Tender For Construction Of Additional Class Room With Ver. At Govt Middle School Gabber Zone And District Reasi.
Tender Value
10.42 Lakhs
Estimated cost
Bid Submission
11 Nov 2026
10 days left
EMD
20840
Bank guarantee accepted
Document Fee
600
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Reasi → Jammu and Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Additional Class Room With Ver. At Govt Middle School Gabber Zone And District Reasi.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on an) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil : |
| 2 | Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 min width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan,including dressing of sides andramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed:All kinds of soil : |
| 3 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement: 4 coarse sand: 8 graded stone aggregate 40mm nominal size) Crushed . |
| 4 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1.1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) |
| 5 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) with 20% boulder. |
| 6 | Reinforcement of R.c.c work in plinth band incl. straightening, cutting, bending, placing in position and binding all complete. |
| 7 | Brick work with F.P.S bricks of class designation 75 in 1:6 (cement: sand) mortar. Including Extra for brick work in superstructure above plinth level (by manual mean). |
| 8 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns etc. for mass concrete |
| 9 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 10.5.1 Using M.S. angles 40x40x6mm for diagonal braces. |
| 10 | Cement plaster in 1:6 ( 1 cement:6 fine sand ) ,15 mm thick. |
| 11 | Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete50 mm thick with 20mm nominal size stone aggregate |
| 12 | Providing and fixing strips in joints of terrazzo/ cement concrete floors.Glass strips 40 mm wide and 6 mm thick |
| 13 | Applying priming coat With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel. |
| 14 | Painting of doors and windows with ready mixed synthetic enamel paint of approved brand and manufacture in all shades. |
| 15 | Distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre,two or more coats on new work of approved manufacturer, of required shade and colour complete as per manufacturer’s specifications |
| 16 | Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm) |
| 17 | Making plinth protection 50mm thick with cement conc .(1:3:6) ,20 mm nominal size of stone aggregates over 75mm bed of dry brick ballast,40mm nominal size of well rammed and consolidated and grouted with fine sand including finishing the top smooth. |
| 18 | Structural steel work in built up section,trusses and framed work,including cutting,hoisting fixing in position and applying a priming coat of approved steel primer all complete. |
| 19 | Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 20 | Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 21 | Providing wood work in false ceiling, partitions etc sawn & putup in position budloo/ Fir wood |
| 22 | Providing and fixing flat pressed 3 layers medium density partical board or graded particles board(Grade-1) IS:3087 marked(Novapan,Ecoboard or Bhutan board etc.) in ceiling with necessaty nails etc complete.6MM |
| 23 | Providing and fixing plained eaves boarding 250x32 mm (nominal size ). |
| 24 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete 250x16 mm |
| 25 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :100x10mm |
| 26 | Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :200x10mm |
| 27 | Electric wiring with 1.5sq mm copper cabble including 20mm dia 2mm thick PVC pipe 5amp switch sukan box and connection to the main pole complete as directed by engineer in charge |
| 28 | Write Name of the School and LOGO of Samagra Shiksha. |
| 29 | Carriage of Sand by mechanical transport including loading , unloading & stacking complete lead upto 90 KM & manual labour 500 MTR |
| 30 | Carriage of stone aggregate below 40 mm thick by mechanical transport including loading, unloading & stacking complete lead upto 90 km & manual labour 500 MTR |
| 31 | Carriage of bricks by mechanical transpor including loading, unloading & stacking complete lead upto 90 km & manual labour 500 MTR Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender