Tender For Detail Estimate For Construction Of Guard Room At Tiril Mauja Under J.S.H.B. Ranchi Division Harmu Housing Colony Ranchi
Tender Value
10.54 Lakhs
Estimated cost
Bid Submission
28 Oct 2026
0 days left
EMD
21084
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ranchi → Jharkhand
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Detail Estimate For Construction Of Guard Room At Tiril Mauja Under J.S.H.B. Ranchi Division Harmu Housing Colony Ranchi
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 22-Oct-2026 | Technical Bid | Technical Bid | 28-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation in foundation trenches in ordinary soil(vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M including all lifts,levelling,ramming the foundation trenches,removing roots of trees,shurbs all complete as per approved design,building specification and direction of E/I . |
| 2 | Extra for earthwork in hard soil as per building specification and direction of Engineer Incharge |
| 3 | Earth filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification Ε/I (Mode direction measurement compacted volume) |
| 4 | Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume) |
| 5 | Providing designation 75B one brick flat soiling joints filled with local sand including cost of watering taxes & royalty all complete as per building specification and direction of E/I. |
| 6 | Providing designation 75A one brick flat soiling joints filled with local sand including cost of watering taxes & royalty all complete as per building specification and direction of E/I. |
| 7 | Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing 1:1.5:3 (1 Cement: 1% coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 8 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of AND centering, shuttering and finishing:1:2:4 (1 Cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size) |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) |
| 10 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20mm nominal size). |
| 11 | Centering and shuttering including structting, Propping etc. and removal of form for Lintels, Beam, Plinth Bemas, Girders, bressumers and Cantilivers |
| 12 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets,columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size ) |
| 13 | Centering and shuttering including structting, Propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Strusts |
| 14 | Providing, hoisting and fixing above plinth level up to floor five level precast Reinforced cement concrete in lintels, beams and bressumers, including setting in cement mortar 1:3 (1 cement: 3 coarse sand), cost of required centering and shuttering but, excluding the cost of reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III):3 graded stone aggregate 20 mm nominal size) |
| 15 | Reinforced cement concrete work in arches, archribs, domes, Vaults, shells, folded plate and roofs having slope more than 15° up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size). |
| 16 | Centering and shuttering including structting, Propping etc. and removal of form for Suspended Floors, Roofs, Landings, Balconies and access platform |
| 17 | Providing designation 75A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials raking out joints to 15 mm depth, curing, taxes & royalty all complete as per building specification and direction of E/I. |
| 18 | Providing designation 125 mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15 mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/l. |
| 19 | Providing 12 mm Thk. cement plaster(1:6) with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I |
| 20 | Providing 12 mm Thk. cement plaster(1:4) with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I |
| 21 | Providing 1.5mm. cement punning including curing, carriage of water withall leads and lifts as per building specification and direc-tion of E/I. |
| 22 | Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of EI |
| 23 | Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/l. |
| 24 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS: 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry@ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc, complete. |
| 25 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 26 | S/F M.S. grill made of 20 x 6mm M.S. flat as per approved design and drawing, properly fabricated with joints continous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction ofE/I. (Where materials is not supplied by the deptt.) |
| 27 | Supplying fitting and fixing 20 guage G.C.I. sheet gate/ Window fitted on M.S. Angle frame of size 60x60x6mm, including cost of fabrication, providing necessary locking arrangement with haskal and domny dulu fixed in P.C.C. (1:24) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I |
| 28 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb |
| 29 | Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I |
| 30 | Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twi rubber stopper. |
| 31 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- incharge Extruded section profile size 48x40 mm |
| 32 | Providing and fixing to existing door frames.24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). |
| 33 | Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of Ε/I. |
| 34 | Providing Primer two coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. |
| 35 | Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/1. |
| 36 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 37 | Providing and fixing fan hooks of 16mm dia M.S. bar & 1 meter long, bent torequired size and shape, placed in position and fixed in the R.C.C.slab/beam at the time ofcasting all complete as per building. specification and direction of E/I. |
| 38 | providing Tor steel reinforcement of rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL) 8 mm Dia |
| 39 | 10 mm Dia |
| 40 | 12 mm Dia |
| 41 | Bricks 8 km |
| 42 | Local Sand (15 Kms) |
| 43 | Cement + Steel ( L - 1 Km ) |
| 44 | Stone Chips=20 km |
| 45 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools, driling rig,air compressureand equipmentsas well as lubricantsand cost of transportation of rig machine fule, annd other vehical up to Site. a) From 0.00 M to 50.00 M below G.L. |
| 46 | (b) From 51.0 M to122.00 M |
| 47 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia |
| 48 | Development of tube well in accordance with IS: 2800 (part 1) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \\"V\\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 49 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia |
| 50 | Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part 1), including necessary bolts & nuts of required size complete. 200 mm clamp |
| 51 | Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump 100mm set dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP. |
| 52 | Supplying Fully automatic star delta starter to operate induction mator working on 415v,3phase,50 hz with no volt coil, Over load element, ON-OFF push buttons, with necessary materials and connected to supply, etc complete starter with original sheet steel encloser F.A.S.D starter 20 H.P. |
| 53 | Wiring in existing conduit :-Supplying and drawing following sizes of FR PVC insulated copper /conductor single core cable in existing surface / recessed steel / PVC conduit including dismantling as required 3X4 sq.mm |
| 54 | Providing and supplying in standard lengths High Density Polyethylene Pipe (HDPE Pipe) confirming to IS 4984/14151/12786/13488 (Latest Revision with necessary jointing materials like mechanical connector l.e. thread/insert joint/quick release coupler joint/compression fitting joint or flanged joints excluding coupler/specials and taxes). Note: The Rates are F.O.R at worksite in Jharkhand including Royalty, inspection Charges and other taxes but excluding GST & C.P. HDPE pipe of materials grade PE80-PN06 (dia in mm) |
| 55 | Providing designation 75A brick work in C.M. (1:4) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials raking out joints to 15 mm depth, curing, taxes & royalty all complete as per building specification and direction of E/I. |
| 56 | Providing 12 mm cement plaster (1:3) with clean course sand of F.M. 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I & Providing 1.5mm cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of Ε/Ι. |
| 57 | Providing PCC M-150 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification & direction of E/I. |
| 58 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 59 | Supplying, fitting and fixing viterous white glazed earthen ware L.W.C. of Parry Hindustan or any other 1.S.S. approved make with 100 mm H.C.I., \\"p\\" trap 15 litres C... or C. pull and let go flushing cistern of names or other 1.5.5. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. A) 580 mm. long (b) With 12.5 lit. low level C.I. cistern |
| 60 | Providing and fixing male ended 15 mm dia brass bib cock of approved quality (wt not less than 350 gms) with extra socket all complete as per specification and direction of E/l. |
| 61 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. |
| 62 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to 15:8931 a) 15 mm nominal bore 15mm nominal bore |
| 63 | Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 min nominal bore, weighing not less than 32 gms |
| 64 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./H.P.H.D. plastic ball.25 mm nominal bore |
| 65 | 40 mm nominal bore |
| 66 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm |
| 67 | Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l. |
| 68 | 125 mm nominal dia with 25 mm waste hole |
| 69 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length |
| 70 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, 110mm diameter for waste water |
| 71 | Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion. 110 mm Single tee with door |
| 72 | 110 mm bend |
| 73 | 110mm Coupler |
| 74 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/e fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engincer in Charge. 15 mm nominal outer dia Pipes |
| 75 | 20 min nominal outer dia Pipes |
| 76 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI: 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 77 | Point wiring in PVC conduit, with piano type switch :- wiring for light point/fan point/exhaust fan point/call bell point 1.5 sq.mm FR PVC insulated copper conductor single core cable in existing surface/recessed Steel/PVC conduit including dismantling as required GROUP - B |
| 78 | Twin control Point in PVC conduit with piano type switch :- wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in existing surface/recessed steel/PVC conduit including dismantling as required |
| 79 | Circuit/submain wiring in PVC conduit:-Wiring for circuit/submain wiring along with earth wire with the following size PVC insuleted copper conductor single core cable in recessed PVC conduit as required 2x1.5 sq mm+1x1.5 sq mm earth wire |
| 80 | 2x2.5 sq mm+1x2.5 sq mm earth wire |
| 81 | 2x4.0 sq mm+1x4.0 sq mm earth wire |
| 82 | S/F PVC conduit: supplying and fixing of following sizes PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case recessed conduit as required. 25mm |
| 83 | S/F modular type switch /socket :-Supplying and fixing following modular type switch box/cover including connections but excluding modular plate etc as required 5/6 amps, one way switch |
| 84 | 5/6 amps, 3 pin socket outlet |
| 85 | S/F Modular type electronic fan regulator:-Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connectionons but excluding modular plate etc, as required. |
| 86 | S/F Modular boxes, base & covre plate:-following size/ modular G.I box along with modular base & cover plate for modular switches in recess etc, as required. 1 or 2 module (78mm x 78mm x 45mm) |
| 87 | S/F power plug point with modular type accessories:- Supplying and fixing suitable size G.I.box with modular plate and cover in front on recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular switch conection painting etc, as required. |
| 88 | S/F ceiling rose:-Supplying and fixing 2 pin 5 amp, ceiling rose on the existing junction box/wooden block including connection etc as required. |
| 89 | S/F Batten holder:-Supplying and fixing batten/angle holder including connection etc, as required. |
| 90 | ITC fluorescent fitting directly on surface:-Instaliation, testing and commissioning of prewired, fluorescent fitting of all types, complete with all accessosries and tube etc. directly on ceiling/wall including connection with 1.5 sq mm.FR PVC insulated, copper conductor. |
| 91 | ITC ceiling fan:-Instaliation, testing and commissioning of ceiling fan including wiring the down rod of standard length(uptwo 30 cm) with 1.5 sq mm.FR PVC insulated copper conductor, single core cable etc as required |
| 92 | ITC exhaust fan up to 450 mm, sweep:-Installation of exhaust fan up to 450 mm. sweep in the exiting opening, including making the hole to suit the size of above fan, making good the damage, connection testing commissioning etc as required. |
| 93 | S/F VERTICAL TYPE T.P.MCB DB:-Supplying and fixing following way three pole and nutral, sheet, MCB distribution board,415 volt,in recess, complete with tinned copper busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required. (But without MCB/RCCB/ISOLATOR)Note:- Vertical type MCB TPDB is normally used where three phase outlets are required. 4 way (4+24), Double door, Vertical type |
| 94 | S/F T.P.MCB DB:-Supplying and fixing following way three pole and nutral, sheet, MCB distribution board,415 volt, in recess, complete with tinned copper busbar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and power painted including earthing etc. as required. (But without MCB/RCCB/ISOLATOR) 4 way (4+12), Double door, Horizontal type |
| 95 | 9/10 Watt LED Bulb |
| 96 | 9'' ( 230mm ) metal exhaust fan |
| 97 | S.I.T.C. 1200 mm ( 48'' ) ceiling fan |
| 98 | Add 18% GST (+) |
| 99 | Add 1% Labour Cess (+) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 28, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
TodayOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender