Tender For Special Repairs To Shutters In 19 Ad Regt Under Ge (I) Gos
Tender Value
Ref. Documents
Estimated cost
Bid Submission
13 Nov 2026
19 days left
EMD
95000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ganjam → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repairs To Shutters In 19 Ad Regt Under Ge (I) Gos
BOQ
| Sl. No. | Item Description |
| 1 | List of works |
| 2 | Taking down rolling shutters of any size including all hardware fittings complete all as specified & directed by Engineer-In-Charge |
| 3 | M&L Cutting holes in brick walls built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified & directed by Engineer-In-Charge |
| 4 | S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified & directed by Engineer-In-Charge |
| 5 | S&F in repair MS pipe 50 to 125 mm dia as shaft including two coats of aluminum paint over a coat red oxide primer complete all as specifed & directed. |
| 6 | S&F in repair part of steel rolling shutters MS gear box set general complete incl handle and anchoring rod as of approved quality all as specified and directed. |
| 7 | S&F in repair Ball bearing suitable for rolling shutter complete all as specified and directed. |
| 8 | S&F in repair Guide channel 3\\" (3.50 mm thick) mild steel deep channel section etc.complete all as specified and directed. |
| 9 | S&F in repair Hood Cover made of 1 mm thick GI Sheet pattern |
| 10 | S&F in repair Bottom plate 5\\" (2.25mm) complete all as specified and directed. |
| 11 | S&F in repair Anchoring rod of 25 mm dia of MS pipe complete all as specified and directed. |
| 12 | S&F in repair Safety lever locks MS with 4 levers complete all as specified and directed. |
| 13 | Taking down and refixing in the same opening steel rolling shutter including oiling and greasing to required necessary fitting to functionall shutters as required bush, Spring. MS pipe , rod .lock. ball bearing, top cover, anchoring rod, hasp and staple and push pull or gear operating system , bevel gear box and crank handle etc complete all as specified.and directed.(area of rolling shutters exc 6 sqm but n. exc. 18 Sqm each )(Note:- Necessary constituent items required during repair of rolling shutter shall be paid seperately as given above .) |
| 14 | S & F in repair Complete rolling shutter including 1.00 mm thick mild steel rolling shutter strips duly pressed on both ends of vertical sides for interlocking locks for the required length of existing steel rolling shutter including oiling and greasing to required necessary fitting to functionall shutters as required bush, Spring. MS pipe , rod .lock. ball bearing, top cover, anchoring rod, hasp and staple and push pull or gear operating system , bevel gear box and crank handle etc complete all as specified.and directed. as directed by Engg-in-Charge |
| 15 | S & F in repair 1.00 mm thick mild steel rolling shutter strips duly pressed on both ends of vertical sides for interlocking locks for the required length of existing steel rolling shutter complete all as specified.and directed. as directed by Engg-in-Charge |
| 16 | M&L for preparation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth and apply two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 17 | M&L preparation of old decorated Steel painted surfaces of any description not other wise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge |
| 18 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 19 | Demolition of brick work built in cement mortar including all quions, arches, pillars etc all as specified and directed |
| 20 | M & L for old size brick work with fly ash bricks straight or curved on plan exc 6m mean radius in CM 1:6 completed all as specified and directed. |
| 21 | M&L for rendering 10 mm thick on other than fair face of brick works in CM 1:6 and to be finished even and smooth with out using extra cement complete all as specified and directed. |
| 22 | M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed. |
| 23 | M&L for preparation of new decorated surfaces of walls and apply one coat of white wash complete all as specified and directed |
| 24 | M&L for preparation of new plastered surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed. |
| 25 | Preparation of Newly Plastered surfaces and applying two coat of Cement Base Paint on walls all as specified and directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysNov 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender