Tender For Repair And Maintenance Of Of Ts Barrack At Communication Complex Of 154 Bn Bsf Ambassa Under Shq Bsf Telimura.
Tender Value
10.49 Lakhs
Estimated cost
Bid Submission
30 Oct 2026
4 days left
EMD
20999
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Khowai → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Of Ts Barrack At Communication Complex Of 154 Bn Bsf Ambassa Under Shq Bsf Telimura.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :-1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :-1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:-Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 5 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 6 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.-0.63 mm thick with zinc coating not less than 275 gm/ m² |
| 7 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.-0.63 mm thick with zinc coating not less than 275 gm/m² |
| 8 | Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).-6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 : 2000 |
| 9 | 12 mm cement plaster finished with a floating coat of neat cement of mix :-1:4 (1 cement: 4 fine sand) |
| 10 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :-Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 11 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 12 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour -Old work (one or more coats) |
| 13 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :-One or more coats on old work |
| 15 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.-With cement mortar 1:4 (1 cement : 4 fine sand) |
| 16 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:-G.S. Sheet |
| 17 | Modified Estimated Cost after using Correction factor on DSR 2023 on acount of GST @ 0.973 |
| 18 | Add Cost Index @ 60% on DSR 2023 |
| 19 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Group A |
| 20 | Wiring for light/ power plug with 2X4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No. 4 sq. mm FRLS/HFFR PVC insulated copper conductor single core cable for loop earthing as required. |
| 21 | Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (i) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 22 | (ii) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 23 | Supplying and drawing following siizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel PVC conduit as required.(i) 3 x 1.5 sq. mm |
| 24 | Supplying and drawing following pair 0.5 mm dia FRLS/HFFR PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 25 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(i) 20 mm |
| 26 | (ii) 25 mm |
| 27 | Supplying and fixing following modular type switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.(i) 5/6 Amp. Switch |
| 28 | (ii)15/16 A switch |
| 29 | (iii) 3 pin 5/6 A socket outlet |
| 30 | (iv) 6 pin 15/16 A socket outlet |
| 31 | (v) Telephone socket outlet |
| 32 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 33 | Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm) |
| 34 | 4 Module (125mmX75mm) |
| 35 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. |
| 36 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 37 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. |
| 38 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch,connections etc. as required. (For light plugs tobe used in non residential buildings) |
| 39 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. |
| 40 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)(i) 12 way, Double door |
| 41 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required(i) Single pole |
| 42 | (ii) double pole |
| 43 | Earthing with G.I.earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 mtrs long etc. with charcoal or coke and salt complete as required. |
| 44 | Providing and fixing 6 SWG dia G.I. Wire in 15 mm dia GI pipe from earth electrode i/c connection with GI nut bolt spring washer exacavation and refilling etc as required. |
| 45 | Supplying and fixing Brush Less Direct Current (BLDC) Fan without Remote Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 °C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. |
| 46 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 47 | Supplying, installation, testing & commissioning of following pre-wired ,LED type street light fittings, complete with all accessories, and 32 mm dia(nominal) 'B' class GI pipe bracket, reduser for mounting fitting on wall including bending the pipe to the required shape, and connections with 3 x 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. a) 45W LED Street light luminaire with power LEDs. (Acceptable makes: CG make Model- Havells ENDURASUNDOWNSL45WLED765PASYBOTG or equivalent to Havells/philips/crompton |
| 48 | Providing and fixing 09 watt self ballasted LED retrofit (fitted in normal Lamp holder) bulbs with PBT body shell and PC diffuser.BC 6500K etc.as reqd. make Polycab/Havell/Phillips/Crompton. |
| 49 | Providing and fixing of 20 watt ,6500 k LED Decorative ultra slim square profile LED lighting fixture with extruded Polycarbonate environmental friendly , energy efficientb ready to use pack directly on ceillng /wall, including round sheet ,connection ,testing and dismantling the existing comlete etc as required. Make- Havells/CG/Phillips/Syska |
| 50 | Supplying & laying of one number XLPE insulated and PVC sheathed , armoured aluminium power cable of 1.1 KV Grade of size 2X16 Sq. MM conf to IS: 7098 (Part-I) in the existing METAL/HDPE PIPE / IN OPEN as required. |
| 51 | Supplying and Laying of one no PVC insulated/PVC sheathed XLPE power cable ,1.1 KV grade (heavy duty), armoured UG electric cable with aluminium conductor of size 2 x 16 sqmm direct in ground including excavation and refilling the trench but excluding sand cushioning & protective covering (make Havells / Polycab / Finolex / Gloster.) |
| 52 | Supplying and fixing G. I. pipe of 40 mm dia (Medium duty) along the wall / surface for protection of UG cable / lightening conductor etc as required. |
| 53 | Supplying and fixing of 300 mm sweep,( light Duty) exhaust fan suitable for single phase, 50 HZ, 230 v, AC supply in existing opening inlcluding making the hole to suit the size of above exhaust fan & S/F of louver/ Shutter including connection, testing etc. as required of Bajaj, Crompton etc. |
| 54 | Total Cost (BoQ1+BoQ2) |
| 55 | Civil work |
| 56 | Elect work Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysNov 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender