Tender For Miscellaneous Civil Works In Dae Colony, Cisf Complex, And Public Buildings At Nuclear Fuel Complex, Hyderabad.
Tender Value
4.92 Crore
Estimated cost
Bid Submission
06 Nov 2026
5 days left
EMD
9.84 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Medchal Malkajgiri → Telangana
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Miscellaneous Civil Works In Dae Colony, Cisf Complex, And Public Buildings At Nuclear Fuel Complex, Hyderabad.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 23-Oct-2026 | BOQ Corringendum. | BOQ | 06-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | General Notes:1. The contractor shall follow relevant IS codes/technical specifications for execution of work.2. The contractor shall maintain good workman ship and follow safe working procedures during the work.3. Rates are inclusive of Scaffolding for all items for all heights and depths. |
| 2 | Excavation in Trenches/foundation using mechanical/manual means for septic tanks, pipes, sewers, storm water drains, footings etc in all soils except soft and hard rock at all depths from average ground level including dewatering if necessary, dressing bottom to required level, profile/slope, clearing of all the areas involving excavation of all grass,rank vegetation, shrubs,bushes,cutting of trees upto 300mm grith measured at 1.0 mtr above ground level disposing the soil within a distance of 50m, including backfilling complete as directed. |
| 3 | Filling available excavated earth in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, levelling, lead up to 50 m. |
| 4 | Lead charges, including loading, unloading, stacking, the disposable Earth, rock, concrete, brick, debris etc. by mechanical transport for all leads within the DAE colony, CISF complex, public buildings. Note: Measurement of lead charges will be based on truck measurements with deduction of voids @20% and 50% for soils and rocks or debris respectively. |
| 5 | Plain Cement Concrete (P.C.C) 1:3:6 by insitu mixing using Weigh Batching or RMC of grade M-10 using Ordinary Portland Cement(OPC) conforming to IS 269 or Portland Pozzolana Cement (PPC) conforming to IS 1489 Part-1 with Minimum Cementitious Content not less than 250 Kg/Cum (M/s. ACC,Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd. make) with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc., but excluding Formwork, complete as specified and directed. |
| 6 | Reinforced cement concrete of M-30 grade (Minimum Cementations Content not less than 390 Kg/Cum) by insitu mixing using Weigh Batcher or RMC of Ultra Tech, Birla, Ready Mix up to specified level using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer (M/s. Fosroc, Demach, Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications, pumping/ lifting concrete to the required height/depth, consolidation, finishing, curing, etc., complete as per specifications but excluding form work, centering and shuttering and steel reinforcement at all depths/heights below and above floor level. |
| 7 | Providing centering and shuttering using good quality densified film-faced Plywood of at least 12mm thick approved make conforming to IS 4990 so as to produce neat form finished concrete surfaces, with steel staging system formwork including all chamfers, splays, keys, wedges, props, nails, bracings, brackets, tie rods and applying one coat of shuttering oil on all shuttering surfaces in contact with concrete, filling of tie rod holes, wherever required, with non shrink cementitious grout of Forsoc make or approved equivalent, providing PVC/cement mortar cover blocks of adequate strength etc., in foundation, column, flooring, machine foundation, piller, post,struts, sofits of beam, beam haunching, lintel, cantilever, girder, walls partition wall, sofits of cantilever suspended floors,landings, balconies,chajjas, Slab etc.complete as directed by EIC. |
| 8 | Supply, fabrication and erection of Reinforcement bars for Reinforced cement concrete items at all depths and heights below and above plinth level Thermo-Mechanically Treated bars of minimum grade Fe-500D/550D or more conforming to IS 1786 of Tata, Vizag steel, Sail, JSW, JSPL make, including transport to site, loading and unloading, making fan hooks of required shape, dowels for bonding masonry, transporting steel to site, decoiling, removing of scales, straightening, cutting, bending, fixing bars with chairs, space bars wherever required, in position with two strings of 18 gauge soft drawn annealed MS binding wire inclusive of its supply etc., providing cement mortar cover blocks of adequate strength, complete as specified and as per direction of Engineer- in-Charge. Note: The grade of reinforcedment bars shall be gotten approved by EIC before procurement. |
| 9 | Providing and laying autoclaved aerated cement blocks masonry with 150/230/300 mm thick or other required size Grade-I AAC blocks of density 551 to 650 Kg/cum conforming to IS 2185 (Part 3) of make M/s NCL, Aerocon, Greenstone in super structure below and above plinth level up to floor V level with approved block laying polymer modified adhesive mortar or in cement mortar 1:4 (1 cement : 4 coarse sand), complete as directed. |
| 10 | Brick work as per IS 2212 using fly ash bricks conforming to IS 12894 of Class Designation 7.5 and above as specified at all height and depths with cement mortar 1:6 {1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP) : 6 crushed Sand} including raking out joints and simultaneously pointing the joints with the same mortar, curing, scaffolding etc., complete as specified and directed. |
| 11 | HALF BRICK masonry as per IS 2212 using fly ash bricks conforming to IS 12894 of class designation 7.5 or above as specified in partitions walls in cement mortar 1:4 (1 cement: 4 crushed sand), including scaffolding, raking out joints, curing etc. complete and with Reinforced Cement Concrete (RCC) M15 (1:2:4) stiffeners of depth 75mm at every 900 mm height including form work, curing etc., complete as specified and directed, but excluding reinforcement. Note: Reinforcement will be measured and paid for separately under relevant item of schedule.-above plinth level up to 5th floor |
| 12 | Random rubble/Coursed rubble masonry in Cement mortar 1:6 (1 cement : 6 coarse sand) with hard stone in below and above plinth level up to 5th floor with sized stone of required size and shape, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) complete as specified and directed. |
| 13 | Repairs to plaster of thickness 12 mm to 20 mm in patches by Polymer modified plaster including cutting the patch in proper shape, raking out joints and preparing and plastering the surface by removing the reinforcment rust by rust remover and applying a coat of corrosion resistance chemical and also applied a single coat of epocy bonding agent before applying polymer modified plaster complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge |
| 14 | Cement plastering 15 mm thick for internal walls using ready made plaster in cement mortar (1cement:4 Sand) of make M/s Enduraplast, Walplast, Ultratech or approved equivalent fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC , providing & fixing GI plaster mesh/chicken mesh 150 mm wide along route of walls chipped for service lines, junction between RCC and brick walls and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed. |
| 15 | Cement plastering 20mm thick in Two (2) coats over exterior masonry and concrete surfaces at and at all heights/depths above/below plinth level using ready mixed plaster of make M/s Enduraplast, Walplast, Ultratech or approved equivalent with 12mm thick base coat in Cement Mortar 1:4, 8mm thick finishing coat in Cement Mortar 1:4 , final rendering, making necessary grooves, bands, drip moulds, providing & fixing GI plaster mesh/chicken mesh 150 mm wide along route of walls chipped for service lines, junction between RCC and brick walls and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed. |
| 16 | Providing and applying white cement based putty in two coats including providing one coat of primer with average thickness of not less than 1 mm, of Birla make or any other approved manufacturer over the plastered/painted wall surface (external/internal) including cleaning the surface, surface preparation, rubbing with sand paper before putty, scraping of the existing loose paint with putty knife, filling of holes with putty, filling of cracks with fosroc renderoc CF/CS or approved equivalent, preparing the surface even and smooth complete for all heights, complete as specified and directed by EIC. |
| 17 | INTERNAL PAINTING:- Supplying and applying two or more coats of interior luxury emulsion paint with high sheen, stain resistant and antibacterial/antifungal properties of make Asian (Royal advanced/sheen luxury emulsion) or approved equivalent including providing one coat of approved suitable interior primer at all heights above plinth level, including cleaning the surface, surface preparation, rubbing with sand paper, scraping of the existing loose paint with putty knife, filling of holes with putty, filling of cracks with fosroc renderoc CF/CS or approved equivalent, complete and as directed. |
| 18 | EXTERIOR PAINTING :- Applying of Two or more coat of elastomeric liquid applied water proofing membrane of asain paint damp proof advance or Dulux Aquatech Flexible damp proof base coat as per manufacture specification.Finishing walls with 2 or more coat of 100% Premium acrylic Smooth waterproof exterior finish emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS:15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Dept Tinted) with silicon additives, equal to asain paint ultmia protek or Dulux Professional weathershield Flexx or Paints can be obtained from approved make from M/s. Asian, Dulux, Berger, Johnson & Nicklson, Nerolac, Pidilite or any other make etc., including surface preparation, scrubbing, sand papering, removing of loose paint, plaster, dirt, etc., filling of cracks, holes with crack filler of make fosroc renderoc CS/CF or approved equivalent complete and as directed. |
| 19 | Painting with synthetic enamel paint in 3 ( three ) coats including a coat of appropriate primerof Asian/Berger/Nerolac make of 1st quality with required shade on walls, concrete surfaces, wooden/steel doors, windows, ventilators, composite units, louvers, rolling shutters, hand rail and balustrades, plastered surfaces etc., including scaffolding, preparing the existing surface smooth by sand papering, preparing the surface, brushing with wire brushes, scraping with steel scrapper etc., filling in crevices and cracks etc. with approved filler etc., complete as specified and directed. |
| 20 | Removing old paint by using scrubbing machine, chemical method, preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 21 | Distempering with 1st quality acrylic distemper ( ready mixed ) having VOC content less than 50 gram/litre, of approved brand and maufacture of Asain, Dulux, Berger or any equivalent including surface preparation,applying additional coats wherever required filling the holes and cracks with fosroc renderoc CF/CS or approved equivalent and cleaning the old surface to achieve even shade and colour- Old Work ( One or More Coats) to get the even surface. |
| 22 | Demolishing plain cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as specified and directed including disposal of debris up to 2 KM. |
| 23 | Demolishing R.C.C. work manually/ by mechanical means including cutting, stacking of steel bars and disposal of unserviceable material within 50 metres lead including disposal of debris up to 2 KM. as per direction of Engineer - in- charge. |
| 24 | Dismantling very carefully the existing Brick masonry in cement motor with plastering on both sides including wall tiles, old pipelines if any very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacking of useful materials and disposing the unserviceable debris within the lead of 50m, including disposal of debris up to 2 KM. etc., complete as specified and directed. |
| 25 | Dismantling existing wooden / M.S/PVC/Al. (or other material) doors, windows, ventilatiors etc., including shutters, frames, holdfasts etc very carefully without damaging the frame and shutter etc., disposing the unserviceable materials within a lead of 100m including disposal of debris up to 2 KM. completed as directed by Engineer-in-Charge. |
| 26 | Debit for buyback of dismantled MS/Wooden/Aluminium/Plastic Windows/Doors/Partitons along with glass, door/window frames (Opening Size will be measured for payment) by the contractor. |
| 27 | Dismantling the existing mosaic tiles / glazed tiles ceramic tiles / vitrified tiles / shahabad stone etc., in flooring / dado including dismantling, bedding mortar and disposing the debris within 50 m lead including disposal of debris up to 2 KM. as directed by Engineer-in-Charge. |
| 28 | Dismantling old plaster, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 including disposal of debris up to 2 KM. metres lead |
| 29 | Dismantling of old IWC/EWC and \\"S\\" or \\"P\\" trap at site including removal of cistern if required, complete with disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge |
| 30 | Providing, laying, jointing, fixing, testing and painting as per color code of NFC heavy quality (Class ‘C’) M. S. GALVANISED PIPES as per IS:1239 (TATA/Jindal or equivalent make) including heavy quality HB fittings like elbows, collars, tees, unions, couplings, reducers, enlargers, bends and all other fittings required for the completion except screwed flanges confirming to IS:1239 and also as per the code of practice of water supply in buildings IS:2065 including removing of exisitng G.I. pipes and fixtures if any, laying under the floors, making holes/chasing in walls, roof slabs and making good the same to the original condition including cost of all jointing material like hemp yarn, white or red lead/Teflon tape, clamps, wooden gutties, screws, cement and painting with two coats of anticorrosive bitumastic paint for embedded portion and two coats of synthetic enamel paint over a coat of zinc chromate/red oxide primer etc., complete including pressure testing the pipes with clean water as per specifications and connecting to existing supply lines or fittings and fixtures as the case may be. |
| 31 | 20 mm n. b. |
| 32 | 25 mm n. b. |
| 33 | 40 mm n. b. |
| 34 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11) conforming to IS 15778 of Ashirvad/Supreme or approved make, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, MABT, FABT, fittings required for making connection with existing GI/CPVC line etc., i/c fixing the pipe on exposed/recessed/underground surfaces to correct line, level, plumb using clamps as directed. This includes removing of existing pipes and fixtures/CP fittings if required, jointing of pipes & fittings with one step CPVC solvent cement, teflon tape, cost of making holes/ cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition including testing of joints at certain locations complete as specified and directed |
| 35 | 20mm dia |
| 36 | 25mm dia |
| 37 | 40mm dia |
| 38 | Providing and fixing in position CPVC ball valves of following sizes of Ashirvad/Supreme make confirming to SDR 11 fittings, including jointing material etc, as specified and directed. |
| 39 | 20 mm DN |
| 40 | 25 mm DN |
| 41 | 40 mm DN |
| 42 | Supplying and fixing following size pushfit/solfit uPVC UV-Stabilised soil / waste/rain water pipes (conforming to IS 13592) and fittings (conforming to IS 14735) of Grade B laid in floor, underground, concealed & on exposed faces of wall of Ashirvad/Supreme make, including scaffolding, removal of existing pipelines if any, laying the pipe below floor / ground to proper slope and gradient, cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases in RCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original condition, jointing the pipe with Solvent Cement/Rubber ring gasket, ensuring water-tightness for the pipes laid as per codal provisions, cutting to the required length including short pieces, fittings with & without door, fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, cleaning pipe, single & double Y, vent cowl, gaskets, offsets, Tank / WC connectors, cowls, clamps, etc, complete as specified and directed. |
| 43 | 50 mm DN |
| 44 | 75 mm DN |
| 45 | 110 mm DN |
| 46 | Providing uPVC Floor Trap / Nahani Trap of following size conforming to IS 14735 with CP jalli on top, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer's recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient, closing the side inlets with plugs if required etc. all complete as specified and as directed |
| 47 | Nahani Trap of 110 X 75mm size of Ashirvad (70001249)/Supreme make |
| 48 | Multifloor trap of 110 x 75 x 50 mm size of Ashirvad (70001252)/Supreme make |
| 49 | Providing and fixing of best quality PVC P trap for urinals of size 110mm X 110mm of Ashirvad (70002811)/Supreme make or approved equivalent with CP grating on top including necessary 1:2:4 cement concrete for embedding the trap connecting the trap to waste pipe, etc, complete as specified and directed. |
| 50 | Providing and fixing in position UPVC bottle Gully Trap of Supreme /Ashirvad make of 160 X 110mm sizes including embedding the trap in 1:2:4 cement concrete, construction of brick masonry chamber in 230 mm thick brick masonry in cement mortar 1:4 over cement concrete bed of 1:3:6 of 100 mm thick, embedding the trap, plastering with cement mortar 1:4, 12 mm thick on inside & outside and all exposed surfaces, finished with a floating coat of neat cement, providing and fixing heavy duty C. I. frame and cover of size 300mmX300mm, 40mm thick cement concrete 1:2:4 bed over brickwork, painting the grating frame and cover with 2 coats of approved anticorrosive bitumastic paint, necessary connection with existing line etc., complete as directed. |
| 51 | Providing & laying structured wall UPVC under ground drainage pipes & fittings (SN-8) of Ashirvad/Supreme make for sewer lines of following size conforming to IS:16098 (Part-1) to proper level & grade, jointing including providing coupler with cement solvent / welded joints / as per manufacturer's requirement, UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc, connecting with existing manholes, including making holes in manholes and grouting with GP2 grout after fixing of pipe, complete as specified and directed by EIC. |
| 52 | 110 mm DN |
| 53 | 160 mm DN |
| 54 | Providing and fixing EUROPEAN WATER CLOSET of size close to the dimensions 575 x 355 x 395 mm of Hindware (20147 (S-100) or 20146 (P-180))/ Jaquar or approved equivalent , in white glazed vitreous, with integral 'P' or 'S' trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making good floor, wall wherever required, as specified and directed |
| 55 | Providing and fixing one piece EUROPEAN WATER CLOSET of Hindware(Cat no. 20190)/Jaquar make or approved equivalent , in white glazed vitreous, with integral 'P' or 'S' trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making good floor/ wall wherever required including the cost of mounting nuts and bolts with washers. |
| 56 | Providing and fixing approved ORRISA PATTERN W.C. of soze close to 580mm X 440mm of Hindware(Cat no. 20042)/Jaquar make or approved equivalent in white glazed vitreous chinaware, size mm with 'P' or 'S' trap, conforming to IS: 2556. |
| 57 | Providing and fixing single flush PVC low level flushing cistern of 10 litres capacity conforming to IS: 7231 of Jaquar/Hindware(Cat no. 511209) make or approved equivalent with all internal PVC fittings mounted on a pair of brackets of heavy quality with 32 mm n. b. PVC flush pipe with bend of required length with all tools, synthetic adhesive, gasket etc., complete including connection to W. C. |
| 58 | Providing and fixing in toilets Health faucet of Hindware/Jaquar (ALD-CHR-573) make or equivalent with 1.2 meter long flexible tube or as per manufacturer's specifications in Chrome finish and wall hook etc. complete as directed.. |
| 59 | Providing and fixing 15 mm n. b. heavy quality PVC connector pipe suitable for hot and cold water for Cisterns, Wash basins, gyesers, urinals of suitable length with CP brass unions ends of ZOLOTO/HINDWARE/JAQUAR make. |
| 60 | Providing and fixing URINAL of size close to 385 mm x 325 mm x 635 mm of M/s.Jaquar(URS-WHT-13253N) /Hindware make or approved equivalent screwed to wall/dado with full threaded C.P. brass waste coupling to urinal, spreader, drain pipe etc. removing the existing urinal if required, complete as specified. |
| 61 | Providing and fixing 32/40 mm n. b. C. P. brass single flush valve for urinal along with wall flange/plate of make Jaquar (PRS-CHR-073)/hindware or equivalent and other required accessories/fittings, including making recess in wall, flush pipe and connecting the valve with concealed water supply pipe and urinal. |
| 62 | Providing and fixing in position of best quality curved shaped urinal PARTITION with frosted glass (8mm thick) of size 450mmX900MM of Jaquar (JSE-CHR-810UC450X)/Hindware make or approved equivalent, including removing of existing partition if required as directed by Engineer-in-charge. |
| 63 | Providing and fixing best quality stainless steel matt finished kitchen WASH BASIN of size 610 mm x 460 mm x 200 mm of Hindware or approved equivalent make with C.I. brackets and waste coupling including painting of fittings and brackets, cutting and making good the walls wherever required |
| 64 | Providing and fixing best quality WASH BASIN of size 500mm X 400 mm, comprising best Indian make (Hindware (Cat no 10127)/Jaquer or approved equivalent wash basin white glazed, vitreous chinaware conforming to IS: 2556 Part IV supported on suitable wall brackets of heavy quality and of size mentioned above, including CP brass waste coupling, removing of existing wash basin if required as directed by Engineer-in-charge. |
| 65 | Providing and fixing best quality vitreous chinaware under the counter WASH BASIN of size close to 605mm x 430 mm x 200mm , of make Jaquar (CNS-WHT-705)/ Hindware make or approved equivalent conforming to IS: 2556 Part IV including CP brass waste coupling, necessary supports, removal of wxisting wash basin if required, complete as specified and directed. |
| 66 | Providing and fixing CP Brass 32mm size heavy quality Bottle Trap of approved quality & make Jaquar (ALD-CHR-769L)/ Hindware or approved equivalent, inluding extension pipe if required, removal of existing bottle trap if required, as per the direction of Engineer-in-charge. |
| 67 | Providing and fixing heavy quality half threaded/full threaded C. P. brass waste coupling of size 32mm of make Jaquar/Hindware or approved make. |
| 68 | Providing and fixing 32mm/40mm dia flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 69 | Providing and fixing heavy quality 15 mm C. P. brass Long body BIB TAPS of Hindware(F730011CP)/Jaquar make or approved equivalent with wall flange and confirming to IS:8931. |
| 70 | Providing and fixing heavy quality 15 mm C. P. brass Pillar cock of Jaquar /Hindware make (F730002CP) or approved equivalent confirming to IS:8931. |
| 71 | Providing and fixing heavy quality 15 mm C. P. brass E Sensor Tap of Jaquar/Hindware make (Cat no. F240003CP) or approved equivalent. |
| 72 | Providing and fixing heavy quality 15 mm C. P. brass 2 way bib cock of Jaquar/Hindware make (F730054CP) or approved equivalent with wall flange and confirming to IS:8931. |
| 73 | Providing and fixing 15 mm n. b. heavy quality C. P. brass angle valve confirming to IS 8931 of make hindware (F730039CP)/Jaquar or approved equivalent. |
| 74 | Providing and fixing 15 mm n. b. heavy quality C. P. brass Push Type urinal angle valve confirming to IS 8931 of make Jaquar/hindware (F310016) or approved equivalent. |
| 75 | Providing and fixing heavy quality 15 mm C. P. brass Concealed stop cock consisting exposed part kit of Jaquar /Hindware (Cat no F730013CP) make along with heavy duty concealed stop cock body of Jaquar/Hindware (F850096CP) or approved equivalent with wall flange and confirming to IS:8931. |
| 76 | Providing and fixing heavy quality 15 mm C. P. brass Non Telephonic wall mixer of Jaquar /Hindware(F730016CP) or approved equivalent including wall flange and confirming to IS:8931. |
| 77 | Providing and fixing heavy quality 15 mm C. P. brass 3 in 1 wall mixer of Hindware(F730020CP)/Jaquar or approved equivalent including wall flange and confirming to IS:8931. |
| 78 | Providing and fixing heavy quality 15 mm C. P. brass Deck Mounted Sink Cock of Hindware make (F730034CP)/Jaquar or approved equivalent confirming to IS:8931. |
| 79 | Providing and fixing decorative round shaped C. P. brass SHOWER ROSE of dia 200mm without arm of make Jaquar/ Hindware(F160125) or approved equivalent |
| 80 | Providing and fixing decorative round shaped C. P. brass long shower arm of 450mm length of make Jaquar/ Hindware (F160024) or approved equivalent |
| 81 | Providing and fixing C. P. brass TOWEL RAIL of approved design and make of 600mm length, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Hindware (F880005CP)/Jaquar or approved equivalent. |
| 82 | Providing and fixing CP brass geometric soap dish of make hindware (F580004CP) /Jaquar or equivalent. |
| 83 | Providing and fixing CP brass Toilet Paper Roll Holder with cover of Hindware (F880003CP)/ Jaquar or approved equivalent as specified and directed. |
| 84 | Providing and fixing C. P. brass Twin Robe Hook, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Hindware (F880004CP)/Jaquar or approved equivalent. |
| 85 | Providing and fixing SS 304 Cloth Hanger with four hooks, fixed to wall or doors with C. P. brass screws, screwed on to rawl plugs etc., complete as directed by Emgineer-in-charge. |
| 86 | Providing and fixing 5-6 mm mirror of superior glass (of approved quality modi guard) complete. The mirror to be fixed by silicon or any other approved material required to fix mirror on the wall as specified and directed by EIC. |
| 87 | Supplying of following items to the EMS store as per the direction of Engineer-in-charge |
| 88 | Supplying of PTMT Bip Tap of Prayag in standard series 121-O or equivalent |
| 89 | Supplying of PTMT pillar cock of Prayag in standard series 130-O or equivalent |
| 90 | Supplying of PTMT Stop Cock of Prayag in standard series male/Female.or equivalent 141-W |
| 91 | Supplying of PTMT Angle Cock of Prayag in standard series 144-O or equivalent |
| 92 | Supply of PTMT Two Way Bip Tap of Prayag in standard series 129-O or equivalent |
| 93 | Supplying Flexible (coil shaped) PVC waste pipe for sink and wash basin 32mm/40mm dia with length not less than 700 mm i/c PVC waste fittings |
| 94 | Supplying of 15 mm PVC connector pipe suitable for hot and cold water make Zoloto/Kohinoor-24 inch length |
| 95 | Supplying of CPVC tank Nipple of 1 inch size |
| 96 | Supplying of EWC seatcover M/s Hindware or equivalent |
| 97 | Supplying of 59 ML CPVC solvent Tube/tin as and when required. |
| 98 | Supplying of 110 mm CP Grating ( Plain / Hole) |
| 99 | Supply of 3 mtr length 25 dia SDR-11 CPVC pipe of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 100 | Supply of CPVC Brass Bush/ Reducer 25X20 of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 101 | Supply of CPVC Bush/ Reducer 25X20 of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 102 | Supply of 25mm CPVC elbow of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 103 | Supply of 25mm CPVC Tee of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 104 | Supply of 25mm CPVC Coupling of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 105 | Supply of 25mm CPVC 45 Degree elbow of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 106 | Supply of 25mm CPVC Ball Valve of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 107 | Supply of 20 X15 mm CPVC Brass elbow of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 108 | Supply of 20 X15 mm CPVC Brass MTA/FTA of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 109 | Supply of 20 X15 mm CPVC Brass reducer coupling of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 110 | Supply of 25/20 mm CPVC end cap of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 111 | Supply of 15 mm PVC Threaded Plug of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 112 | Supply of 25/20 mm CPVC Tank Nipple of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 113 | Supply of Sintex Tank Cover/Led suitable for 750Litre/1000 Lite Tank |
| 114 | Supply of 20 PTMT Float valve of of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 115 | Supply of 25 PTMT Float valve of of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 116 | Supply of 40 PTMT Float valve of of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 117 | Supply of 50 PTMT Float valve of of Astral/Ashirwad/Sudhakar/Prayag or equivalent |
| 118 | Supply of PVC waste coupling of Prayag Cat no 102/Ashirwad or equivalent |
| 119 | Supply of CP Bip tap of Prayag Make Cat No 8302 or equivalent |
| 120 | Supply of CP pillar cock with flange Prayag make No 6802or equivalent |
| 121 | Supply of CP Angle cock with flange Prayag make No 8310 or equivalent |
| 122 | Supply of CP Two Way bip Cock with flange Prayag make No 8311 or equivalent |
| 123 | Supply of CP waste coupling of Prayag Make No BEA-11s or equivalent |
| 124 | Supply of CP SS tube Health Faucets prayag Make BEA-40 or equivalent |
| 125 | Suppling of 8X3 feet single side laminated WPC door of M/s Rajshree or approved equivalent of Density not less than 650 Kg/cum.-28 to 30 mm thick |
| 126 | Supply of 8X3 feet WPC sheet of Min density of 650kg/m3 of m/s Rajshree and equivalent-6 mm thick |
| 127 | Supplying of 15 mm brass spindle for taps, quater or half turn as per requirement. |
| 128 | Supplying of 15 mm brass spindle for taps, full turn as per requirement. |
| 129 | Supplying of 32 mm PVC IWC long bend |
| 130 | Supplying of SS matt fininsh door stopper ( Top Operated) of M/s Harwin, M/s kich |
| 131 | Supplying of MS peg style Handle |
| 132 | supply of Wooden beading of 1/2\\" inch X 1/2\\" inch |
| 133 | supply of Z section Steel Window Lock Handle |
| 134 | Supply of Nickel Star Hook of Size (6x19) each box contain 1000 Nos |
| 135 | Supply of Nickel Star Hook of Size (6x25) each box contain 1000 Nos |
| 136 | Supply of Nickel Star Hook of Size ( 8x19) each box contain 1000 Nos |
| 137 | Supply of Nickel Star Hook of Size (8x25) each box contain 1000 Nos |
| 138 | Supply of Nickel Star Hook of Size (8x38) each box contain 500 Nos |
| 139 | Supply of Nickel Star Hook of Size (8x75 ) each box contain 200 Nos |
| 140 | Supply SS nut and bolt 6X 50 mm |
| 141 | Supply of wooden cutting blade 4\\" or 5\\" |
| 142 | Supply of crome plated Hand Towel rail Of Min 750 length of Parriware ( T6001 A1) or hindware |
| 143 | Supply of Stainless Steel grade 304 mosquito proof mesh with 0.4 mm dia. wire and 1mm wide aperture. |
| 144 | Supply of Chop saw of make Bosch PRO GCO 220 make |
| 145 | Supply of 18V-8 cordless angle grinder of make Bosch PRO GWS |
| 146 | Supply of cordless screw driver of make Bosch PRO GSB 185-Li |
| 147 | Supply of 18V, 4 AH battery pack of make Bosch BV PRO GBA |
| 148 | Providing & fixing glazed vitrified tiles/double charge vitrified tiles of polished/digital printed/matte/anti-skid/rustic finish of size 600mmX600mm/1200mmX600mm/800mmX800mm and thickness as per manufacturer's specifications conforming to IS 15622 for flooring ( thickness as specified by manufacturer) of make Johnson, Somani, Kazaria, RAK of required shade, design, colour and pattern laid on 20 mm thick cement mortar 1:4 (1 cement (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd.): 4 coarse sand) or polymer modified adhesive of make MYK/Roff or approved equivalent including providing joints of 2mm/3mm with spacers filled with epoxy grout mix of 0.7 kg of organic coated filler of desired shade and matching pigment (0.1 Kg of hardener and 0.2 Kg of resin per kg or as specified by manufacturer ) of make Pidilite, MYK of required color. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 149 | Providing & fixing glazed vitrified tiles/double charge vitrified tiles of polished/digital printed/matte/anti-skid/rustic finish of size 600mmX600mm/ 1200mmX600mm/ 800mmX800mm/ 300mmX600mm and thickness as per manufacturer's specifications for dado, skirting, risers of steps, etc (thickness as specified by manufacturer) of make Johnson, Somani, Kazaria, RAK of required shade, design, colour and pattern laid using suitable high polymer modified quick-set tile adhesives (Water based) of Roff/MYK or approved equivalent, providing joints of 2mm/3mm with spacers, filling of joints with matching epoxy grout mix of 0.7 kg of organic coated filler of desired shade and matching pigment (0.1 Kg of hardener and 0.2 Kg of resin per kg or as specified by manufacturer ) of make MYK, pidilite of required color, as required, complete as specified and directed. |
| 150 | Grouting the joints of flooring/dado/skirting tiles having joints of 2mm/3 mm width, using epoxy grout mix of 0.70kg of organic coated filler of desired shade and matching pigment (0.10 kg of hardener and 0.20 kg of resin per kg or as specified by manufacturer), including filling / grouting and finishing, removal of existing grout in the joints, complete as per direction of Engineer-in-charge |
| 151 | Providing and fixing 16 to18 mm thick gang saw cut, mirror polished, premoulded and prepolished /honed /leathered/ lappato or in combination machine cut Granite stone for floor/treads/ risers /steps / dado/ ramps/window sills/jambs/wash basin platforms/ fascias/ door chowkhats etc. of required size, approved shade, colour and texture laid over minimum 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse crushed stone sand)/ 12 mm thick, 1:3 (1 cement : 3 coarse crushed stone sand) cement mortar/chemical adhesive, joints treated with epoxy grout, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish, mitring, making cutouts in granite for washbasin/pillar taps/any other fittings etc. complete at all levels including cost of single/double nosing, making 3 no of grooves for saircase treads etc. all complete as specified and as directed.Note: 1) The rate shall be including of making necessary holes/cut outs in granite for sink, PH fittings, door lock etc. wherever required.2) Single piece granite of required size as directed by EIC shall be used for steps, window sills/jambs, door chowkhats, kitchen sink etc. No extra payment will be made for the same. |
| 152 | Providing and fixing factory made single extruded WPC ( Wood polymer Composite ) solid with both side PVC laminated/Marble PVC Sheets/PVC foil flush door shutter of required sizes and following thickness comprising of virgin PVC polymer of K value 58-60 ( Suspension Grade ), calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) having minimum frame density of 650kg/cum , screw withdrawal strength of 1800N (Face ) & 900 N ( Edge ) , Modulus of Elasticity 900 N/mm2 and resistance to spread of flame of Class A Category with property of being termite/borer proof, water / moisture proof and fire retardent, including providing and fixing necessary stainless steel door fittings (including necessary accessories, hardware, screws etc.) of make Kich/Godrej or approved equivalent viz. stainless steel butt hinges (with or without ball bearings) of required size (3 nos of size 5 inches and 3mm thickness) with neccessary full body threaded star headed counter sunk S.S Screws, Stainless steel aldrops, SS tower bolts/latches/baby latches, SS door stopper, SS both sides door pull handles ('C' or 'H' shaped) if and wherever required for each door, complete as per direction of Engineer in Charge. |
| 153 | 28mm to 30 mm solid WPC flush door shutter ( laminated both side) |
| 154 | 35mm solid WPC flush door shutter ( laminated both side) |
| 155 | Supplying & fixing in position minimum 30mm thick non-decorative single/double leave solid core block board flush door shutters of appropriate size conforming to IS 2202 (latest) of M/s Raavela, Elegant Kalpataru, Anand, Kutty or approved equivalent with external type second class teak wood lipping alround, including fixing shutters in position to pressed steel door frames/wooden frames/granite frame works (door frames shall be paid separately under relevant item) at all floors by cutting / planing if necessary (excluding the cost of fittings and fixtures with screws which shall be paid separately under relevant item) including making of grooves on both sides of shutters in laminate/veneer as per the drawing/design, painting the edges of shutters with two coats of wooden varnish if required of approved make & colour over one coat of approved primer etc. all complete as per specifications,drawings & as directed by Engineer in charge. NOTE : Decorative synthetic laminate shall be paid under relevant item. |
| 156 | DOOR FRAME WORK:- Supplying and fixing of door frame made of 12mm thk/19mm thick BWP grade plywood conforming to IS 303 BWP grade or IS 710 BWP grade, of approved make 100% Gurjan Brand Royal Club/Gurjan club/Century/Green Ply or approved equivalent etc. in proper line and level with Laminate/Veneer finish of approved make GreenLam/Century or approved equivalent of approved shade, fixing 19mm thick ply to masonry wall/column by all means of approved wooden screws/ nails/fastners, fixing the 12mm ply over the 19mm ply for making the door rebate, fixing of 12mm/19mm ply on the top and sides of door opening on both sides upto 100mm width, cutting the ply and fixing with nails/ metallic wooden screws in line, fixing the ply/laminate with approved suitable adhesive of make pidilite (fevicol marine/Hi-per/heatex/Probond) or approved equivalent complete as directed and specified.Note: 1) The ply used shall be of minimum 25 years warranty.2) The rebate will not be measured for payment.3) The height will only be measured from inside the door opening and entire width of the door frame (including the ply fixed on sides and top of door opening) will be measured for payment.4) Any extra ply if required for line and leveling/installation of fixtures/door closers/door handles shall be provided at site as per site conditions without any extra cost.5) The laminate/veneer will be paid in relevant item. |
| 157 | Providing and fixing Heavy quality Stainless Steel of grade SS304 butt hinges with or without ball bearings for wooden doors of size 125mm length and 3mm thickness of make kich / Godrej or approved equivalent with necessary screws etc complete as directed. |
| 158 | Providing & fixing stainless steel of grade SS304 square tower bolts for wooden doors of min size 200 X10mm size of make Kich (TBS38S) or approved equivalent with necessary screws complete as specified and directed . |
| 159 | Providing & fixing set of stainless steel of grade SS316 mortice door Handles for wooden doors of dia 22 mm, including set of escutcheons of make Kich (MH223FS), necessary screws etc, complete as specified and directed . |
| 160 | Providing and fixing 9 inches mortise door lock of size 60mmX85mm with SS finish without mortice handles for wooden doors with main plate and strike plate of make Kich(MLB94S) or approved equivalent and mortice pin cylinder with one side knob/slot/key and other side knob/slot/key of make Kich (PCSNS60) or approved equivalent, or latch lock/rim lock with cover plate for double door including necessary screws etc., complete as specified and directed. |
| 161 | Providing & fixing set of stainless steel of grade SS316 door pull Handles for wooden doors of size 22mmX250mmX350mm of make Kich (PHH2510S), necessary screws etc, complete as specified and directed . |
| 162 | Providing and fixing stainless steel (SS304) hanging floor Door stopper for wooden doors with double door buffer of make Kich (PRDB32DS) or approved equivalent, necessary screws etc. complete as specified and directed. |
| 163 | Providing and fixing stainless steel over head door closer of Kich (DC512SS) make or approved equivalent for wooden doors weighing upto 90kg with necessary accessories, fixtures, fittings, scews etc, complete as specified and directed. |
| 164 | Providing and mixing integral crystalline admixture of M/s Pidilite/Fosroc/Cika/BASF make for water proofing tretament to RCC structures at the time of transporting of concrete into the drum of RMC truck, as per manufacturer's specifications. The material shall meet the requirement as specified in ACI-212-3R-2010 i.e. by reducing the permeability of concrete by more than 90%, compared with control concrete as per DIN 1048. The crystalline admixture shall be capable of self-healing of cracks upto a width of 0.5mm. The work shall be carried out all complete as per specifications and the direction of Engineer-in-charge. |
| 165 | Providing water proofing treatment for terraces with cold applied, Acrylic and Poyurethane hybrid Elastomeric liquid membrane coating over one coat of crystallization coating system Pidilite / Fosroc / Cica in the following sequence: a) Cleaning the surfaces from dirt, dust and other contaminations b) Identifying the areas of leakage by approved means, c) Pressure grouting the area of leakage with cement slurry admixed with expansive grouting additive of M/s. Fosroc / Pidilite (Dr FIxit Pidicrete AM) or its approved equivalent at a minimum one grout point per 2 Sq.m slab area.or as per site conditions) (d) Exposing, cleaning, making of v-groove and filling cracks observed if any in RCC slab with polymer modified mortar compound/ PU sealent.e) Pre wetting the surface of slab and application of one coat of crystallization coating of M/s Fosroc/Pdilite (Dr Fixit Polypus CP) or approved equivalent f) Applying one coat of primer of M/s Fosroc/Pdiite (Dr. fixit primeseal) or approved equivalent g) Apply first coat of acrylic and PU hybrid elastomeric liquid membrane coating of M/s Fosroc/Pdilite (Dr. FIxit Roofseal Ultra) or its approved equivalent h) Laying of 45 GSM Fiber glass mesh incorporated in the coating as a sandwich layer when the first coat is still inwet condition i) Apply second/third coat of acrylic and PU hybrid elastomeric coating of make Dr. Fixit Roofseal Ultra all as per approved manufacturer’s specifications and as directed by Engineer in Charge.Note: The treatment shall be carried out for edge termination, cut-outs, pipes/cables penetrations, Bore packing, sleeves, drainage, wall/column and slab junctions, etc. using thermoplastic elastomeric tapes, non shrink cementitious grout, SBR polymer modified mortar or other suitable means wherever required as directed by EIC at no extra cost. |
| 166 | Providing and applying Water pproofing treatment for bathrooms, water closets etc. using ultra flexible polymer modified elastomeric waterproof coating, brick bats and cement based waterproofing in followng steps: |
| 167 | Providing and applying Ultra flexible polymer modified elastomeric waterproof coating for bathrooms using Brushbond Ultraflex of Fosroc Chemicals or approved equivalent in following steps:Surface preparation: RCC surface shall be made dry, clean, even and checked for soundness. Oil, dirt, laitance and other contaminants shall be removed manually.Surface shall be fairly smooth finished using polymer modified mortar. Chamfering of the floor wall junctions shall be done with cement mortar 1:4 admixed with Nitobond SBR @ 2 litres per 50 kg bag of cement. Inlet Outlet Pipe Annular space packing shall be done using Conbextra GP2 of Fosroc Chemicals mixed water in ratio 0.16. Pond testing shall be done for 48 hours, 50mm height and leaking spots, construction joints and honey combs shall be provided with Injection grouting using cementitious pressure grouting method with 40 psi pump using Cebex 100 of Fosroc Chemicals @ 225gms mixed to 50 kg bag of cement including joints packing using polymer modified mortar complete as per manufacturer's specification or as directed by EIC. Waterproof Coating: Apply Ultra flexible polymer modified elastomeric waterproof coating of 1mm thickness in 2 coats at a coverage rate of 16 sqm per 25 kg bag with interval period of 6 hours over a substrate with Saturated Surface Dry condition. Termination to be done on wall extending the coating to min.300mm height above the finished floor level and sealed in the termination groove of 20mm wide and 10mm deep flushed with polymer modified mortar as per manufacturer's recommendation or as directed by EICSupplying and sprinkling of Fine sand while the polymer modified elastomeric waterproof coating is in tacky condition. Providing and laying plastering of 18mm thickness for floors and 12mm thickness for walls in CM 1:4 mixed with integral waterproofing compound Conplast WL Xtra @ 200ml per bag of cement. System include necessary preparation, curing with water, chemicals used, labour, etc as per specification complete before providing screed concrete / brick bat coba / cinder filling. |
| 168 | Providing water proof brick bat coba with cement mortar 1:5 admixed with water proofing chemical of Fosroc/Pidilite or approved make for filling in the depressed portions of toilets, bath rooms etc., as per the specifications of specialized waterproofing agencies and finishing the top surface with 1:4 cement mortar mixed with water proofing chemical so as to be suitable to receive the tiles etc. testing the treatment for water tightness by impounding water for 7 days etc., complete. |
| 169 | Providing cement based waterproofing treatment to the sunken floor of water closets, bath rooms, nahanis from inside at all heights above plinth level giving injections to the concrete surface as required with cement and approved waterproofing compound of Fosroc(Conplast WL Xtra @ 200ml per bag of cement)/Pidilite or approved equivalent to fill up all inherent holes, voids, honey-combs, etc., in the concrete, applying waterproof plaster of about 25 mm thick for the floor area of the depression and about 18 mm on the side walls of the depression and continue the vertical treatment if necessary on the walls above proposed floor finish. |
| 170 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) Please Enable Macros to View BoQ information |
| 171 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.With material conforming to Grade-II (size range 53 mm to 0.075 mm ) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 23, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 06, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysNov 06, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender