Tender For Repair And Maintenance Of Diesel Generating Sets, Amf Panels, Fire Fighting And Fire Alarm System At installation Valsura Jamnagar
Tender Value
44 Lakhs
Estimated cost
Bid Submission
14 Nov 2026
14 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jamnagar → Gujarat
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair And Maintenance Of Diesel Generating Sets, Amf Panels, Fire Fighting And Fire Alarm System At installation Valsura Jamnagar
BOQ
| Sl. No. | Item Description |
| 1 | M&L for attending 'B' check of DG set of capacity 63 kVA (Make : Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as ordered including testing on completion of the following complete all as directed:-(i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel leakage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, Repair if required. (vi) Check electrical connections of engine. The wiring shall be maintained properly and engine starting system from engine instrument panel shall be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging Repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning. (xii) Change of Air filter element with ‘O’ ring. (xiii) Change of filter insert with ‘O’ ring (xiv) Change of Lubricating oil filter. (xv) Change of Primary filter element. (xvi) Change of secondary filter element. (xvii) Change of greaves Lub oil CI4- 10 ltrs pack (xviii) Change of Radiator pre-mix greaves KOOL 10 ltrs, complete to the satisfaction of Engineer -in-charge. Notes :- (i) Unit rate quoted by the tenderer shall be deemed to include for minor spares/extras required for replacement to make the DG set fully functional. The decision of Accepting officer regarding minor spares/ extras shall be final, conclusive and binding. (ii) All T&P shall be arranged by contractor and rates for the same shall deemed to be included in rate quoted. |
| 2 | All as per serial item No. 1 here-in-above, but DG set of capacity 100 kVA Make: Greaves |
| 3 | All as per serial item No. 1 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20 Ltrs pack complete for DG set of capacity 160 kVA Make: Greaves |
| 4 | All as per serial item No. 1 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20 Ltrs pack complete for DG set of capacity 250 kVA Make: Greaves |
| 5 | All as per serial item No. 1 here-in-above, but twice during the contract period and change of greaves Lub oil CI4- 20 Ltrs pack complete for DG set of capacity 125 kVA Make: Greaves Power |
| 6 | All as per serial item No. 1 here-in-above, but once during the contract period and change of Cummins Lub oil CI4- 20 Ltrs pack complete for DG set of capacity 160 kVA Make: Jakson |
| 7 | M&L for attending 'B' check for DG set of capacity 15 kVA (Make: Kirloskar) at different locations to carry out maintenance/ servicing as given below once during the contract period as & when ordered including testing on completion of the following complete all as directed :-(i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc.(ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel leakage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/ silencer, repair if required. (vi) Check electrical connections of engine. The wiring shall be maintained properly and engine starting system from engine instrument panel shall be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging, repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Spinon Lub oil filter (xiii) Change of air cleaner element (xiv) change of Belt- AVX 10 1500 (xv) Change of fuel filter element (xvi) Change of KOEL care premium genuine oil 7.5 Ltrs , complete all as specified and directed by Engineer-in-charge. Notes :- (i) Unit rate quoted by the tenderer shall be deemed to include for minor spares/extras required for replacement to make the DG set fully functional. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding. (ii) All T&P shall be arranged by contractor and rates for the same shall deemed to be included in rate quoted. |
| 8 | All as per serial item No. 7 here-in-above, but change of V Belt cogged- AVX10 1265L blower pulley, Change of V Belt cogged-AVX10 1136 for alternator pulley and Change of KOEL care premium genuine oil 13 Ltrs Can, complete for DG set of capacity 40 kVA Make: Kirloskar |
| 9 | All as per serial item No. 7 here-in-above, but change of V Belt cogged- AVX SERIES blower pulley, Change of V Belt cogged-AVX for alternator pulley and Change of KOEL care premium genuine oil 40 Ltrs Can, complete for DG set of capacity 380 kVA Make: Kirloskar |
| 10 | M&L for attending 'C' check of DG set of capacity 63 kVA (Make : Greaves) at different locations to carry out maintenance/servicing as given below once during the contract period as & when ordered including testing on completion of the following complete all as directed: (i) Check and clean engine, alternator battery, instrument panel, AMF panel, Timer, Contactors, Meters and others etc. (ii) Tightening of all nuts & bolts of DG set and its accessories. (iii) Check for any diesel leakage from any point and rectify if observed. (iv) Check and adjust fan belt tension, replace the fan belts if found damaged. (v) Check leakage of smoke from exhaust system/silencer, repair if required. (vi) Check electrical connections of engine. The wiring shall be maintained properly and engine starting system from engine instrument panel shall be kept in order. (vii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged. (viii) Check exhaust pipe, flange and lagging, repair if found damaged. (ix) Check output of alternator, if found OK adjust the same to specified values in case of brush type. (x) Checking of all hoses and cleanup, if required. (xi) Oiling, Greasing and checking for proper & smooth functioning (xii) Change of Gasket set 4G11TA (w/o Head gasket) (xiii) Change of cogged belt AX43-1143L (xiv) change of pipe turbo oil supply (xv) Change of pipe turbo drain (xvi) Change of set of hoses for 4G valve (xvii) Change of setting screw (xviii) Change of hex nut M8x1 DIN934 (xix) Change of gasket for PDC rocker cover (xx) Change of set of flex F/P (xxi) Change of push rod. Notes :- (i) Unit rate quoted by the tenderer shall be deemed to include for minor spares/extras required for replacement to make the DG set fully functional. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding. (ii) All T&P shall be arranged by contractor and rates for the same shall deemed to be included in rate quoted. |
| 11 | All as per serial item No. 10 here-in-above, but DG set of capacity 100 kVA Make: Greaves |
| 12 | All as per serial item No. 10 here-in-above, but DG set of capacity 160 kVA Make: Greaves |
| 13 | All as per serial item No. 10 here-in-above, but for DG set of capacity 15 kVA Make: Greaves |
| 14 | All as per serial item No. 10 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar |
| 15 | S&F in repairs set of hoses with clips for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 16 | S&F in repairs set of fuel pipes for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 17 | S&F in repairs set of injector pipes for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 18 | S&F in repairs Exhaust silencer for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 19 | S&F in repairs injector with nozzle for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 20 | M&L for greaves lubricating oil SAE 15W40 suitable for DG Set. |
| 21 | M&L for Coolant suitable for DG sets. Make: Fleetguard, Valvoline, Premium |
| 22 | S&F in repairs Air filter outer for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 23 | S&F in repairs Air filter inner for DG set of capacity 63/ 100/ 125 kVA Make: Greaves |
| 24 | S&F in repairs 12V temperature gauge (40-120 deg cel) for DG set of capacity 63/ 100 kVA Make: Greaves |
| 25 | S&F in repairs 12V pressure gauge, 0-10 bar for DG set of capacity 63/ 100 kVA Make: Greaves |
| 26 | Servicing and calibration of FIP (Fuel injection pump) & nozzles including replacement of minor parts like nuts, bolts, washers, etc of DG Set 63/100 KVA capacity. |
| 27 | M&L for taking out Radiator of DG set 63 kVA/100 kVA (Make: Greaves) for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed. |
| 28 | M&L for taking out Radiator of DG set 160 kVA/250 kVA (Make: Greaves/ Cummins/ Jackson) for repair, welding, brazing, leak testing & refixing to DG set to its original position and testing complete all as directed. |
| 29 | Servicing & repair to self starter of DG set of capacity 15/40 kVA (Make: Kirloskar) including replacement of parts such as washer, nut, bolts, bush, solenoid, rotor etc. assembling and testing complete. |
| 30 | All as per serial item No. 29 here-in-above, but for DG set of capacity 63/100 kVA Make: Greaves |
| 31 | All as per serial item No. 29 here-in-above, but for DG set of capacity 160/250 kVA Make: Greaves/ Cummins/ Jackson |
| 32 | S&F in repair Solenoid Switch for 15/ 40 kVA DG set (Make: Kirlosakar) and testing complete for proper functioning. |
| 33 | S&F in repair Solenoid Switch for 63/ 100/ 160 kVA DG set (Make: Greaves/ Cummins) and testing complete for proper functioning. |
| 34 | S&F in repair Relay card for 15/ 40 kVA DG set (Make: Kirlosakar) and testing complete for proper functioning. |
| 35 | S&F in repair Relay card for 63/ 100 kVA DG set (Make: Greaves) and testing complete for proper functioning. |
| 36 | S&F in repair Solenoid Switch for 160/250 kVA DG set (Make: Greaves/ Cummins) and testing complete for proper functioning. |
| 37 | S&F in repair AVR suitable for 15 kVA DG Set complete all as directed. |
| 38 | S&F in repair AVR suitable for 40 KVA DG Set complete all as directed. |
| 39 | S&F in repair AVR suitable for 63 KVA DG Set complete all as directed. |
| 40 | S&F in repair AVR suitable for 100 KVA DG Set complete all as directed. |
| 41 | S&F in repair AVR suitable for 160 KVA DG Set complete all as directed. |
| 42 | S&F in repair AVR suitable for 250 KVA DG Set complete all as directed. |
| 43 | S&F in repair battery auto cable copper PVC insulated unsheathed 35 Sqmm single core copper cable complete all as specified and as directed. |
| 44 | S&F in repair battery auto cable copper PVC insulated unsheathed 95 sqmm single core copper cable complete all as specified and as directed. |
| 45 | S&F 90AH 12Volt Lead acid battery (Maintenance free battery with minimum 2 years manufacturer’s warranty) for DG set. Make: Exide Xpress or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 46 | S&F 150AH 12Volt Lead acid battery (Maintenance free battery with minimum 2 years manufacturer’s warranty) for DG set. Make: Exide Gold or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 47 | S&F copper battery lugs for DG set battery complete all as directed. |
| 48 | S&F in repair Ignition Switch of DG Sets complete all as directed. |
| 49 | S&F in repair No volt coil for contactor of capacity up to 200 Amp Capacity all as specified and as directed. Make : L&T /C&S/Schneider or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 50 | S&F in repair LED type pilot lamp. |
| 51 | S&F in repair selector switch in existing panel complete all as directed. |
| 52 | S&F in repair Volt meter 0-500 Volt in existing panel including wiring from bus bar to volt meter terminals and fix the wiring with existing control wiring complete all as directed.Make: L&T/ Meco/ HPL or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 53 | S&F in repair Ammeter 0-100 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring complete all as directed.Make: L&T/ Meco/ HPL or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 54 | S&F in repair Ammeter 0-200 Amp in existing panel with necessary wiring from CT to Ammeter and fix the wiring in existing set of control wiring complete all as directed.Make: L&T/ Meco/ HPL or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 55 | S&F in repair electronic timer of 215/240/360/415 Volt 3 to 120 Sec complete all as directed. Make: L&T/C&S/Schneider or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 56 | M&L for wiring loom of control panel of DG Set AMF panel from Relay and auxiliary contacts complete by using 2.5 sq.mm copper cable of colour code from auxiliary contacts to Relay including fault finding etc complete all as specified and as directed. |
| 57 | M&L for Overhauling of water pump with repairing kit for 63/100 kVA DG set complete all as directed. |
| 58 | M&L for Overhauling of water pump with repairing kit for 160/250 kVA DG set complete all as directed. |
| 59 | M&L for complete checking of AMF panel, finding the fault, servicing complete including replacement of unserviceable spares and testing complete for manual & Auto operations all as directed. Note: Supply only of new items required for replacement shall be measured & paid for separately under respective items of this Schedule. |
| 60 | Supply only AMF Relay. |
| 61 | Supply only single phase preventer. |
| 62 | Supply only PLA relay. |
| 63 | Supply only 3 pole power Contactor 70 A, 415 V. Make: L&T ‘ML-4’ or equivalent in makes mentioned in Appendix 'B' here-in-after. |
| 64 | Supply only 3 pole power Contactor 163 A, 415 V. Make: L&T ‘ML-4’ |
| 65 | S&F in repair HRC Fuse base of capacity 200 Amps. |
| 66 | S&F in repair Anti vibration pad set suitable for 63/ 100kVA DG set all as directed. |
| 67 | M&L for taking out alternator of DG set of capacity 15 kVA (Make: Kirloskar) by dismantling from engine pulley including disconnecting electrical connection complete & transporting to workshop. Opening the rotor and stator for rewinding with copper wire of existing guage and then varnishing the stator & rotor with good quality varnish, Heating and baking complete upto requisite duration. Check bearing & shaft for machining if required. Re-assemble stator & rotor by replacing existing bearings with new bearings complete. Back transportation alternator to base and coupled with engine by using new rubber bushing spider, nut bolts complete. Testing the system for smooth functioning & checking current and load output by giving existing electrical load to the entire satisfaction of Engineer-in-charge. |
| 68 | All as per serial item No. 67 here-in-above, but for DG set of capacity 40 kVA Make: Kirloskar |
| 69 | All as per serial item No. 67 here-in-above, but for DG set of capacity 63 kVA Make: Greaves |
| 70 | All as per serial item No. 67 here-in-above, but for DG set of capacity 100 kVA Make: Greaves |
| 71 | All as per serial item No. 67 here-in-above, but for DG set of capacity 160 kVA Make: Greaves/ Jackson |
| 72 | M&L for Readymade electrolyte having specific gravity 1.4 for DG set of any capacity all as directed. |
| 73 | M&L for Distilled water having specific gravity 1.0 for DG set of any capacity all as directed. |
| 74 | S&F in repair MCCB with thermal magnetic protection unit rating 160 Amp, 4 Pole, 25 kA, 415 Volt grade, AC, 50 Hz, adjustable Thermal - Magnetic release type in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items and taking down old item complete all as specified. Make: Legrand Cat Part No. 4200 57. |
| 75 | S&F in repair MCCB with thermal magnetic protection unit rating 100 Amp, 4 Pole, 25 kA, 415 Volt grade, AC, 50 Hz, adjustable Thermal - Magnetic release type in existing panel boards connecting with proper size link set at incoming and outgoing cable end with cable connections and including necessary addition / alteration to existing panel with welding cutting to steel structure and providing new steel items and taking down old item complete all as specified. Make: Legrand Cat Part No. 4200 55. |
| 76 | S&F in repair AMF Panel, outdoor type, double door factory facricated 3mm thick CRCA sheet front opening with aluminium bus bar switch gear and all requisite internal fittings/ fixtures suitable for 100 kVA DG Set, 3 Phase, 50 Hz, 1500 RPM with 250 Amp MCCB incomer of Make: Greaves (Engine Sl No. 13080480061, Alternator Sl No. 8K319) complete all as specified & as directed by Engineer-in-Charge. |
| 77 | S&F in repair AMF Panel, outdoor type, double door factory facricated 3mm thick CRCA sheet front opening with aluminium bus bar switch gear and all requisite internal fittings/ fixtures suitable for 63 kVA DG Set, 3 Phase, 50 Hz, 1500 RPM with 250 Amp MCCB incomer of Make: Greaves (Engine Sl No. 13080480400, Alternator Sl No. 08H22734) complete all as specified & as directed by Engineer-in-Charge. |
| 78 | S&F in repair AMF Panel, outdoor type, double door factory facricated 3mm thick CRCA sheet front opening with aluminium bus bar switch gear and all requisite internal fittings/ fixtures suitable for 100 kVA DG Set, 3 Phase, 50 Hz, 1500 RPM with 400 Amp MCCB incomer of Make: Greaves (Engine Sl No. 13080480057, Alternator Sl No. 81931339) complete all as specified & as directed by Engineer-in-Charge. |
| 79 | M&L for preparing old painted surface by scraping with requisite tools of DG Set 160 kVA and applying two coats of 1st quality synthetic enamel paint as per existing colour by spray gun or by brush as applicable, over & inclduing primer coat of red oxide and including writing the SM No. / MES No. on DG Set in two inch block letter with synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 80 | M&L for preparing old painted surface by scraping with requisite tools of DG Set 100 kVA and applying two coats of 1st quality synthetic enamel paint as per existing colour by spray gun or by brush as applicable, over & inclduing primer coat of red oxide and including writing the SM No. / MES No. on DG Set in two inch block letter with synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 81 | M&L for preparing old painted surface by scraping with requisite tools of DG Set 63 kVA and applying two coats of 1st quality synthetic enamel paint as per existing colour by spray gun or by brush as applicable, over & inclduing primer coat of red oxide and including writing the SM No. / MES No. on DG Set in two inch block letter with synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge. |
| 82 | M&L for providing high temperature resistant exhaust rope packing around of DG Set of capacity 63/ 100/ 125/ 250/ 380 kVA, exhaust silencer joints/ flanges inluding removal of old packing proper fitting, sealing, tightening etc complete all as specified and as directed by Engineer-in-Charge. |
| 83 | M&L for Earthing with & including copper earth plate electrode 60 cm x 60 cm x 3.15 mm thick buried vertically in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the earth plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to & including copper strip 20 x 3.15mm as earth lead, including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted/welded to earth plate at one end and other end of strip connected to Panel / transformer / GOD / equipment body / test point with two Nos nuts bolts or welding with steel structure, Copper earth strip encased in and including 40mm bore GI light grade pipe with all fittings from upper edges of earth plate upto 7.5 metre above ground level fixed with and including 25x3mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe medium grade from earth pit to top of electrode and including funnel, wire mesh, copper lugs etc complete with earth pit in PCC 1:3:6 type C1 using 20mm graded crushed stone aggregate and 40mm thick RCC (1:2:4 type B1) cover complete all as specified and shown in electrical plate No 3 of SSR Part-I including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exc 50m complete all as specified and as directed including dismantling & taking out old existing unserviceable earthing of any type. |
| 84 | Servicing, repair, maintenance and attending complaint/ faults to the Fire Fighting and Fire alarm system including Fire Alarm Control Panel, Pre Alarm Action, Programmable detector sensitivity, Device type verification, Earth fault annunciation facility at 0 ohms, Double Address Sensing, Loop wise device test, 40 x 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day/ Night Mode facility, USB 2.0 interface for PC connectivity RS 485 Communication facility for network/ Repeater/ MODBUS/ BAC net. Programmable Auto Silence Facility, Programmable AC Loos delay. Programmable Silence Inhibit. Two Nos. of programmable inputs, Battery low audio, visual warning, Three programmable Form C relay for Fire, Fault and Supervisory maintenance complete all as directed.Note : New spare parts shall be measured and paid for separately. |
| 85 | Supply, installation, commissioning and testing of Analogue Addressable Fire Alarm Control Panel including detector wise configuration facility 2000 Event Storage with Real Time Clock, Upto 192 grouping facility, Pre Alarm Action, Programmable detector sensitivity. Device type verification, Earth fault annunciation facility at 0 ohms, Double Address Sensing, Loop wise device test. 40 X 4 Characters LCD display 2 numbers of loop card and 200 devices in any combination per loop. Day / Night Mode facility. USB 2.0 Interface for PC connectivity. RS 485 Communication facility for Network / Repeater / MODBUS / BACnet. Programmable Auto Silence Facility. Programmable AC Loos Delay. Programmable Silence Inhibit. Two Nos of programmable inputs. Battery low audio, visual warning. Three programmable Form C relay for Fire, Fault and Supervisory. Primary Power 120 / 220VAC + 10% -15%, 60 / 50 Hz. Standby Power 24V DC (2 Nos of 12V, 40 Ah (Max), Built in for 12Ah) Sealed Lead acid battery Operating Condition Operating Temperature 0 - 49°C / 32-120°F. Relative Humidity 93 ± 2% RH (non-condensing) at 32 ± 2°C / 90 ± 3°F including taking down old unserviceable Panel complete all as specified and as directed. |
| 86 | Supply, installation, commissioning and testing of Fire alarm control Panel in Gas release of Fire suppression Panel (RE-120GR) modular type, operates on 220 Volt AC supply, 16 x 2 LCD Dot Matrix Display, Compatible to all types of conventional detectors, Re-settable 24V DC output for 4 wire detectors & three 24V Sounder Output (Fire, after Cross zone, after Gas release), two mode operation facility (Auto/ Manual), Gas inhibit and Instant release facility, Manual Gas release with or without timer, Actuator pressure low sensing facility, RS 485 output for Repeater, Special logic circuitry to prevent accident release, auto re-settable fuse, surge protection also battery polarity & deep discharge protection, including taking down old unserviceable Panel complete all as specified and as directed. |
| 87 | Supply, commissioning and testing of Smoke detector Operating Voltage Range: 9 to 32 V DC Volts Non-polarized Standby Current: ≤100µA @ 24 V DC, Maximum Alarm Current (LED on) : ≤55mA @ 24 V DC, Operating Humidity Range: 10% to 93% Relative Humidity, Non-condensing, Operating Temperature Range: 14°F to 120°F (-10°C to 49°C), Adjustable Sensitivity: 1-2.5%/FT, Height: 2.2 (55 mm) installed in Base including taking down old unserviceable smoke detector complete all as specified and as directed. Make: Ravel Electronics Pvt Ltd/ Honey well / Agni/ Ceasfire/ Safex/ Flame Gurad Industries/ Nitin or equivalent make as approved by GE. |
| 88 | S&F in repair of Battery DC, 12V, 7 AH, lead acid duly initial charged complete all as specified and as directed. |
| 89 | Supply, commissioning and testing of Fire Alarm Hooter made out of iron, red colour operating voltage 24 DC supply Dimensions (L x B x H) : 18.5 cm x 13 cm x 7.5 cm including taking down existing fire alarm hooter complete all as specified and directed. Make: Ravel Electronics Pvt Ltd/ Honey well / Agni/ Ceasfire/ Safex/ Flame Gurad Industries/ Nitin or equivalent make as approved by GE. |
| 90 | Supply, commissioning and testing of Addressable manual call point resettable type including taking down existing addressable manual call point complete all as specified and as directed. Make: Ravel Electronics Pvt Ltd/ Honey well / Agni/ Ceasfire/ Safex/ Flame Gurad Industries/ Nitin or equivalent make as approved by GE. |
| 91 | S&F in repair first aid fire hose reel equipment conforming to IS: 884-1969 (with upto date amendments), finished with post office red spray paint and complete with and including 20mm dia 36 meters long hose tubing of approved make conforming to IS: 444, swinging type hose guide fixing bracket assembly, 25mm dia gate valve, 5mm outlet gunmetal nozzle with shut off valve as required complete all as specified and as directed. |
| 92 | S&F in repair Hydrant valve single headed Gun metal landing valve (internal/external Fire-Hydrants) with oblique type single outlet complete with hose coupling adaptor of 63 mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS 5290 complete all as specified and as directed. |
| 93 | S&F fire hydrant valve double headed Gun metal landing valve (internal/external fire hydrants) with B type double head outlet complete with hose coupling adaptor of 63mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS:5290 (ISI marked) including taking down old fire hydrant valve complete all as specified and as directed. |
| 94 | S&F fire hydrant valve four headed Gun metal landing valve (internal/external fire hydrants) with four head outlet complete with hose coupling adaptor of 63mm size, instantaneous spring lock arrangement and blank cap with chain conforming to IS:5290 (ISI marked) including taking down old fire hydrant valve complete all as specified and as directed. |
| 95 | S&F in repair Flanged stand post CI of 80 mm dia 1.5 m height complete all as specified and as directed. |
| 96 | S&F pressure switch universal type with & including wiring upto 10 mtr connection with suitable copper conductor cable, fixed in repairs, complete all as specified and as directed.Make :- DANFOSS / HONEYWELL / SIEMENS / HGURU / FIEBIG or equivalent as approved by GE. |
| 97 | S&F bourdon dial type pressure gauge 100 mm dia, suitable for range 0-21 Kg rating with brass isolation valve and pipe, fixed in repairs, complete all as specified & as directed.Make : FEBING / TAYLOR / HGURU / FIEBIG or equivalent as approved by GE. |
| 98 | S&F 150 mm bore Non Return butterfly valve (NRV) cast iron body, class PN 1.6, ISI marked, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return butterfly valve of 150mm bore. |
| 99 | S&F 150 mm bore butterfly valve cast iron body, class PN 1.6, ISI marked, single eccentric, double flanged short body type with all fittings, nuts, bolts and washers and necessary rubber gaskets etc., including taking down old butterfly valve compete all as specified and as directed. |
| 100 | S&F 50 mm bore butterfly valve cast iron body, class PN 1.6, ISI marked, single eccentric, double flanged short body type with all fittings, nuts, bolts and washers and necessary rubber gaskets etc., including taking down old butterfly valve compete all as specified and as directed. |
| 101 | Supply and fixing cast iron foot valve of size 100mm bore as per IS:4038 (ISI marked), flanged ends with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve of 100mm bore complete all as specified & as directed. |
| 102 | Supply and fixing cast iron foot valve of size 150mm bore as per IS:4038 (ISI marked), flanged ends with rubber insertion sheet 3mm thick, nuts, bolts and washers including taking down old existing unserviceable foot valve of 150mm bore complete all as specified & as directed. |
| 103 | Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 80 mm bore, complete all as specified & as directed. |
| 104 | Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 100 mm bore, complete all as specified & as directed. |
| 105 | S&F in repair Semi Automatic Star Delta Starter in sheet steel enclosure for 7.5 to 15 HP motor 415V, 50Hz, 3 Phase complete including connecting by using proper lugs complete.Make: L&T Model No. MK1 SASD. |
| 106 | S&F in repair fully automatic Star Delta starter in sheet steel enclosure for 40 to 60 HP motor pump 415V, 50Hz, 3 Phase with SPP feature complete including connecting by using proper lugs complete.Make: L&T Model No. MU-G50 FASD. |
| 107 | S&F in repair 3 Pole Power Contactor 45 Amp AC2 Rating, including necessary connections complete all as directed. Make: L&T Type \\"MNX 45” Cat No. ST19000. |
| 108 | S&F in repair 3 Pole Power Contactor 22 Amp AC2 Rating, including necessary connections complete all as directed. Make: L&T Type \\"MNX 22” Cat No. CS94980/ CS94981. |
| 109 | S&F in repairs single phase preventer, AC, 415 V, 50 Hz base mountable auto reset 1C/O output relay and trip time delay for unbalance 1 or 2 sec, including commissioning & testing complete all as specified & as directed. Make: ELLICO Model ESP-2. |
| 110 | S&F in repairs star delta electronic timer S/D-100, 230/ 415 V, 50 Hz, surface mounting, highly repeat accuracy and output relay contact 2 Nos. on time delay 0 to 30 sec, including commissioning & testing complete all as specified & as directed. Make: ELLICO Model S/D-100. |
| 111 | S&F in repairs DIN type Fuse Links type HN size 1, suitable for type FN 250/ 315/ FNX 250/315 S-D-F & for HB 250 fuse base of 415 volts, current rating upto 315 Amps complete all as specified & as directed. Make: L&T/ C&S/ ABB |
| 112 | S&F in repairs DIN type Fuse Links type HN size 0, suitable for type FN 200/ FNX 200 S-D-F & for HB 250 fuse base of 415 volts, current rating upto 200 Amps complete all as specified & as directed. Make: L&T/ C&S/ ABB or equivalent make as approved by GE. |
| 113 | S&F in repairs DIN type Fuse Links type HN size 14x51, suitable for type FN 63/ FNX 63 S-D-F & for HC 32 fuse base of 415 volts, current rating upto 63 Amps complete all as specified & as directed. Make: L&T/ C&S/ ABB |
| 114 | S&F in repairs TPN S-D-F type suitable fuse link of size fr3 range 200 amps to 250 amps current rating (HN size 0-1) conforms to IEC 60947-3, including terminal shrouds on both sides and phase barriers, telescopic shaft for depth adjustment including door interlock & padlock facility complete all as specified & as directed. Make: L&T/ C&S/ ABB |
| 115 | S&F in repairs TPN S-D-F type suitable fuse link of size fr1 range 2 Amps to 63 Amps current rating (HF size) conforms to IEC 60947-3, including terminal shrouds on both sides and phase barriers, telescopic shaft for depth adjustment including door interlock & padlock facility complete all as specified & as directed. Make: L&T/ C&S/ ABB |
| 116 | S&F in repair MCCB, 4 Pole, 250 Amps, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, adjustable Thermal - Magnetic release type including electric connection & testing complete all as specified and as directed. |
| 117 | S&F in repair MCCB, 4 Pole, 160 Amps, rupturing capacity 36 kA, 415 Volt grade, AC, 50 Hz, adjustable Thermal - Magnetic release type including electric connection & testing complete all as specified and as directed. |
| 118 | S&F in repair MCCB 4 Pole, 63 Amps, 16 kA, 415 Volts, 50 Hz, AC supply including electric connection & testing complete all as specified and as directed. |
| 119 | M&L for preparing old painted surface by scraping with requisite tools of 100/ 150mm bore fire main line and painting surfaces with two coats of 1st quality synthetic enamel paint with red colour over a coat of zinc chromate primer by spray gun or brush complete all as specified and as directed by Engineer-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysNov 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 16 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender