Tender For Providing Of Toilet Block Near 51 Sub Area Sig Pl Under Ge Narangi
Tender Value
43.68 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
15 days left
EMD
87376
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of Toilet Block Near 51 Sub Area Sig Pl Under Ge Narangi
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n exc 30 cm deep and average 15 cm in soft/loose soil and getting out in Soft / Loose soil etc complete all as specified and as directed |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in Soft / Loose etc complete all as specified and as directed |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed |
| 4 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and getting out in soft / loose soil etc complete al as specified and as directed |
| 5 | Spreading and levelling in layers n exc. 25 cm thick incl well ramming including watering as required etc complete all as specified and as directed Notes : Earth reqd for filling under floor obtained from Item no 1 and 2 |
| 6 | Removing excavated material not exc 50.00 mtre and depositing where directed at a level not exc 1.5 mtr above the starting point etc complete all as specified and as directed |
| 7 | Material and labour for Hard core with broken stone or boulder of gauge not exc 63mm, deposited, spread and levelled in layers not exc 15 cm thick water and rammed to a true surfac etc all as specified and as directed |
| 8 | Material and labour for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area etc complete all as specified and as directed |
| 9 | Material and labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) etc complete all as specified and as directed |
| 10 | Material and labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface etc complete all as specified and as directed |
| 11 | Material and labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area etc complete all as specified and as directed |
| 12 | Material and labour for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall etc complete all as specified and as directed |
| 13 | Material and labour for Sand filling under floors or in foundations including watering and consolidation all as specified and directed |
| 14 | Material and labour for plain cement concrete 1:4:8 type D-2, with (using 40 mm graded stone aggregates) as in foundations and mass concrete etc complete all as specified and as directed |
| 15 | Material and labour for cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in hold fast of chowkat etc complete all as specified and as directed |
| 16 | Material and labour for cement concrete 1:2:4 type, B1 (using 20 mm graded stone aggregates) as in copings, Chajja kerbs, roof padding/staging of water tank etc including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed |
| 17 | Material and labour for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in Foundation, including rafts, footings, plinth beam etc complete all as specified and as directed |
| 18 | Material and labour for Reinforced cement concrete M-25 (desing mix) with using 20 mm graded stone aggregates as in slab supported on walls, beam and columns in floors, roofs landing balconies canopies etc complete all as specified and as directed |
| 19 | Material and labour for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in Chajja etc complete all as specified and as directed |
| 20 | Material and labour for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed |
| 21 | Material and labour for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in col, pillars, piers, posts and struts etc complete all as specified and as directed |
| 22 | Material and labour for providing plain cement concrete 1:2:4 type B-0 with (using 12.50 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed. |
| 23 | Material and labour for Pre-cast cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate ) as in landings, cover slab (for manholes / drain cover etc) and similar work including necessary form work and set in CM 1:6 etc complete all as specified and directed. |
| 24 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed |
| 25 | Supply only Liquid water proofing compound |
| 26 | Material and labour Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 etc complete all as specified and as directed |
| 27 | Material and labour Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 etc complete all as specified and as directed |
| 28 | Material and labour Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in Cm 1:4 etc complete all as specified and as directed |
| 29 | Material and labour for Damp proof course 40 mm thick in cement concrete 1:2:4 type B-0 to horizontal or vertical surfaces including necessary formwork and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m etc complete all as specified and as directed. |
| 30 | Material and labour for green Marble work ( 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete ncl grinding the edges half round incl polishing complete all as specified and as directed. |
| 31 | Material and labour for 20 mm thick Granite (of any type) work (table rubbed and polished in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite incl grinding the edges half round incl polishing etc complete all as specified and as directed. |
| 32 | Material and labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to etc complete all as specified and as directed |
| 33 | Material and labour for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) with Rough finished surfaces of concrete (Flat) etc including edges of roof slab etc complete all as specified and as directed |
| 34 | Material and labour for Formwork to chullah hoods, chajjas, troughs and similar items including edge, rough finished surfaces of concrete etc complete all as specified and as directed |
| 35 | Material and labour for formwork to sides and soffits of floor or roof beam, beam and haunching, girders, bressummers, lintels cantilevers, shelves including supports, overhangs etc also splays between floor and beam with rough finished etc complete all as specified and as directed |
| 36 | Supply and fix 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed |
| 37 | Supply and fix Factory made single extruded WPC (Wood Polymer Composite) coloured solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant etc complet all a specified and as directed |
| 38 | Supply and fix 35mm thick Providing and fixing factory made single extruded coloured WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, etc complete all as specified and as directed |
| 39 | Supply and fixing factory made uPVC white colour Three track three panels sliding window/ Vent with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. Comprising of uPVC multi chambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 40 | Supply and fix aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed |
| 41 | Supply and fix aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed |
| 42 | Supply and fix 100mm size Butt hinges, medium weight, cold rolled mild steel, and fixed etc complete all as directed. |
| 43 | Supply and fix Mild Steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate etc complete all as specified and as directed |
| 44 | Supply and fix 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed |
| 45 | Supply and fix stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staple etc complete all as secified and as directed |
| 46 | Material and labour for framed work as in grills, grating etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed balusters walks ways, railing framed work of water tanks and similar work etc complete all as specified and as directed |
| 47 | Material and labour for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed |
| 48 | All as per item No 47 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed |
| 49 | Supply and fix Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with double rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed |
| 50 | Material and labour for 75 mm thick PCC 1:3:6, type C-1, using 20 mm graded aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade \\"A\\" complete all as specified and directed. |
| 51 | Material and labour for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed |
| 52 | Material and labour for Rubber Moulded glossy finished pre-cast concrete interlocking coloured paving Block of glass fibre reinfoced vibro compacted any shape and size confirming to IS-15658-2006 of 60 mm thick, M-35 grade to match with grey cement and pigment etc complete all as specified and as directed |
| 53 | Material and labour for cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed |
| 54 | Material and labour for Rendering 10 mm thick in CM 1:3 for backing coat of tiles / dado etc complete all as specified and as directed |
| 55 | Material and labour for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed |
| 56 | Material and labour for Screed bed or bedding layer of mortar 15 mm thick in CM 1:6 for laying floor finishes etc complete all as specified and as directed |
| 57 | Material and labour Glazed ceramic tiles (Coloured) as in vertical surface 600X1200mmX7 to 9 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and as directed |
| 58 | Material and labour for Non - skid joint free finished ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed |
| 59 | Material and labour for rendering for ceiling 5 mm thick in CM 1:3 on fair faces of brick work or concrete surface finished even and smooth without using extra cement etc complete all as specified and as directed |
| 60 | Material and labour for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surface finished and smooth without using extra cement etc complete all as specified and as directed |
| 61 | Material and labour for rendering 15 mm thick in CM (1:4) on other than fair faces of brick work or concrete surface mixed with water proofing compound where ever is reqd as per manufacture instruction finished even and smooth without using extra cement etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately |
| 62 | Material and labour for 10 mm cement plastering in CM (1:3) as in horizontal and vertical surface of brick work or concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately |
| 63 | Material and labour for applying APP modified water proofing membrane as per IS 1654-2017/IS 16352-2017, 3mm thick and weighing not less than 3.60kg/Sqm reinforced with non woven polyster/HMHDPE matt black finished over compatible primer/bonding bitumen @ 0.40 Litr/Sqm and torch applications of membrane with 75mm side overlap and 100mm end lap after necessary preparation of surface complete as per manufacturer's instructions and applying a coat of solar reflective bituminous aluminum paint on top @ 0.10 litre/sqm complete all as specified and directed. complete all as directed. |
| 64 | Supply and fix Steel work as in tubular trusses as in col, rafters, purlins etc. complete using ERW or induction butt welded tubes etc complete all as specified and as directed |
| 65 | Material and labour for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe.290.Gde-E-165 etc complete all as specified and as directed |
| 66 | Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as complete all as specified and as directed. |
| 67 | Supply and fix pre-painted hot dip aluminium zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick (total coated thickness), any patteren corresponding to IS 15965: 2012 of durability class 3, four (4) coat atmospheric classification category 3, coating class AZ 150 of an approved colour havingb yield strength of 550MPa as in roof covering/wall cladding, fixed with self tapping screws as specified and as directedNote: To be executed for provison of ridges and hips, valley etc complete all as specifed and as directed |
| 68 | Supply and fix 18mm thick Block boards, grade 1 quality, exterior grade, commercial type, Water proof, termite proof, fixed with screws to timber frame-work as in wall panelling / cub board shutter, Kitchen shelves and modular kitchen shutter, shelves, drawers etc over 0.90 mm thick decorative laminate type 1, of surface finish (both side of shutter), colour and pattern as approved, fixed with approved adhesive as per maker's instructions etc complete all as specified and as directed |
| 69 | Material and labour for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed |
| 70 | Material and labour for Preparing new plastered suface of walls and applying two coats acrylic distemper white or tinted over a coat of primer etc complete all as specified and as directed |
| 71 | Material and labour for preparation Newly plastered surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance (Apex Ultima), dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. etc complete all as specified and as directed |
| 72 | Material and labour for preparing newely plastered surface of ceiling and applying two coats of acrylicdistemper white or tinted over a coat of primer etc complete all as specified and as directed |
| 73 | Supply and fix 4mm thick sheet Figured glass, pin head type and glazing with oil putty in squares in not exc 0.5 sq.m in each pane etcc omplete all as specified and as directed |
| 74 | Material and labour for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed |
| 75 | Supply and fix vitreous china wash down water closet pan (Pedestal Pan) including fixing bolts, flush pipe anti syphonage pipe, plastic water closet seat , black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device etc, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device etc complete all as specified and as directed |
| 76 | Supply and fix Viterous china squatting pan orrisa pattern of size 580X440 mm white with integral foot rest 'P' trap including connecting to trap incl S trap or P trap and flush pipe anti-symphonage pipe etc complete all as specified and as directed |
| 77 | Supply and fix Oval shpaped vitreous china wash basin white, flat back, size 550 x 400mm excluding taps, waste, chain & plug and porcelain stopper but including brackets and including, 32 mm bore waste CP coupling and 32mm bore LDPE pipe 600 mm long and 15 mm bore 450 mm long PVC connection etc complete all as specified and directed. |
| 78 | Supply and fix Viterous China urinals, Full Stall stall type, complete including providing and fixing plugs, beddings urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing with brackets, flush pipe, incl urinal spreader 15 mm bore, suitable size of 15 mm bore PVC connection 450 mm long and 40 mm dia bore 600 mm long LDPE incl 40 mm dia bore waste coupling etc complete all as specified and as directed |
| 79 | Supply and fix PVC deo flushing cisrern valveless with flushing out valve low level of 10 Ltr capacity white with inlet ball valve, float, flushing bend & handle including brackets & connection to pipe etc 15 mm dai bore PVC connection 450 mm long complete all as specified and as directed |
| 80 | Supply and fix 15 mm dia bore Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed . |
| 81 | Supply and fix 15 mm dia Centre hole Basin mixture W/o Pop Up complete all as specified and directed . |
| 82 | Supply and fix 15 mm dia bore Bib Cock long body with wall falnges etc complete all as specified and as directed |
| 83 | Supply and fix 15 mm dia bore CP fancy type long body Angular stoop cock cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed |
| 84 | Supply and fix Bib Cock 2 way double handle with CP flange fancy type long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed etc complete all as specified and as directed |
| 85 | Supply and fix bevelled edge looking mirror 7 to 8 mm thick area exc 1.0 sqm but not exc 1.50 sqm mirror of selected quality glass fixed with 4 nos of Studs incl polishing the edges etc complete all as specified and as directed |
| 86 | Supply and fix 15 mm dia bore Brass health faucet with 1.00 mtr tube & hookd incl fixing etc complete all as specified and as directed |
| 87 | Supply and fix Jet Spreay SS-20 (Butterfly) with 1.0 mtr tube incl fittings complete all as specified and as directed |
| 88 | Supply and fix ABS soap dish with brass stand complete all as specified and as directed |
| 89 | Supply and fix 125mm bore dia Stainless steel shower roses with arms with or without swivel joints, any size, including fixing to steel pipe or union etc complete all as specified and as directed |
| 90 | Supply and fix Corner Glass Shelf (with brass bracket Bracket) of 200mm long complete all as specified and as directed |
| 91 | Supply and fix Glass Shelf 300mm Long complete all as specified and as directed |
| 92 | Supply and fix Stainless Steel Towel Rail complete all as specified and as directed |
| 93 | Supply and fix Brass Towel ring with Round Flange complete all as specified and as directed |
| 94 | Supply and fix GI Tubes, 15 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed |
| 95 | Supply and fix GI Tubes, 20 mm dia bore of pies 'medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed |
| 96 | Supply and fix rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I capacity of tank 1000 ltrs incl 25 mm dia of bore ball float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic etc complete all as specified and directed |
| 97 | Supply and fix 20 mm gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and including complete all as specified and directed |
| 98 | Material and labour for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate complete all as specified and directed. |
| 99 | Material and labour for Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size of sokage well (1.80 mtr dia X3.00 mtr deep) etc complete all as specified and directed |
| 100 | Material and labour for Polyethylene Septic Tank of 50 user, Black Colour, Diameter of pipe 1600mm, length 3200, wall thickness 16mm, no of chamber 03 nos , no of maholes 0-2 nos, size of manhole 550mm dia with 160mm dia int let and out let pipe with Provn of Air Vent pipe incl fixing arrangement etc complete all as specified and as directed Notes : Excn, PCC RFR and Removal shall be measured and paid sepaterly under relevant items |
| 101 | Material and labour for laying of PVC (SWR) 150 mm (Internal dia of pipes) single socketed, in any length with rubber ring joints, laid in trenches or in floors etc etc complete all as specified and directed |
| 102 | Supply and fix 75 mm dia bore PVC (SWR) multi floor trap with grating including jointing with solvent cement etc complete all as specified and as directed |
| 103 | Supply and fix 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laidin trenches or in floors etc complete all as specified and directed |
| 104 | Supply and fix 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laidin trenches or in floors etc complete all as specified and directed |
| 105 | Supply and fix 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls etc complete all as specified and directed |
| 106 | Supply and fix PVC bends (any radius) of 110mm dia with access door etc complete all as specified and as directed |
| 107 | Supply and fix PVC bends (any radius) of 75mm dia with access door etc complete all as specified and as directed |
| 108 | Supply and fix 110 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed |
| 109 | Supply and fix 75 mm dia bore PVC (SWR) junction single, (Single T) equal or unequal with access door etc complete all as specified and as directed |
| 110 | Supply and fix PVC vent cowls of 110mm dia etc complete all as specified and as directed |
| 111 | Material and labour Point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FR-LSH grade cable conforming to IS-694 1990 drawn in and including PVC Conceled Conduit with all accessories including fabricated MS/PVC terminal boxes fixed flush box and cover plate ( for modular Switch socket ) with wall surface for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and as directed. |
| 112 | All as per item serial No 111 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches complete all as specified and as directed. |
| 113 | All as per item serial No 111 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and as directed. |
| 114 | Supply and fix switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and as directed. |
| 115 | Supply and fix modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 116 | Supply and fix modular switch 1 way 16 amp, 1 module complete all as specified and as directed. |
| 117 | Supply and fix modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 118 | Supply and fix ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as specified and as directed. |
| 119 | Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. |
| 120 | Supply and fix LED light fitting with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 121 | Supply and fix LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 122 | Supply and fix MCB DB of sheet metal enclosure IP-43 double door SPN 8 way with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and as directed. |
| 123 | Supply and fix MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 124 | Supply and fix MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and as directed. |
| 125 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and as directed. |
| 126 | Supply and fix LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and directed. |
| 127 | Material and labour for building secruity light bracket made out of 40 mm bore light grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed. |
| 128 | Material and labour for Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 |
| 129 | S& F steel tubes medium grade galvanised 20 mm bore with all fittings and fixed complete to walls and ceilings and laid in floors complete all as directed. |
| 130 | Supply and fix Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and directed |
| 131 | Cutting existing steel tubing of 40mm for alterations or additions complete all as specified and directed |
| 132 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.0 sq mm 2 core complete all as specified and directed |
| 133 | Material and labour for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender