Tender For special Repair Of Or Living Bldg No 2/03/01/D/5/6 And 2/03/01/D/7/8 Of Certain Unit Under Ge (S) Binnaguri
Tender Value
68.10 Lakhs
Estimated cost
Bid Submission
07 Dec 2026
25 days left
EMD
1.28 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair Of Or Living Bldg No 2/03/01/D/5/6 And 2/03/01/D/7/8 Of Certain Unit Under Ge (S) Binnaguri
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 10-Nov-2026 | DATE AMDT | Date | 07-Dec-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | PART-I : (B/R WORKS) Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed. |
| 2 | Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 3 | Demolition and breaking up including removing salt glazed stoneware pipe 150 mm bore (internal) with concrete bedding and haunching complete including necessary earth work as required complete all as specified and as directed. |
| 4 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for, complete all as specified and as directed. |
| 5 | Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, approaches, dado/Partitions etc, complete all as per specified and as directed. |
| 6 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5 Sqm each and removing from site, complete all as specified and as directed. |
| 7 | Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5 Sqm but not exceeding 4.00 Sqm each and removing from site, complete all as specified and as directed. |
| 8 | Taking down cement plaster on brick wall of any description, including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 9 | Taking up or down 15 mm steel tubing and connections, including cleaning for refixing or removal to store, complete all as per specified and as directed. |
| 10 | Taking up or down 20 mm steel tubing and connections, including cleaning for refixing or removal to store, complete all as per specified and as directed. |
| 11 | Demolition of brick work or rubble stone masonry including all quoins arches, pillars etc. built in cement mortar and including removal from the site, complete all as specified and as directed. |
| 12 | Dismantling water tanks of capacity exc. 500 and not exc. 1000 ltrs, complete all as per specified and as directed. |
| 13 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as per specified and as directed. |
| 14 | Removing existing water proofing treatment to complete any description/any thickness and in any position up to main slab including removal of rubbish of the premises etc complete all as specified and as directed. |
| 15 | Excavation in trenches n.exc 1.5m wide and n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 16 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil, complete all as per specified and as directed. |
| 17 | Removing excavated soil material not exc. 50 m & depositing where directed at a level not exc. 1.5 m above starting point complete all as specified and as directed. |
| 18 | M&L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work, complete all as per specified and as directed. |
| 19 | M&L for PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 20 | M&L for plain cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in surface channels and drains, complete all as specified and as directed. |
| 21 | M&L for PCC (1:2:4) type B1 (20mm graded aggregate) as in slabs, landing, shelves chajjas and in roof kerbs, slightly rounded or chamfered on edges, mixed with water proofing compound 200 ml per beg of cement or as per manufacturer instructions finished even and smooth on exposed concrete surface without using extra cement, complete all as specified and as directed.(Note: Water proofing compound shall be measured and paid separately under relevant item of this schedule). |
| 22 | M&L for precast cement concrete (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in landings, cover slabs (for manholes etc.) shelves and similar articles with plain faces set in cement mortar 1:4, complete all as specified and as directed. |
| 23 | M&L for RCC type B1 (1:2:4) using 20 mm graded crushed aggregate in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like, complete all as specified and as directed. |
| 24 | M&L for fly ash brick work with old size bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:4, complete all as per specified and as directed. |
| 25 | M&L for 16 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of granite stone including griding & polishing with 20 mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and as directed. |
| 26 | M&L for 35 mm thick second class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of member (Bottom 250mm, stiles 100mm, top 120mm & lock rail 160mm wide) as specified in SSR part I section & clause 8.24 (a) complete all as specified and as directed. |
| 27 | S&F factory made 2nd class hard wood rail and style 35mm thick plain framed, panelled shutter (two panel ) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS:1003 (part I), kiln seasoned and chemically pressure treated, complete all as per specified and as directed. |
| 28 | S&F of factory made Solid PVC Door Frame of size not less than 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as per specified and as directed. |
| 29 | Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. .frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as per specified and as directed. |
| 30 | S&F of 100 mm long stainless steel butt hinges medium weight, complete all as specified and directed. |
| 31 | S&F of 150 mm mild steel tower bolts stove enamelled black with bright, complete all as per specified and as directed. |
| 32 | S&F of 150 mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed. |
| 33 | S&F of 200 mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed. |
| 34 | S&F of 250 mm long mild aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as per specified and as directed. |
| 35 | S&F of 125 mm long aluminium handles, cast type, anodised, complete all as per specified and as directed. |
| 36 | S&F in repair of 25mm dia curtain rod, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as per specified and as directed. |
| 37 | S&F in repair of brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as per specified and as directed. |
| 38 | S&F of stainless steel wire cloth, 0.36 mm dia of wire and average width of aperture 1.40 mm and fixed with tinned stacks, or galvanized wire staples complete all as per specified and as directed. |
| 39 | M&L for Mild steel TMT bars 6 to 8 mm dia. cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips, complete all as per specified and as directed. |
| 40 | S&F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 41 | S&F of steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed. |
| 42 | S&F in repair Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete all as per specified and as directed. |
| 43 | M&L for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as per specified and as directed. |
| 44 | M&L for Pressed steel frames of size not less than 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as per specified and as directed. |
| 45 | M & for water proofing treatment to sunken floor with the following course of treatment/ specification: (i) Cleaning top surface of floors /slabs and laying 50 mm thick (avg) PCC of grade M10 (Nominal mix) , mixed with WPC as per manufactrrer's instruction laid in slope 1:20 towards spouts including coveting corners(ii) 15 mm thick plastering in CM (1:4) on sides mixed with WPC as pe rmanufacturer's instruction.(iii) Applying 1st layer of slurry @ 0.488 kg / sqm mixed wth acrylic based polymer modified cementious compound @ 0.253 kg /sqm This layer shall be allowed to air cured for 4 hrs.(iv) applying 2nd layer of slurry @ 0.242 kg/sqm mixed with accrylic based polymer modified cementenous compound @ 0.126 kg/sqm.This layer shall be allowed to air cured for 4hrs followed with water curing for 48 hrs.(v) Applying a coat of industrial bitumen 85/25 penetration @ 1.50 kg/sqm on plastered and concrete surfaces(vi) Providing 150 micron thick polyutethene paint in two coats (each of 75 micron measured dry on dry surface over a coat of PU primer including preparation.(vii) 2 Nos 32mm bore GI medium grade 450mm long spout ,to be provided through external wall to drainout accumulated water.(viii) Sunken floor shall be tested for water tighness by filling water for 72 hrs before and after treatment work is carried out and ensure that no leakage /seepage exists(ix) Sunken portion shall be filled with lean concrete 1:4:8 type D2. |
| 46 | M&L for water-proofing treatment to RCC roof slab including parapet, comprising the following course of treatment (applied from bottom to top):(a) Applying bituminous primer @ 0.70 litre per Sqm over prepared plastered surfaces of the roof including parapet surfaces.(b) Over the priming coat, laying one layer of APP-based polymeric membrane, 3 mm thick, weighing not less than 3.50 Kg/Sqm, reinforced with non-woven polyester fabric weighing not less than 160 gsm. The membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of the parapet.(c) Applying two coats of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning.The laying of APP-based polymeric membrane shall be done by torch-on method or as per manufacturer’s instructions.Notes:(i) A minimum overlap of 150 mm shall be provided at the length sides and 100 mm at the width sides of the APP-based polymeric membrane and sealed as per manufacturer’s instructions.(ii) APP-based polymeric membrane shall be of approved quality conforming to the required specifications. |
| 47 | M&L for 25 mm thick PCC (1:2:4) type B-0 (12.50 mm graded stone aggregate) , as in roof to achive slope on existing roof surface, complete all as specified and as directed. |
| 48 | S&F of coloured non-skid ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:6 complete all as per specified and as directed. |
| 49 | S&F of coloured non-skid ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10 mm thick backing coat in Cement Mortar 1:4 complete all as per specified and as directed. |
| 50 | M&L for coloured glazed ceramic tiles not less than 450X 350X 7mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 10 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed. |
| 51 | S&F of coloured non-skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in Cement Mortar 1:6 complete all as per specified and as directed. |
| 52 | M&L for 75 mm thick PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in plinth protection/ footpath/ steps finished cement concrete surface even & fair etc complete all as specified and as directed. |
| 53 | S&F of 4 mm thick sheet glass of ordinary quality in squares not exc. 0.5 sqm in each pane glazing with oil putty complete all as per specified and as directed. |
| 54 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including provn of two Nos 3x3 mm grooves at tread of each step laid over 15 mm thick screed bed or bedding layers in Cement Mortar 1:6 complete all as specified and as directed. |
| 55 | M&L for machine cut kota stone 20-25 mm thick for vertical surfaces like staircase steps (risers), skirting, in single piece (of length not more than 1200mm), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and beewax polishing over 15 mm thick bedding layers in Cement Mortar 1:4, complete all as specified and as directed. |
| 56 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as per specified and as directed. |
| 57 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound, surface even & smooth without using extra cement, complete all as specified and as directed.Note: WPC shall be measured and paid separately. |
| 58 | M&L for 5mm thick rendering plastering on fair faces of brick work or concrete surface in cement mortar (1:3) and surface even and smooth without using extra cement, complete all as specified and as directed. |
| 59 | M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar (1:6) and surface finished even and smooth without using extra cement complete all as specified and as directed. |
| 60 | Supply only Liquid water proofing compound confirming to IS complete all as per specified and as directed. |
| 61 | M&L for preparation of new plaster surfaces of walls and applying two coats of Acrylic smooth exterior paint (using AIR-LESS PAINT SPRAYER) @ 1.67 litre/ 10 sqm over and including 2mm thick wall care cement based putty in two layer (each layer of 1mm thick) on wall surfaces by using AIR-LESS PAINT PRIMER SPRAYER using smart technique and using manual sand papers(where reqd) of approved grade complete all as specified and as directed. |
| 62 | M&L for complete removal of existing treatment and finishing the walls with applying two coats of Acrylic smooth exterior paint (using AIR-LESS PAINT SPRAYER) @ 1.67 litre/ 10 sqm over and including 2mm thick wall care cement based putty in two layer (each layer of 1mm thick) on wall surfaces by using AIR-LESS PAINT PRIMER SPRAYER using smart technique including preparation/levelling of old surface of wall using manual sand papers(where reqd) of approved grade complete all as specified and as directed. |
| 63 | M&L for preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed. |
| 64 | M&L for preparing old plastered surface of ceiling and applying three coats of white wash etc., complete all as specified and as directed. |
| 65 | M&L for preparing old plastered surfaces and applying two coats of distemper oil emulsion complete all as specified and as directed. |
| 66 | M&L for preparing new plastered surfaces and applying two coats of distemper oil emulsion complete all as specified and as directed. |
| 67 | M&L for preparation of new or previously untreated steel or iron surface of any description and applying two coats of synthetic enamel paint over a coat of red oxide, primer over 10cm width or girth complete all as specified and as directed. |
| 68 | M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed. |
| 69 | S&F of GI tube 15 mm bore medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 70 | S&F of GI tube 20 mm bore medium grade with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed. |
| 71 | S&F of rotational moulded PVC water storage tank 1000 litres capacity conforming to IS-12701(1989) cylindrical vertical type multi-layered (not less than three layers) with closed top including inlet, outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part-I, 2009 etc., complete all as specified and as directed. |
| 72 | S&F in repair of 15mm dia bore fancy type pillar tap cast copper alloy with capstan heads chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as per specified and as directed. |
| 73 | S&F of Bib taps fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule, complete all as per specified and as directed. |
| 74 | S&F in repair of stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union, complete all as per specified and as directed. |
| 75 | S&F in repair of 20 mm ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minimum weight 15mm-142gms/ 20 mm) and fixed in position complete all as per specified and as directed. |
| 76 | S&F of PVC connection 15mm dia with PTMT nuts of length 600 mm, complete all as per specified and as directed. |
| 77 | M&L for concrete bed 1:3:6 type C2 (40 mm graded stone aggregate) to 150 mm dia. drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested, complete all as per specified and as directed. |
| 78 | S&F in repairs Brass chromium plated shower rose 75mm size with or without swivel joints, any size, including fixing to steel pipe or union, complete all as per specified and as directed. |
| 79 | S&F ceramic undercounter wash hand Basin Glossy finishes, size 22x16x8 inch size including CP waste coupling, PVC connection 450 mm long, waste pipe and removing the existing Basin, cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed. |
| 80 | S&F in repair of 600x450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as per specified and as directed. |
| 81 | S&F in repair of vitreous china squatting pan \\"Orissa\\" pattern size 580x440mm white with integral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S\\" trap from or back inlet etc including connection to trap and flushing pipe and provision of lime concrete bedding, complete all as per specified and as directed. |
| 82 | M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for pipe of internal dia. 150mm, complete all as specified and as directed. |
| 83 | S&F in repairs coloured Vitreous China, pedestal pattern (Anglo-Indian Type) white (excluding flushing cistern & flush pipe) including connection to out going pipe, & seat cover and flushing pipe, complete all as per specified and as directed. |
| 84 | S&F in repair of plastic water closet seat cover, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as per specified and as directed. |
| 85 | S&F in repair of PVC valveless, symphonic action type 10 litre capacity low level flushing cistern, white, with inlet, ball valve, float and handle including brackets and 32 mm bore PVC flush pipe, complete all as per specified and as directed. |
| 86 | S&F in repair of Vitreous China urinals, Half stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as per specified and as directed. |
| 87 | S&F in repair 15 mm bore angle cock CP with flage complete all as per specified and as directed. |
| 88 | S&F in repair of towel Ring Round chromium plated , including all necessary fittings, connections etc. complete all as per specified and as directed. |
| 89 | S&F of soap dish Stainless steel fixed to wall with screws, complete all as per specified and as directed. |
| 90 | S&F in repair of Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete all as per specified and as directed. |
| 91 | S&F in repair of 75mm PVC (SWR) floor trap with grating including jointing with solvent cement complete all as per specified and as directed. |
| 92 | S&F of 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls, complete all as per specified and as directed. |
| 93 | S&F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls, complete all as per specified and as directed. |
| 94 | S&F of PVC (SWR) 110 mm bore bends with access door complete all as per specified and as directed. |
| 95 | S&F PVC (SWR) junction single (single T) equlal or un equal of 110 mm bore pipe with access door complete all as specified and directed. |
| 96 | S&F in repair of 110 mm dia PVC (SWR) branch piece, single (single Y) equal or unequal, complete all as specified and as directed. |
| 97 | S&F in repair of glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard & railing 60 cm long, complete all as per specified and as directed. |
| 98 | S&F of 150 mm internal diameter of double wall corrugated (DWC) high density polyethylene pipes (HDPE) and stiffness classes-8 (SN-8) with ISI marked (with CML no) with and including all fitting & jointing material for sewage line and laid in trenches as specified in IS: 16098-2013, Part-2 complete all as specified and as directed. |
| 99 | (SCHEDULE 'A' PART -II (ELECTRICAL WORK)Taking down carefully old unserviceable copper/ aluminium point wiring (light, exhaust fan, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, bells, sockets, tube light fittings etc., and making good disturbed surface of walls & Floors etc., complete all as specified and as directed. |
| 100 | M&L for point wiring with 1.5 sqmm size (nominal area) PVC insulated unsheathed single core multi stranded FR-LS copper conductor with proper colour coding cable drawn into and including PVC conduit of adequate size with all accessories concealed in wall/fixed to roof, ceiling etc (including cutting chases & making good the disturbed surface to its original specification) including MS sunk box, 3 mm thick phylum sheet top cover fixed by means of brass machine screw and cap washer including size 1.5 sq mm (nominal cross sectional area) PVC insulated unsheathed single core multistranded copper conductor cable as earth continuity conductor connected to main switches/DB's or common earth dolly complete all as specified and as directed for one light point controlled by one switch, complete all as per specified and as directed. |
| 101 | All as per serial item No.100.00 above but for one ceiling/exhaust fan point controlled by one way switch. |
| 102 | All as per serial item No.100.00 above but for one socket outlet 5/6 AMPs on independent board. |
| 103 | All as per serial item No.100.00 above but for one socket outlet 5/6 AMPs on same board. |
| 104 | All as per serial item No. 100.00 above but with 2.5 sqmm single core multistranded copper conductor including provision of 2.5 Sqmm PVC insulated multistranded unsheated copper conductor cable FR-LS (ISI marked) with proper colour coding as earth continuty cconductor connected to comon earth dolly for one socket out let 15/16 AMPs point on the independent board, complete all as specified and as directed. |
| 105 | S&F of switch piano flush type, 5/6 Amps 240 volts single pole one way, complete all as specified and as directed. |
| 106 | S&F of Switch piano, flush type single pole, one way 15/16 Amp, complete all as specified and as directed. |
| 107 | S&F of Socket outlet 2 in 1, 5 pin, 5/6 Amp, complete all as specified and as directed. |
| 108 | S&F of Socket outlet 2 in 1, 5 pin, 6 and 16 amp flush type, complete all as specified and as directed. |
| 109 | Supply and fix of fan regulator electronic type, rotary step (speed regulation in 5 steps), SP 240 Volt, suitable for ceiling fans complete all as specified and as directed. |
| 110 | Supply and fixing of Lamp holder, insulated with back plate suitable for batten/angle fittings complete all as specified and as directed. |
| 111 | S&F of LED white glass Lamp 1x9 Watt 230V Base-22, complete all as specified and as directed. |
| 112 | Supply and of fix ceiling rose surface PVC three terminals, PVC/ polycarbonate, insulated body, complete all as specified and as directed. |
| 113 | S&F LED lights fitting 1x 18W, 220V AC decorative box type with driver,IP 20, class I, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed connecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose complete with all accessories internally prewired and including necessary taking down the old unserviceable fitting complete all as specified and as directed. |
| 114 | S&F LED lights fitting 1x 10W, 220V AC decorative box type with driver,IP 20, class I, wall/ surface mounted, integrated type with extruded aluminium housing integrated high efficiency electronic driver and surge suppressor of 4KV or more, luminaire efficiency not less than 120 lumens/watt, power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz fixed connecting up with 2/3 core flexible copper conductor cable of suitable size from ceiling rose complete with all accessories internally prewired and including necessary taking down the old unserviceable fitting complete all as specified and as directed. |
| 115 | Supply and fixing LED security light fitting 25 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection luminaire efficiency not less than 100 lumens/watts integrated high efficiency electronic driver and surge suppressor of 7.5KV or more power factor not less than 0.90, CRI 80, THD 10%, operating range - 140 to 270 V, 50 Hz and necessary mounting arrangements, provision of new 2/3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fittings, complete all as specified and as directed. |
| 116 | Taking down carefully Ceiling fan from its original position and refixing / hanging after plaster work including painting of ceiling fan complete, in situ with synthetic enamel paint by spraying including filling cavities with filler one coat after cleaning all dust etc, complete all as specified and as directed. |
| 117 | M&L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked) cable 1100 volts grade, FR-LSH type, PVC insulated, unsheathed, flexible, multi stranded colour coded cables drawn through and including rigid PVC conduit of required size medium grade (MMS) with all connected accessories such as Bend, Tee, Elbow, Short pieces etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, FR-LSH type as earth continuity conductor connected to common earth dolly and including chease cutting and filling the same with cement mortar and finished with putty and making good the disturbed surfaces to match with existing surface as required for concealed work including taking down old u/s sub main wiring complete all as specified and directed . |
| 118 | Supply and fixing of sheet metal enclosure powder painted for MCB TP & N 6 way double door DB, 415 Volts, 200 Amp with din rail and bus bar including making good to the disturbed surface matching with the existing including taking down old unserviceable one, complete all as specified and directed. |
| 119 | Supply and fixing of sheet metal enclosure powder painted for MCB SPN 8 way double door DB, 240 Volts, 200 Amp with din rail and bus bar including making good to the disturbed surface matching with the existing including taking down old unserviceable one, complete all as specified and directed. |
| 120 | Supply and fix of sheet metal enclosure powder painted for MCB SPN 4 way double door DB, 240 Volts, 200 Amp with din rail and bus bar including making good to the disturbed surface matching complete all as specified and as directed. |
| 121 | S&F of MCB, Tripple pole & neutral 63 Amps,415 volts 'C' curve 10 KA, complete all as specified and as directed. |
| 122 | S&F of in replacement MCB, SPN, 6 Amps to 32 Amps , 'C' series, 240 Volt, 10KA, 50 Hz, complete all as specified and directed |
| 123 | Supply and fixing of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and as directed. Please Enable Macros to View BoQ information |
| 124 | Supply and fixing of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Nov 10, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Dec 07, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 25 daysDec 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 25 daysDec 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 27 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender