Tender For Special Repairs To Barrack In Bldg No P-24 Of Hq 51 Sub Area Under Ge Narangi
Tender Value
33.97 Lakhs
Estimated cost
Bid Submission
11 Nov 2026
15 days left
EMD
67958
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup Metro → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repairs To Barrack In Bldg No P-24 Of Hq 51 Sub Area Under Ge Narangi
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete and paving not exc 15 cm thick (below or above ground level) complete all as specified and as directed. |
| 2 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed. |
| 3 | Demolition of brick work /stone masonry masonry built in cement mortar of any description all as specified and directed. |
| 4 | Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each etc complete all as specified and as directed. |
| 5 | Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4.0 Sqm each etc complete all as specified and as directed. |
| 6 | Taking down cement plaster of any description hacking for key or raking out joint on old brick work/ stone /concrete surface etc complete all as specified and as directed. |
| 7 | Demoition of Stone slabs and tiles of any description or thickness in floors, aprons , laid bedded and pointed in any mortar etc complete all as specified and as directed. |
| 8 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise etc complete all as specified and as directed. |
| 9 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and as directed. |
| 10 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed. |
| 11 | Demolition of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet) etc complete all as specified and as directed. |
| 12 | Dismantling boarding, any description, fixed in any position with scew as in framed work etc complete all as specified and as directed. |
| 13 | M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe 410 -W (Gde- E- 250) quality-A etc complete all as specified and as directed. |
| 14 | M&L Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 etc complete all as specified and as directed. |
| 15 | S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/ cladding to wall, fixed with self tapping screws etc complete all as specified and as directed. |
| 16 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPA as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed. |
| 17 | S&F in repairs 7 to 8 mm hollow profile thickness thick PVC Coloured Sheet (any Shape, coloured, pattern as approved ) suitably placed in false ceiling incl making sunken side corner, design as directed. etc incl grid work made of G.I./M.S. as per Mfd Instruction etc complete all as specified and as directed. |
| 18 | M&L for 75 mm thick cement concrete type D- 2, (1:4:8) (40mm graded aggregate) as in sub base of flooing etc complete all as specified and as directed. |
| 19 | M&L for cement concrete type B-0 (1:2:4) (12.5 mm graded stone aggregates) 25 mm thick as in sub base of flooring etc complete all as specified and as directed. |
| 20 | M&L for 75 mm thick PCC (1:3:6), type C-1, using 20 mm graded aggregates as in plinth protection etc, finished even and smooth without using extra cement complete all as specified including joints filling with sealing compound Grade \\"A\\" complete all as specified and directed. |
| 21 | M&L for Screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes etc complete all as specified and as directed. |
| 22 | M&L for Rendering 10 mm thick in CM (1:3) for backing coat of tiles / dado etc complete all as specified and as directed. |
| 23 | M & L for joint Free Non - skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) Size of tiles 600mmX1200mm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed. |
| 24 | All as per item No. 23 above but as in vertical surface etc complete all as specified and as directed. |
| 25 | M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and Mirror polishing incl cutting edges etc complete all as specified and as directed. |
| 26 | All as per item No. 25 above but as in skirting /dado / Vertical Surface etc complete all as specified and as directed. |
| 27 | M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work on old surface where ever required to give high gloss finish complete etc complete all as specified and as directed. |
| 28 | M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite complete all as specified and as directed. |
| 29 | M&L for Sand filling under floors or in foundations including watering and consolidation all as specified and directed. |
| 30 | M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment etc complete all as specified and as directed. |
| 31 | M & L for heavy duty parking tiles coloured tiles 8 to 9 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement etc complete all as specified and as directed. |
| 32 | M&L Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) etc complete all as specified and as directed. |
| 33 | M&L Brickwork (Old size Brick) with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:4) etc complete all as specified and as directed. |
| 34 | M&L Brickwork (Old size Brick)with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4) etc complete all as specified and as directed. |
| 35 | M&L for plain cement concrete Type D-2 (1:4:8) (with using 40 mm graded stone aggregates) as in foundations and mass concrete etc complete all as specified and as directed. |
| 36 | M&L for providing plain cement concrete (1:2:4) type B-0 with using 12.50 mm graded stone aggregate as in surface channels and drains complete all as specified and directed. |
| 37 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. |
| 38 | M&L providing cement concrete type B0 (1:2:4) (12.50mm graded stone aggregate) in copings, parapets and railing upto 60cm height, leveling concrete for Roof slab, kerbs, water troughs/Chajjas and the like including weathering, slightly rounded or chamfered angles and throating as directed. |
| 39 | M&L for Pre cast cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM (1:6) etc complete all as specified and directed. |
| 40 | M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished surfaces of concrete complete all as specified and directed. |
| 41 | M&L RCC (Nominal mix) type A-1, (1:1.5:3) (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed. |
| 42 | M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed. |
| 43 | All as per item No 43 above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed. |
| 44 | M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed. |
| 45 | M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed. |
| 46 | M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed. Notes : WPC shall be measured and paid seperately |
| 47 | Supply only water proofing compound (Liquid) complete all as specified and as directed. |
| 48 | S&F Factory made 1.25 mm thick pressed steel frame of size 125 X 60 mm for door with one ore more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed. |
| 49 | S&F 35mm thick flush shutter solid core construction with decorative choice lamination both sides of shutter, kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 50 | M&L for cement concrete (1:3:6) type C-1 (using 20mm graded aggregate) as in hold fast and filling of pressed steel chowkat etc complete all as specified and as directed. |
| 51 | S&F Providing and fixing factory made power coated uPVC colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories incl door sapng, lever handle, standard cylinder, centre stirker, 3 D hinges, striker, drainag, galzing bridge, silicon sealant etc . (Note: The unit rate quoted by contractor excludes cost of glass, wire cloth and includes all other connected accessories) |
| 52 | S&F Powder Coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows ventilators/Partition etc with one or more rebates including joining cleat for fixing etc. complete shall as specified and as directed. |
| 53 | S&F Aluminium Powder Coating (minimum thickness of powder coating 50 micron frame in aluminium partions having horizontal & vertical distance between two frames not exc 1.00 m & section of size 50 mm x 44.5mm of 2 mm thickness of such type arrangement for fixing glass/pre-laminated board on both/one side complete with fixed in brick masonary/conc work by necessary drilling & rawl plug arrangement in (floor/glass/etc.) Note - Glass / particle board shall be measured and paid separately under respective items. |
| 54 | S&F in repairs door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg with alumnium die cost body etc complete all as specified and as directed. |
| 55 | S&F 8mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required incl fixing arrangements, etc complete all as specified and as directed. |
| 56 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed. |
| 57 | S&F 5.5mm thick tinted sheet glass and glazing with oil putty in squares exc 0.5 sq. m in each pane etc complete all as specified and as directed. |
| 58 | S&F 9mm thick Prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminations & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed. |
| 59 | S&F Fancy type Brass barrel tower bolts bolt 200mm long of extruded section etc complete all as specified and as directed. |
| 60 | S&F Fancy type Brass handles 150mm long, cast type, anodised etc complete all as specified and as directed. |
| 61 | S&F Fancy type Brass, sliding door bolt 300mm long with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed etc complete all as specified and as directed. |
| 62 | S&F Fancy type Brass Door stopper Overall length of cover plate 150 mm long Ditto, but of brass body and tongue with hard drawn steel spring etc complete all as specified and as directed. |
| 63 | S&F 110 mm PVC, SWR pipes, single socketed in any length with rubber ring joint fixed to walls etc etc complete all as specified and directed. |
| 64 | S&F 110 mm PVC, SWR pipes, single socketed in any length with rubber ring joint fixed to walls etc etc complete all as specified and directed. |
| 65 | M&L for 1mm thick wall care putty on wall including preparation of surface with sand paper etc to obtain smooth surface etc complete all as specified and as directed. |
| 66 | M&L for Preparing new plastered suface of walls and applying two coats distemper oil emulsion, white or tinted over a coat of primer etc complete all as specified and as directed. |
| 67 | M&L for Preparing old plastered suface of walls and applying two coats distemper oil emulsion, white or tinted over a coat of primer etc complete all as specified and as directed. |
| 68 | M&L for preparation old plastered surface of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance (Apex Ultima), dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces etc complete all as specified and as directed. |
| 69 | All as per item no 69 above but new plastered surface of wall complete all as specified and directed. |
| 70 | M&L for Preparing new plastered suface of walls and applying two coats cement base paint etc complete all as specified and as directed. |
| 71 | S&F in repairs stainless steel decorative curtain rod of 25 mm bore incl fancy finale caps cap (02 nos in each curtain rod) etc complete all as specified and as directed. |
| 72 | S&F in repair Brass Chromium Plated designer Bracket for curtain rod of dia 25 mm dia made out of SS Flat not less than 20 mm wide 1.50 mm thick and overall length not less than 160 mm fixed with screws min 2 Nos with Rawl Plug of size not less than 50 mm long etc complete all as specified and as directed. |
| 73 | M&L for Preparation of new or previously un-treated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed. |
| 74 | Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge. |
| 75 | Taking down ceiling/exhaust/wall fan including connection wires carefully and deposit to MES store in safe custody all as directed by Engineer-in-Charge. |
| 76 | M&L Point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in and including PVC Conceled Conduit with all accessories including fabricated MS/PVC terminal boxes fixed flush box and cover plate ( for modular Switch socket ) with wall surface for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as directed. |
| 77 | All as per item serial No. 76 here-in-before but One 3 pin socket outlet 6 amps on the same board with other switches complete all as specified and directed. |
| 78 | All as per item serial No. 76 here-in-before but One socket outlet 3 pin 6 Amp on independent board complete all as specified and directed. |
| 79 | All as per item serial No. 76 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable complete all as specified and directed. |
| 80 | S&F switch modular type 6 Amp 240 Volts single one way (ISI marked) complete all as specified and directed. |
| 81 | S&F modular socket, 6 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 82 | S&F modular switch 1 way 16 amp, 1 module complete all as specified and as directed. |
| 83 | S&F modular socket, 16 Amp 2/3 pin combined, 2 module complete all as specified and as directed. |
| 84 | S&F stepped type modular electronic fan regulator, two module size, flush type complete all as directed. |
| 85 | S&F ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as directed. |
| 86 | S& F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp 240 V complete all as directed. |
| 87 | Supply and fixing in repair LED lights fitting 1x 20W, 220V, AC decorative batten type connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 88 | Supply and fixing in repairs round shape 15 watt 220 volts AC surface/ recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 89 | Supply and fixing in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 90 | Supply & fix in repair MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate complete all as specified and directed. |
| 91 | Supply & fix in repair MCB DB of sheet metal enclosure double door SPN 8 way with 200 A rated bus bar and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate all as directed. |
| 92 | S&F in repair/replacement MCCB four pole 100 A, Icu 16KA, thermal magnetic, 415v AC complete all as specified and as directed. Make:- Legrand Cat No 4200 15 or equivalent model of make Hager/Siemens /ABB/Schneider /GE/C&S Electricals |
| 93 | S&F in repair/replacement MCBs, SP 6 to 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and directed. |
| 94 | S&F in repair/replacement MCBs, SPN 32 Amps In accordance with IS/IEC 60898-1, 240 V, 50 Hz, 10 kA ,C-series marked fixing in DBs (DBs catered separately in this Schedule) complete all as specified and directed. |
| 95 | Supply and fixing ceiling fans complete with blades, down rods, and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 96 | Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including excavation and earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009. |
| 97 | S&F in repair/replacement LED 60 W building secruity light made up of pressure die cast housing with high efficient LED as lighting source and PC cover having TOP Opening separate driver compartment with IP66 protection and impact resistance of IK07 and suitable for dia upto 43 mm complete all as specified and directed. |
| 98 | M&L for building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed. |
| 99 | M&L for wiring with 2 runs of 6 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith single run of 6 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old wiring and type of conduit complete all as specified and directed. Note: 2 run of 6 Sqmm cable and 1 run of 6 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 100 | M&L for wiring with 2 runs of 4 sqmm, single core,FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith single run of 4 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old wiring and type of conduit complete all as specified and directed. Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit altogether shall be measured as one unit. |
| 101 | Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 4 core complete all as specified and directed. |
| 102 | Excavation in trenches n.exc 1.5mtr wide and n.exc. 1.5m in depth for foundation and getting out in soft/loose soil complete all as specified and directed. |
| 103 | Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed. |
| 104 | M&L for bricks sub class ‘B’ brick old size for cable protection laid in flat in trenches over the cable perpendicular to the direction of cable complete all as specified. |
| 105 | M&L Returning filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm complete all as specified and directed. |
| 106 | Removing of excavated soil not exc 50cm & depositing where as directed at a level n.exc 1.5m above starting point complete all as specified and directed. Please Enable Macros to View BoQ information |
| 107 | Removing of excavated soil not exc 50cm & depositing where as directed at a level n.exc 1.5m above starting point complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 22, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender