Tender For Special Repair /Replacement Of Sewage Pump Motors, Water Supply Pipeline & Bore Wells Against Ber At Certain Locations At Af Stn Bareilly.
Tender Overview
Project Description
Tender for Special Repair /Replacement Of Sewage Pump Motors, Water Supply Pipeline & Bore Wells Against Ber At Certain Locations At Af Stn Bareilly.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 10-Nov-2026 | Corrigendum | Date | 25-Nov-2026 |
| 2 | 19-Nov-2026 | Corrigendum 1 | Date | 04-Dec-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | M&L for drilling trial bore by rotary/ reverse rotary Method in any type of strata consisting of 250mm dia drill bit for depth up to 200m in sequence from ground level as given below for different bore wells complete as per IS -2800, part -1 |
| 2 | The following test and reporting will be carried out by the contractor and approved by GE all as per IS -2800, part 1(i) Recording the well discharge during drilling by a 90 degree V- notch.(ii) Recording the water bearing horizon.(iii) Taking the samples from the bore well cutting for every 3m interval and every change in strata if less than 3m.(iv) Preparation of litho logs based on these samples.(v) Drill time log to be prepared and prescribed.(vi) Aquifer performance tests at constant discharge with draw down and recovery reading. |
| 3 | The depth of trial boring of the tube well at the site indicated by the GE is anticipated to be 200 meter below ground level . The depth may, however be ordered in writing to be varied by the GE up to a maximum of 25 % of the above mentioned depth (plus or minus). If the GE decided that suitable water bearing strata is not available in the aforesaid bore or the boring can not be continued further on account of the type of strata met with, he may order the contractor to bore at other site(s) selected by the GE, until suitable water bearing strata is met with or boring cannot continue further on account of the type of strata met with provided the total number of bores (including the first bore) does not exceed two Numbers the decision of the GE shall be final & binding . |
| 4 | M&L for development of trial bore to be reamed by suitable size of bit to accommodate 300 X 200 mm dia assembly pipes leaving 5\\" annular space around assembly pipes from 250mm to 675 mm for 60 RM from ground level complete all as specified and directed. |
| 5 | M&L for development of trial bore to be reamed by suitable size of bit to accommodate 300 X 200 mm dia assembly pipes leaving 5\\" annular space around assembly pipes from 250mm to 525 mm from exceeding depth of 60 RM but not exceeding 200 meter below ground level complete all as specified and directed. |
| 6 | M&L for development of trial bore to be reamed by suitable size of bit to accommodate 300 X 200 mm dia assembly pipes leaving 5\\" annular space around assembly pipes from 250mm to 525 mm from exceeding depth of 200 RM but not exceeding 220 meter below ground level complete all as specified and directed. |
| 7 | Supplying and assembling including jointing, lowering & fixing in position plain mild steel sheet casing (seamless) pipe 300mm bore of thickness 6 mm confirming to IS: 4270-2001, pipe jointed and welded with coupler rings, Welding shall be done throughout the circumference of the pipe and coupler ring on both sides complete all as specified and directed. Make of Pipe :-Jindal/TATA/SAIL/PRAKASH SURYA/Jindal. |
| 8 | All as per item no 5 here in before but Supplying and assembling including jointing, lowering & fixing in position plain mild steel sheet casing (seamless) pipe 200mm bore of thickness 6 mm confirming to IS: 4270-2001, pipe jointed and welded with coupler rings, Welding shall be done throughout the circumference of the pipe and coupler ring on both sides complete all as specified and directed. |
| 9 | All as per item no 5 here in before but Supplying and assembling including jointing, lowering & fixing in position ERW slotted mild steel sheet casing (seamless) pipe 200mm bore of thickness 6 mm confirming to IS: 4270-2001, pipe jointed and welded with coupler rings, Welding shall be done throughout the circumference of the pipe and coupler ring on both sides complete all as specified and directed. |
| 10 | S&F mild steel reducing socket 300mmx200mm including welding MS strip 4mm X 6mm (6 Nos) on each joint extended 100mm on each side complete all as specified and directed. Note:- The Wall thickness of the socket side shall not be less than 7.04mm. |
| 11 | Chemical and bacteriological testing or water sample from approved laboratory to ensure potability of water complete all as specified and irected. |
| 12 | Supply & packing of pea gravel 3mm to 5mm size as per IS of natural shape brought directly from river bed and packing around the casing pipe/slotted pipe in the bore well to entire depth upto ground level complete all as specified & directed |
| 13 | Electric logging in pilot bore for precise delineation of granular zones as also the quality of ground water including report interpretation complete all as specified and directed.Note:- Electric logging shall be carried out by only approved Govt Agency. |
| 14 | M&L for development of tubewell by means of over pumping high velocity with 250 PSI Air compressor as specified in IS 8110-2000 para 3.4 complete all as specified & directed. |
| 15 | All as per item no 12 above but by means of over pumping for subsequent hours until clear discharge as per clause 9.3 of IS 2800 (Part-1)-2009 complete all as specified and directed. Note:- Over pumping will be carried out by pumping the well at higher capacity not less than 25% above the established well yield |
| 16 | Yield testing of the tube well to determine the safe pumping capacity of tube well by continuously pumping for 16 hrs complete all as specified and directed.Note:- Cost of pumping for yield test is included in item No. 12 above. |
| 17 | Lifting & lowering submersible pump, with SS Bowl and connected with 100 mm dia column pipe by means of SS flange and Connecting SS Nipple having dilfuser casing construction and impellers dynamically balanced rotor and pump shaft with impeller and motor suitable for operation on 3 phase 415 volts, complete set, head 54 Mtr, discharge range 1700 LPM not less than 10 HP including cable guard cable as per mfrs recommendation upto 02 run x50 meter etc complete all as specified and directed. |
| 18 | S&F polypropelene rope( Stainess Steel ) 28 mm dia, ISI marked, heavy duty grade for holding the submersible motor complete all as specified and directed |
| 19 | Supply & lowering 100 mm dia 3 Mtr long heavy grade MS ERW pipe with flange End including all fittings and fixtures complete all as specified & directed |
| 20 | Supply & Fixing of MS well cap of 300 mm nominal bore of pipe at the top of casing pipe of bore well with locking arrangement complete all as specified and directed |
| 21 | Supply & Fixing of MS bail plug suitable for 200mm nominal bore MS pipe including its fixing arrangements complete all as specified and directed |
| 22 | S&F 2 Nos MS flat iron 150mmx16mm thick size clamp for holding with 300mm bore housing pipe including casting of PCC block of size 1200mm x 1000mm x 1000mm in PCC (1:2:4) type B-1 using 20mm graded stone aggregate including 80mm bore MS pipe 2 Nos each, 1.5 metre long with cap plug and cap top for feeding pea gravel for each bore well complete all as specified and directed. |
| 23 | Supply and fixing of GI pipe 25 mm dia bore with required length of GI pipes, clamps etc complete all as specified and directed. |
| 24 | S&F of pressure gauge 0 to 10 Kg/cm square range with necessary siphon and 15 mm dia stop valve including 15 mm dia GI pipe, not exceeding 0.25 Mtr in length, 15 mm brass bib cock on rising main including drilling tapping on GI / CI pipe line complete all as specified and directed |
| 25 | M & L for strata (at every 3 meters depth) sample box of size 900 X 400 mm and 150 mm deep, made of 25 mm thick teak wood planks and size of sample bits 100 mm X 100 mm with front side provided with glazed hinged door shutter of size 900 X 400 mm provided with hasp & staple and painted for strata samples as found at the time of drilling the tubewell complete all as specified and directed. |
| 26 | M&L for borewell chart on acrylic sheet of size 60 cm x 30 cm duly marked permanent marking including 12mm thick plywood frame, clamps for fixing on wall etc complete all as specified and directed. |
| 27 | Supply, fixing and testing cast iron Non return Valve class heavy duty ISI marked, both ends flanged of size 150mm including fitting for connecting the line with jointing material complete all as specified and directed. |
| 28 | Supply and laying cast iron pipe 150mm bore with flanged ends, centrifugally cast, class B, in any length, laid in trenches or fixed to pillars and the like complete all as specified and directed. |
| 29 | Supply and laying in replacement of 100 mm dia trenches for galvanised steel tubes medium grade including all fittings complete all as specified and directed. |
| 30 | M&L for horizontal boring below pavement/road, in soft/loose soil for crossing 100mm to 25mm size GI pipe lines all as specified and as directed. |
| 31 | Supply, Laying and jointing of submersible cable 3 core multi stranded copper conductor PVC insulated, water proof, ISI marked of size 10 sqmm for connecting bore well submersible pump sets complete all as specified and directed. |
| 32 | Supply, Laying and jointing of submersible cable 3 core multi stranded copper conductor PVC insulated, water proof, ISI marked of size 16 sqmm for connecting bore well submersible pump sets complete all as specified and directed. |
| 33 | Supply, fixing and testing of chain pully block, triple spur gear, 2 ton capacity with 3 mtr lift, manually operated completed with hooks high tensile forged steel conforming to IS: 3815 and load confirming to IS:6216 and hand chain to IS:2429 (part-1) complete all as specified and directed. |
| 34 | Material and labour for GI water tubing , light grade, galvanized laid in trenches all required fitting of 50mm bore for protection of Submersible cable laid in trench complete all as specified and as directed. Make:- Tata / swastik/ Jindal/ prakash. |
| 35 | Supply ,installation and lowering submersible pump of capacity 10 HP with SS Bowl and connected with 150 mm dia column pipe by means of SS flange and Connecting SS Nipple having dilfuser casing construction and impellers dynamically balanced rotor and pump shaft with impeller and motor suitable for operation on 3 Phase 415 volts, complete set, head 40 mtr including cable guard cable as per manufacturer's recommendation etc complete all as specified and directed. Make:-Crompton greaves/KSB/Kirloskar. |
| 36 | Supply install Non clogging centrifugal pump of capcity 20 HP with SS Bowl and connected with 150 mm dia column pipe by means of SS flange and Connecting SS Nipple having dilfuser casing construction and impellers dynamically balanced rotor and pump shaft with impeller and motor suitable for operation on 3 Phase 415 volts, complete set, head 55 to 70 mtr, discharge range 800 to 900 LPM including cable guard cable as per mfrs recommendation etc complete all as specified and directed. Make:-Crompton greaves/KSB/Kirloskar. |
| 37 | Supply and fixing indoor type cubical compact Panel design 415 volts 50Hz 4 wire fabricated from inner thickness self moulded type and 50x50x6 mm angle iron frame front opening with double shutter and locking arrangement with 50mm lock and including grouting of panel with necessary PCC 1:2:4 type B-1 powder coated paint after pre-treatment of surface, openable from front side including submersible pump starter with 3 position selection (with auto switch )star delta starters 01 Nos, automatic phase sequence corrector, with short circuit protection, MCCB TP, Digital type volt and ammeter selector switch suitable CT's, Indicator lamps etc suitable for 20/25 HP Submersible Pump complete all as specified and directed. |
| 38 | Supply and fixing indoor type cubical compact Panel design 415 volts 50Hz 4 wire fabricated from inner thickness self moulded type and 50x50x6 mm angle iron frame front opening with double shutter and locking arrangement with 50mm lock and including grouting of panel with necessary PCC 1:2:4 type B-1 powder coated paint after pre-treatment of surface, openable from front side including submersible pump starter with 3 position selection (with auto switch) star delta starters 01 Nos, automatic phase sequence corrector, with short circuit protection, MCCB TP, Digital type volt and ammeter selector switch suitable CT's, Indicator lamps etc suitable for 10/15 HP Submersible Pump complete all as specified and directed. |
| 39 | Supply, Fixing & testing of 100 mm bore CI Foot valve, ISI marked , Confirming to IS 4038 class PN 1.6 with Spindle brass (Heavy duty) Wheel head and both ends flanged and MS nut bolts and washers and pair of rubber/fiber gasket and fixed in position complete all as specified and directed. |
| 40 | Supply, Fixing & testing of 150 mm bore CI Reflux valve with by pass arrangement, ISI marked, PN 1.6 with Spindle brass (Heavy duty) Wheel head and both ends flanged and MS nut bolts and washers and pair of rubber/fiber gasket and fixed in position complete all as specified and directed. |
| 41 | Taking out from trenches CI pipe lines (including all fittings) with spigot & socket ends with lead joints etc. including taking out lead from joints complete all as specified & directed. Note:- Earth work shall be measured & paid separately. |
| 42 | 150 CI pipe mm bore |
| 43 | 100 CI pipe mm bore |
| 44 | Supply, laying, jointing and testing in replacement of Ductile iron pipe socket and spigot end class conforming to IS : 8329:2000 of class \\"K-7\\", size of 150 mm (6\\") dia with socket and spigot ends with rubber gasket (Tyton joints) centrifugally cast in any length laid in trenches complete all as specified and directed. |
| 45 | Supply, laying, jointing and testing in replacement of Ductile iron pipe socket and spigot end class conforming to IS : 8329:2000 of class \\"K-7\\", size of 100 mm (4\\") dia with socket and spigot ends with rubber gasket (Tyton joints) centrifugally cast in any length laid in trenches complete all as specified and directed. |
| 46 | Supply and fixing DI Specials such as Bends (Conforming to IS-9523:2000) for PRESSURE PIPE FOR WATER, (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \\"Y\\" junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs upto 150 mm bore complete all as specified and directed. |
| 47 | Supply, Fixing & testing of 150 mm bore CI Sluice valve, ISI marked , Confirming to IS 14846-2000 class PN 1.6 with Spindle brass (Heavy duty) Wheel head and both ends flanged and MS nut bolts and washers and pair of rubber/fiber gasket and fixed in position complete all as specified and directed. |
| 48 | Supply, Fixing & testing of 100 mm bore CI Sluice valve, ISI marked , Confirming to IS 14846-2000 class PN 1.6 with Spindle brass (Heavy duty) Wheel head and both ends flanged and MS nut bolts and washers and pair of rubber/fiber gasket and fixed in position complete all as specified and directed. |
| 49 | Supply and fixing Cast iron Air valve with two air outlets, 50mm dia bore and fixing Up in DI water supply mains 150 mm dia bore complete all as specified and directed. |
| 50 | Material & Labour for brick masonry valve pit of internal size 120cm x 120cm x 120cm suitable for sluice valves upto 100mm size, with PCC 1:4:8 type D-2 for foundation, brick work in cement mortar 1:6 rendering 1:4, 15mm plastering, coping in PCC 1:2:4 type B-1, including necessary earth work, including MS sheet cover of thickness 3.15mm on 50X50X6 mm angle iron framework including two coats of synthetic enamelled paint over a coat of red oxide primer with making provision of locking arrangement including demolished old valve pit complete all as specified and directed. |
| 51 | Excavation in trenches not exceeding 1.5 mtr wide & not exceeding 1.5 mtr deep for laying pipe lines etc & getting out in Soft/loose soil including forming bottom surface to required level or slope complete all as specified and directed. |
| 52 | Returning, filling in trenches (Soft/Loose soil ) in layers not exceeding 25 mm thick after laying of pipe including spreading, levelling & well ramming including watering as required complete all as specified and directed. |
| 53 | Removing surplus excavated soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above from the starting point complete all as specified and directed. |
| 54 | Material and labour in replacement of old defective earthing by providing new earthing comprising of galvanised steel earth plate electrode 600x600x6mm thick, buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to Galvanised earth lead strip 25x4 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end connected to earthing testing point including funnel with watering pipe of 20 mm bore medium grade galvanised iron, wire mesh, charcoal or coke and common salt in alternate layers of 15cm .(compacted thickness) all around the earth electrode with concrete earth pit in PCC (1:3:6) type C-1, 50 mm thick pre-cast RCC M-20 nominal mix cover slab of size 450mm x 450mm reinforced with 8 mm dia TMT bar 10 cm C/C and suitable handle of 10mm dia round bar including necessary excavation, earth work in any type of soil and disposal of spoil to a distance not exceeding 50 m including GI protection pipe light grade 40mm bore and necessary testing compete all as shown in Electrical Plate No 5 of MES SSR Part I as shown on drawing including testing on completion, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Tender Published
Tender notice published.
CompletedCorrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysCorrigendum-2 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 12 daysBid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysBid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender