Tender For Supply Of 2 Nos. 7.5 H.P Submersible Monoblock Pump Motor Set In The New Under Ground Reservoir (U.G.R.) And Some Allied electrical installation Work At Lig Sodepur Under Sodepur Electrical Section Under Electrical Division-Ii, Housing Dir
Tender Value
Ref. Documents
Estimated cost
Bid Submission
30 Oct 2026
4 days left
EMD
8038
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
24 Paraganas North → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Supply Of 2 Nos. 7.5 H.P Submersible Monoblock Pump Motor Set In The New Under Ground Reservoir (U.G.R.) And Some Allied electrical installation Work At Lig Sodepur Under Sodepur Electrical Section Under Electrical Division-Ii, Housing Directorate.
BOQ
| Sl. No. | Item Description |
| 1 | Supply & delivery of 440 Volt, 3 Phases, 7.5 H.P Submersible Monoblock Pump motor, RPM 3000 set (make Kirloskar Brothers Ltd. Model No. KOS 844+ Suc+ Dev 65 X 65 Head 40 mtr.) incl. all accessories. |
| 2 | Installation 7.5 HP Submersible Monoblock Pump set with necessary special type tools & tackles incl chain pully, tripod stand in the underground reservoir as per direction of EIC |
| 3 | Charges for making flat cable jointing |
| 4 | Supplying, fitting and fixing of PP Header Assemblies ofapproved make andquality, all complete as per direction of Engineer in -charge. ----- Header Asly-3\\" with PVC Ball valve & Port for 1& 2 \\" Ventury |
| 5 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required 80 mm dia |
| 6 | Supply & fixing of G.I. plain equal elbow of approved brand and make ISI ---- 80 mm dia |
| 7 | 65 mm dia |
| 8 | 50 mm dia |
| 9 | Supply & fixing of G.I. short piece of TATA make (Above 50mm & upto 150 mm long) --- 65 mm dia |
| 10 | 80 mm dia |
| 11 | Supply of G.I. reducing socket with I.S.I. mark. --- 65 mm |
| 12 | Supplying, fitting and fixing of CI Non Return Valve as per IS:5312 ----- C. I. NON RETURN VALVE 3\\" |
| 13 | Cutting holes and subsequent mending good damages ---- Diameter upto 150 mm --- In brick work [Cement-4.0 Kg/Mtr] |
| 14 | Supply and fixing of G.I. union ----- 50mm |
| 15 | Supplying, fitting & fixing bolts with nuts & washers ---- (i) 10 to 16 mm dia. -- Length upto 75 mm |
| 16 | Supplying, fitting and fixing of G.M. Gate Valve as per IS:778. -- G. M. Valve 3\\" |
| 17 | Supply of GI flange --- 80 mm dia (Make - HB) |
| 18 | Supply and fixing of G.I. plain tee of approved brand and make ISI 80 mm dia |
| 19 | S/F of Heavy type holding clamp for holding 32 mm dia column pipe with pump motor set at an average depth of 80 - 100mtr. |
| 20 | S/F of 1200 mm dia M.S well cover with suitable size of hole for entering 50 mm dia column pipe and 25 mm dia cable protection pipe inside the tube well. |
| 21 | S & F 80 mm. dia. rubber gasket for flange. |
| 22 | S/F 2.5 sq mm Flat Submersssible PVC insulated Cu 3 core cable of (Make - Finolex/Havells/KEI/Glostar) |
| 23 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required 50 mm dia |
| 24 | Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required 40 mm dia |
| 25 | Supply & Installation of M.S. fabricated O.D. type feeder pillar box having overall dimention of 1200 mm x 900 mm x 450 mm . the body & upper portion of the pillar box made of 5 mm thick M.S. Shet & bottom portion with 5 mm. thick M.S. Plate rigidly fixed by nuts, bolts & washer etc. with 50 mmx 50 mm x 6 mm M.S. Angle & 25 mm x 6 mm M.S. Flat. The pillar box having both sides opening with suitable handle in each door with double locking arrangement is to be provided with Godrej Almirah type lock with 3 nos. key. additional provision for pad locking & supply of Godrej Navtal duplicate key lock is also to be provided mechanical locks with top & bottom. Provision for ventilation grill should be rectangular shape made of M.S. Plate duly welded to lateral sice. The central ventilation spout at starting surface of the top pillar box. Provision for 2 nos. earthing terminal 25x6 mm G.I. Flat having suitable nuts, bolts, washer for connecting the accessories. Necessary interconnection between incoming & outgoing surface by suitable size Cu. Flat/wire duly sleeved & insulated. Finishing the end by socketing & providing glands as required. The pillar boxboth inside & outside is to be painted with two coats of Aluminium paint over one coat of red lead primer & M.S/ISMC. Channel of size 75 mm x 40 mm x 4.9MM with nuts & bolts at bottom portion with two coats of black annealed paint after finishing the surface properly. The internal E.I. works of pillar box should be suitable to withstand 2 KV. for one minute. The all fabrication work should be done as per direction of E.I.C. The pillar box comprising with the following:- Incoming - a) Supplying and fixing 63 Amp 240/415 V FPMCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection with enclousure----1 no Outgoing - b1) Supplying and fixing 32 Amp 240/415 V DPMCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection with enclousure---3 nos., b2)Supplying and fixing changeover switch with sheet steel enclosure on angle iron frame on wall with nuts bolts etc. 63A----1no. , Busbar c) S & F 500volt, 100 Amp. Capacity of sizr 15 x 3 mm. 4 nos. copper bar of required size porcelain chairs incl. Hylum sheet behind copper bar. Accessories - d) S & F C.T. coil (100/5 Amp.) A.E/Kappa make ……… 3 nos., e) S & F three phase panel mounted Digital Voltmeter (0-500 Volt) in 96 x 96 sq.mm. flush mounted case (make l&t WL132010OOOO ,).1 set., f) S & F three phase panel mounted Digital Ammeters in 96 x 96 sq.mm. flush mounted case (make l&t WL131010OOOO..1 set., g) S & F indicating lamp (LED) (approve make) ………….3 set., h) S & F 6 Amp SPMCB for indicating lamp(approved make) -- 3 set., i) S & F MU-G15 Starter ( LT make, Cat No. CS94091SOCO) relay range (11--18 A) 2 set., j) S & F E.I. Danger board 15 cm x 10 cm (6\\"x4\\")------1 no., k) supply and fixing 240DP MCB of 10kA&C characteristics. , l) Godrej Navtal 7 Liver Locxk with Key ………… 1 no., m) Interconnection with 6 sqmm & 1.5 sq. mm pvc insulated unsheathed stranded copper wire as required …. k)Supplying & Fixing bulk head light fitting (Havells make) with die cast aluminium housing & frosted glass on wall/ceiling incl. S&F 8watt CFL / 100 watts GLS lamp complete set incl S/F 5 A piano switch on 100 mm x 100 mm x 65 mm MS Box incl cover & connection as to GS |
| 26 | Supplying and Drawing 1.1 KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required ---- 2 x 22/0.3 (1.5 sqmm) -- for interconnection |
| 27 | Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. --- 1.5 sqmm |
| 28 | 2.5 sqmm |
| 29 | Supply & Fixing EI danger board on wall ----- 20 cm x 30 cm (8\\"x12\\") |
| 30 | Supply & Delivery 1.1 kv gr. 4 core X 25 sq.mm. XLPE Al. armoured cable as per direction of EIC |
| 31 | Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed |
| 32 | Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish ---- From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor/pavement/wall etc |
| 33 | Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below : For 4 core x 25 sqmm |
| 34 | Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials : 4 core 25 sqmm cable |
| 35 | Excavation of soil for installation of Earth Electrode and filling & ramming. ---- For Soft Soil |
| 36 | Earthing with 65 mm dia GI pipe (TATA-Medium)x 3.0 Mts. long and 1 x 19/10 stranded GI (Hot Dip) wire (4 Mts. long), 20 mm dia x 125 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above groundlevel to an average depth of 3.65 Mts |
| 37 | Supplying and fixing415V, TPNSFU with sheet steel enclosure on flat iron/angle iron frame on wall with nuts bolts etc. incl.S&F3nos.DIN type HRC fuse as per rating.-- Angle iron frame – 100A – (Make – L&T/Legrand/Siemens) |
| 38 | Supplying & fixing sheet metal (16SWG) Iron Clad Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required–( As per Drawing no. 470 of PW Specification Book – May 1991)--- Dimension of Cu. bars [85mm long] - 4 x 15x3mm, 415 V, 100/125 A, Dimension of Sheet Metal Box - 500x150mm |
| 39 | Supplying and fixing240/415VMCB of Breaking capacity10kA & C characteristics on din rail of existing DBs and necessary connection – 63A (Make – Legrand/Semines/Schinders) & Supplying and fixing MCB SS enclosure withIP-20/30 protection, powder coated provision for two/four pole MCB, concealed in wall after cutting the wall &mending good the damages to original finish incl. painting, connection & provision for earthing attachment—4way |
| 40 | Supplying and fixing240/415VMCB of Breaking capacity10kA & C characteristics on din rail of existing DBs and necessary connection – 40A (Make – Legrand/Semines/Schinders) & Supplying and fixing MCB SS enclosure withIP-20/30 protection, powder coated provision for two/four pole MCB, concealed in wall after cutting the wall &mending good the damages to original finish incl. painting, connection & provision for earthing attachment—2way |
| 41 | Supplying and Drawing 1.1KV single core stranded 'FR' PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC)of the following sizes in the prelaid polythene pipe and by the prelaid GI finish wire and making necy. connection as required—4x80/0.4 (10 sqmm) + 2x84/0.3 (6 sqmm) as ECC necy. Connection as requires from 100A busbar of different meter (2mtr x 09nos.) as to 18 mtrs x 29 nos block |
| 42 | Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal/Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 43 | Finishing of the PVC insulated wire ends by socketting with pin/ ring type copper sockets and insulated tapes etc., including supplying sockets, tapes. --- 10 sqmm |
| 44 | 6 sqmm |
| 45 | (Rate should be quoted including all updated taxes and duties GST, LWC from Sl. no. 1 to 39.1) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender