Tender For Addition/Alteration To Bldg No P-52 And Provn Of Post Top Light Bldg No P-41 &Type -Iv Married Accommadation At Dhq-15 Icgs Okha Under Ge (I) Cg Porbandar
Tender Value
11.43 Lakhs
Estimated cost
Bid Submission
12 Nov 2026
18 days left
EMD
22860
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
porbandar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration To Bldg No P-52 And Provn Of Post Top Light Bldg No P-41 &Type -Iv Married Accommadation At Dhq-15 Icgs Okha Under Ge (I) Cg Porbandar
BOQ
| Sl. No. | Item Description |
| 1 | Schedule 'A' |
| 2 | Demolition of wall brickwork/ block masonry/ stone or boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 3 | Demolition of cement concrete un reinforeced of any description and in any position not otherwise specifically provided for,complete all as specified and directed. |
| 4 | Removing excavated material to a distance exc 1.5 km but not exc 5 km and depositing where directed at a level n exc 1.5m above the starting point. |
| 5 | Material and labor for cement concrete (1:4:8) type D2 using 40mm graded aggregate as in foundation,filling and mass concrete etc all as specified and as directed. |
| 6 | Material and labor Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6 , complete all as specified and directed |
| 7 | Material and labor for rendering on fair faces of brick work or concrete surface of wall 15mm thick in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed |
| 8 | Taking down cement plaster includiing raking out joints hacking for key and scrubbing down with water complete, all as specified and directed |
| 9 | Material and labor for 10mm thick rendering in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement using waterproocompound at 3% by weight of cement content all as specified and directed. Note: WPC will be measured and paid separately |
| 10 | Material and labor Rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling finished even and smooth without using extra cement all as specified |
| 11 | Supply only integral water proofing compound all as specified. |
| 12 | Supply and fixing of Rotational moulded polyethelyne water storage tanks of capacity 500 ltrs (cylinderical vertical with closed top) hoisted and fixed in position including dismantling of existing tank complete all as specified in SSR Part - I complete all as specified and directed |
| 13 | Supply, and fixing 15mm nominal bore Chromium Plated (CP) brass bib tap of fancy type, screw-down high-pressure pattern, conforming to relevant IS standards, providing a matching CP flange/wall cap, all complete as specified and directed by the Engineer-in-Charge |
| 14 | Supply and fixing of 15mm bore CP Stop valves/angle valve, fancy type chromium plated screwed down, high pressure, screwed both ends for iron pipe or for unions and fixed in position all complete as specified and directed by the Engineer-in-Charge |
| 15 | Supply and fixing of 20mm dia ball valves high pressure of PTMT epoxy coated aluminium rod & high density plastic ball all complete as specified and directed by the Engineer-in-Charge |
| 16 | S & F PVC connections 15 mm size with PTMT nuts of length 450mm all complete as specified and directed by the Engineer-in-Charge |
| 17 | Material and labor 20mm thick Granite (of any type) in Flooring (table rubbed and polished) and including 20 mm thick Screed Bed in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture pigments to match the shade of granite all complete as specified and directed by the Engineer-in-Charge |
| 18 | S & F in repair Sinks made of stainless steel 1mm thick kitchen with plugs,washers and wastes;including bedding in cement mortar on to dwarf wall or including cantilever brackets and connecting union to pipe,overall size 495 mm x 420 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed. |
| 19 | Material and labor Machine cut kota stone slab20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed. |
| 20 | Supply and fixing of Joint free coloured glazed ceramic tiles 350 x250 x7 mm/450 x350 x7mm/450x300mmx7 mm /250x375x7mm thick on vertical surfaces including 10mm thick backing coat in CM 1:4 such such as skirting dados and riser to step etc set jointed in neat cement slurry and pointed in white cement to match complete all as specified & direcetd. |
| 21 | Material and labor Preparing old plastered / decorated surface of ceiling surfaces and one coat of oil bound distemper including smooth roller finish with complete all as specified and directed by Engineer in Charge. (Note The scope of work includes the thorough cleaning of all floors, glass surfaces, and furniture without any extra financial implication to the Government.\\" |
| 22 | Material & Labour for Preparing old plastered / decorated surface of wall including cornices etc., by brooming down and applying one coat of oil bound distemper including smooth roller finish, complete all as specified and directed by Engineer-in-Charge. |
| 23 | Material & Labour for preparation of old plastered surfaces and applying one coat of 100% Premium Acrylic emulusion paint having VOC 50gm/litre and UV resistance as per IS 15489 : 2004, Alkali and Fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with Silicon Aditives @ 1.43 litre/10sqm, complete all as specified and directed by Engineer-in-Charge. |
| 24 | Material & Labour for Preparing new plastered surface of wall surfaces and applying two coats of oil bound distemper including smooth roller finish, complete all as specified and directed by Engineer-in-Charge. |
| 25 | Material & Labour for 3mm thick wall care putty in layers and making even and smooth of wall surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 26 | Material & Labour for Preparing new plastered / decorated surface of ceiling surfaces and applying two coats of oil bound distemper including smooth roller finish, complete all as specified and directed by Engineer-in-Charge. |
| 27 | Supply & Fixing for factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (±0.2mm). Window profile with hollow section with multi chamber, frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding interlock (one vertical length in each shutter) (45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitered cut and fusion welded at all corners, including railing of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware, EPDM gasket. 1.2 ±0.2mm thick galvanized steel frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm) 2nos, sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fastener. Hardware (touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm, 5.5 mm glass of selected quality (two number) and required accessories , area not exceeding 2.00 sqm each fixed from ground floor to height of any floors, complete all as specified and directed by Engineer-in-Charge. |
| 28 | Supply & Fixing of 7mm thick aluminium grills of make \\"Deco grill\\" model DG 104 surrounded by aluminium 'C' channel and size of opening 75x75 mm all as specified and directed fixed from ground floor to height of any floors, complete all as specified and directed by Engineer-in-Charge. |
| 29 | Supply & Fixing of 2nd class HW plain chowkhats and framed, rebated on the solid rounded or chamfered put together with glue pinned at joints, complete all as specified and directed by Engineer-in-Charge. |
| 30 | Supply & Fixing Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, with decorative face veneer on both sides with lipping/frame to match, with three number 100 mm size but hinges of extruded aluminium alloy anodisedtype B-21 ,two number aluminium anodized tower bolt of 150 mm length and 02 no handle extruded aluminium alloy handle complete all as specified and directed. |
| 31 | Material & Labour for Formwork to chullah hoods, chajjas, troughs and similar items including edges rough finished flat surfaces, complete all as specified and directed by Engineer-in-Charge. |
| 32 | Material & Labour for formwork to edges of concrete flats, treads, breaks in floors, window-cills, concrete railings, opening of concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC / PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but not exc. 20cm wide rough finished, complete all as specified and directed. |
| 33 | Material and Labour for Reinforced cement concrete (nominal mix) Type B-0, 1:2:4 (12.5 graded aggregate )in slab supported on walls,beams,& columns ,landings,balconies,canopies deck slab and in shelves ,lintel ,Chajjas , complete all as specified and directed. |
| 34 | Material & Labour for High strength mild steel CRS reinforcement bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire(annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed by Engineer-in-Charge. |
| 35 | All as per Item No 33 above but 5mm dia and over upto 10mm dia as in stirrups, spacers or binder, complete all as specified and directed. |
| 36 | Supplying and laying of 20 mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified. |
| 37 | Supply and fixing of PVC(SWR)' P' trap of 110 mm dia complete all as specified & directed. |
| 38 | S & F PVC (SWR) pipe grade ‘A’ single socketed 110 mm dia in any length, jointing with cement solvent solution, fixed to walls complete all as specified |
| 39 | Point wiring complete with 1.5 sqmm single-core PVC insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) but shall be increased as per actual site requirement in accordance with clause 19.125 of SSR part-I. ISI marked with wall thickness not less than 1.8 mm including conduit accessories like bends, tees, junction boxes etc. fixed concealed/recessed in wall or ceiling etc. including 1.5 sqmm PVC insulated but unsheathed multistranded copper conductor FRLS cable as earth continuity conductors including modular type metal flush box with cover plate and frame of required modules for mounting of modular switches, sockets, switch sockets, fan regulators with required modules all as specified etc. for the following:- |
| 40 | Supply and fixing of Point wiring complete with 1.5 sqmm single-core PVC insulated but unsheathed multistranded copper conductor FRLS cable 650/1100 Volts grade drawn through and including non-metallic rigid PVC heavy duty concealed conduit (minimum 20 mm dia external) |
| 41 | Supply and fixing of One Socket outlet three pin, 6 Amp, on the same board, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, all as specified. |
| 42 | Supply and fixing of one Socket outlet three pin, 6 Amp, independent, with 1.5 Sq. mm (nominal area) cable & 1.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non-metallic PVC medium duty concealed conduit all as specified. |
| 43 | Supply and fixing of One socket outlet three pin, 5&15 Amp, independent, with 2.5 Sq. mm (nominal area) cable & 2.5 Sq. mm (nominal area) cable as earth continuity conductor, in and including rigid non-metallic PVC medium duty concealed conduit all as specified. |
| 44 | Supply and fixing of Switch modular type single pole, one way, 6 Amp, one module, complete all as specified. |
| 45 | Supply and fixing of Switch modular type single pole one way, 16 Amp, one module, complete all as specified. |
| 46 | Supply and fixing of Socket outlet modular type, multipurpose, 2/3 pin, single pole one way, 6 Amp, two module, complete all as specified. |
| 47 | Supply and fixing of Socket outlet modular type multipurpose 2/3 pin single pole one way, 6/16 Amp, two module, complete all as specified. |
| 48 | Material and labor for Modular ceiling rose, 3-Phase / PVC / polycarbonate, isolated body complete all as specified and directed. |
| 49 | Supply and fixing of in replacement of MCB DB 4way sheet enclosure double door type, single pole and neutral 240V with standard bus bar of suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete without MCB and with enclosure blank plates for unused way suitable for 12 way type, complete all as specified and directed by Engr-in-Charge. Note: GI boxes, DBs, and other wall-mounted enclosures shall be fixed flush with the finished wall surfaces in the designated positions using cement mortar of 1:4 mix ratio, |
| 50 | Supply and fix in replacement MCB of 6-32 Amp SP, 240 volt 'C' series, 10 KA rating complete all as specified and directed by Engr-in-Charge. Make Legrand/Siemens/L&T. |
| 51 | Supply and fix in replacement MCB of 32 Amp SPN, 240 volt 'C' series, 10 KA rating complete all as specified and directed by Engr-in-Charge. Make Legrand/Siemens/L&T. |
| 52 | Supply and fixing of submain wiring 2 x 4.0 Sqmm + 1 x 4.0 Sqmm earth wire using ISI marked 1.1 kV grade single core FRLS flexible cable, conforming to IS: 694-1990, having multi-drawn thin strands of electrolytic copper conductors and insulation conforming to IS: 5831-1984, type C, HR 85°C + FR for phase, neutral and earth continuity conductor connecting to earth dolly, drawn in not less than 25 mm size in existing conduits / PVC Casing capping surface/recessed conforming to IS: 9537 Part-3, colour-coded as specified in IS: 732-1989, including making good of disturbed surfaces of wall/ceiling/floor with painting, all complete as specified and directed. NOTE: 01 run of phase conductor, 01 run of neutral conductor, 01 run of earth continuity conductor and 01 run of PVC Casing capping shall be measured as one length. |
| 53 | Supply and fixing of wall mounted rechargeable invertor LED batten 20(±10%) watt, 6500K, 4ft, not less than 4 hours backup, efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor and inbuilt driver & lithium battery complete including making connection complete all as specified and directed. Make-Havells Cat Part no- LHEXACP7FN1W020 or Equivalent in Phillips/Bajaj. |
| 54 | Supply and fixing of in Replacement of u/s LED building security light of capacity 35 watt, LM6 high pressure die cast aluminium housing, IP 66 protection , THD<20%, PF>0.95, Operating Voltage 140-270V AC, 50Hz, complete all as specified and directed by Engr-in-Charge. |
| 55 | Supply and fix exhaust fan, steel body AC Single Phase, 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-Charge. |
| 56 | Supplying and fixing lamp holder, PVC/Polycarbonate type with back plate suitable for batten fitting including connections etc. as required. |
| 57 | Supply and fixing of Led Bulb, 10 W 230 V AC 50 Hz complete all as specified and directed. |
| 58 | Supply and fixing post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete set all as specified and directed by Engr-in-charge |
| 59 | Supply, laying & testing PVC insulated, PVC sheathed cable electric control cables (Heavy duty) with stranded copper conductor of size 1.5 sq mm, 3 core, 1100 Volts grade all as specified and directed by Engr-in-Charge. |
| 60 | Supply and fixing Rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.all as specified and directed by Engr-in-Charge. |
| 61 | Supply and fixing thermoplastic cable junction box for lights of size 205 x 255 x 112mm including bus bar/terminal for cable connection with IP-66 protection complete all as specified and directed by Engr-in-Charge. |
| 62 | Material and labor for MCB SP 240 volt C curve 10 KA, ISI marked as per IS/IEC 60898-1 2002 of 6/32 Amps capacity IP 20 complete all as specified and directed by Engr-in-Charge. |
| 63 | Supply and fixing stainless steel pipe 60mm bore for Post top light complete all as specified and directed by Engr-in-Charge. |
| 64 | Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 in depth and getting out in soft soil for taking up or laying of cable/erecting of pole/stay complete all as specified and directed. |
| 65 | Returning filling in including spreading levelling watering and well ramming in layers not exc. 25 cm thick each complete all as specified and directed. |
| 66 | Removing excavated material to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point of any type of soil complete all as specified and directed. |
| 67 | Supply and fixing Facade light 15 W 240 V IP 65 Warm white outdoor complete all as specified and directed by Engr-in-charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysNov 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender