

8296Tender.pdf

xls

BOQ_892124.xls

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender